Imixholo fihla
1 I-EPH ULAWULO R37-RF 3 Zone RF Wireless Programmer
2 Izicwangciso zenkqubo yefektri
3 Ukumisela umhla kunye nexesha
4 Ukulungelelanisa izicwangciso zenkqubo
5 ReviewUkufaka useto lwenkqubo
6 Ukunyusa umsebenzi
7 Umsebenzi wangaphambili
8 Qhagamshela i-thermostat yeRF kunye nomdwelisi wenkqubo
9 Khuphela umsebenzi
10 Ukusetha kwakhona okuyintloko
11 Amaxwebhu / Izibonelelo
11.1 Iimbekiselo
12 Izithuba eziyeleleneyo

EPH ULAWULO uphawu

I-EPH ULAWULO R37-RF 3 Zone RF Wireless Programmer

I-EPH ULAWULO R37-RF 3 Zone RF Wireless Programmer

Iisetingi zefektri

Inkqubo: 5/2D
Isibane ngasemva: Vula
Iphedi yezitshixo: ayitshixekanga
Ukukhuselwa kwiNqabaka: KUVALIWE

Izicwangciso zenkqubo yefektri

5/2D
P1 IYAQHUBEKA P1 OFF P2 IYAQHUBEKA P2 OFF P3 IYAQHUBEKA P3 OFF
Mvulo-Lwesihlanu 6:30 8:30 12:00 12:00 16:30 22:30
NgoMgqibelo-Ngelanga 7:30 10:00 12:00 12:00 17:00 23:00
 

Zonke iintsuku ezisi-7

 7D
P1 IYAQHUBEKA P1 OFF P2 IYAQHUBEKA P2 OFF P3 IYAQHUBEKA P3 OFF
6:30 8:30 12:00 12:00 16:30 22:30
 

Yonke imihla

 24H
P1 IYAQHUBEKA P1 OFF P2 IYAQHUBEKA P2 OFF P3 IYAQHUBEKA P3 OFF
6:30 8:30 12:00 12:00 16:30 22:30

Ukuseta ngokutsha umdwelisi wenkqubo
Kuyimfuneko ukucofa iqhosha le-RESET phambi kocwangciso lokuqala.
Eli qhosha libekwe emva kwesigqubuthelo kumphambili weyunithi.

ULAWULO lwe-EPH R37-RF 3 Zone RF Wireless Programmer 1

Ukumisela umhla kunye nexesha

Yehlisa isigqubuthelo esingaphambili kwiyunithi. Cofa u-Kulungile
Hambisa isikhethi sokutshintshela kwi-CLOCK SET indawo. Cofa u-Kulungile

  • Cinezela u-+ okanye-- amaqhosha ukukhetha usuku. Cofa u-Kulungile
  • Cofa u-+ okanye-- amaqhosha ukukhetha inyanga. Cofa u-Kulungile
  • Cinezela u-+ okanye-- amaqhosha ukukhetha unyaka. Cofa u-Kulungile
  • Cofa i + okanye – amaqhosha ukukhetha iyure. Cofa u-Kulungile
  • Cofa i + okanye – amaqhosha ukukhetha umzuzu. Cofa u-Kulungile
  • Cofa i + okanye – amaqhosha ukukhetha 5/2D, ​​7D okanye 24H Cofa Lungile

Umhla, ixesha kunye nomsebenzi zibekiwe ngoku. Hambisa umkhethi wokutshintsha kwindawo ethi RUN ukuze uqhube inkqubo, okanye kwiPROG SET indawo yokutshintsha isicwangciso senkqubo.

ON/OFF ukhetho lwexesha
Kukho iindlela ezi-4 ezikhoyo kulo mdwelisi wenkqubo ukuze abasebenzisi bakhethe kwisicelo sabo somntu ngamnye.

  • NGOKUZENZAKALELAYO Umdwebi wenkqubo usebenza 3 'ON/OFF' amaxesha ngosuku.
  • YONKE IMINI Umdwebi wenkqubo usebenza 1'ON/OFF' ngosuku.
    Oku kusebenza ukusuka kwixesha lokuqala ON ukuya kwixesha lesithathu OFF.
  • ON Umdwelisi wenkqubo uvuliwe ngokusisigxina. **KUVULA**
  • CIMA Umdwelisi wenkqubo ucinywe ngokusisigxina. **VUMA**

Yehlisa isigqubuthelo esingaphambili kwiyunithi. Ngokucofa iqhosha, unokutshintsha phakathi kwe-AUTO / LONKE USUKU / ON / OFF kuMmandla woku-1.
Phinda le nkqubo yeZone 2 ngokucofa iqhosha kunye neZone 3 ngokucofa iqhosha.

Ukulungelelanisa izicwangciso zenkqubo

Yehlisa isigqubuthelo esingaphambili kwiyunithi. Hambisa iswitsha yomkhethi kwindawo yePROG SET. Ngoku ungayenza indawo yenkqubo 1.

ULAWULO lwe-EPH R37-RF 3 Zone RF Wireless Programmer 2

Cinezela i-+ okanye-- amaqhosha ukulungisa i-P1 NGEXESHA. Cofa u-Kulungile
Cinezela i-+ okanye-- amaqhosha ukulungisa ixesha le-P1 OFF. Cofa u-Kulungile

Phinda le nkqubo ukunyenyisa ON & OFF amaxesha kwi P2 & P3.

Cofa indawo yesi-2 ukhethe kwaye uphinda inkqubo engentla ukulungelelanisa iZone2.
Cofa indawo yesi-3 ukhethe kwaye uphinda inkqubo engentla ukulungelelanisa iZone3.
Xa kugqityiwe, susa umkhethi kwindawo ethi RUN.

ReviewUkufaka useto lwenkqubo

Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa iswitsha yomkhethi kwindawo yePROG SET.
Ngokucofa u-OK oku kuya kuphindaview Ngalinye kumaxesha o-ON/OFF kwi-P1 ukuya kwi-P3 kuMmandla woku-1.

ULAWULO lwe-EPH R37-RF 3 Zone RF Wireless Programmer 3

Cofa indawo yesi-2 ukhethe kwaye uphinda inkqubo engentla ukulungelelanisa uMmandla wesi-2.
Cofa indawo yesi-3 ukhethe kwaye uphinda inkqubo engentla ukulungelelanisa uMmandla wesi-3.
Xa kugqityiwe, susa umkhethi kwindawo ethi RUN.

Ukunyusa umsebenzi

Lo msebenzi uvumela umsebenzisi ukuba andise ixesha le-ON kwi-1, i-2 okanye iiyure ze-3.
Ukuba izowuni onqwenela ukuBoost imiselwe ukuba IVIME, unendawo yokuyivula kangangeeyure ezi-1, ezi-2 okanye ezi-3.

Cinezela iqhosha elifunekayo, kwi-Zone 1, ye-Zone 2 kunye ne-Zone 3. - kanye, kabini okanye kathathu ngokulandelanayo.
Ukurhoxisa umsebenzi we-boost, cinezela ngokulula iqhosha elifanelekileyo kwakhona.

Umsebenzi wangaphambili

Lo msebenzi uvumela umsebenzisi ukuba azise phambili ixesha elilandelayo lokutshintsha.
Ukuba indawo ngoku ibekwe ixesha lokuba OFF kwaye i-ADV icinezelwe, indawo iya kuvulwa kude kube sekupheleni kwexesha elilandelayo lokutshintsha.
Ukuba indawo ngoku ibekwe ixesha lokuba i-ON kwaye i-ADV icinezelwe, indawo iya kucinywa kude kube sekupheleni kwexesha elilandelayo lokutshintsha.

Cinezela uMmandla woku-1, kwindawo yesi-2 okanye kwindawo yesi-3.
Ukurhoxisa umsebenzi weADVANCE, cinezela ngokulula iqhosha leADV elahlukileyo kwakhona.

Imo yeholide

Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa isikhethi sokutshintshela kwindawo ethi RUN.
Cinezela iqhosha leholide.

Umhla kunye nexesha langoku liya kudanyaza kwiscreen. Ngoku uyakwazi ukufaka umhla kunye nexesha oceba ukubuya ngalo.

Cinezela u-+ okanye-- amaqhosha ukukhetha usuku. Cinezela iHolide
Cofa u-+ okanye-- amaqhosha ukukhetha inyanga. Cinezela iHolide
Cinezela u-+ okanye-- amaqhosha ukukhetha unyaka. Cinezela iHolide
Cofa i + okanye – amaqhosha ukukhetha iyure. Cinezela iHolide

Ukuvula imo yeHolide cofa iqhosha.
Ukurhoxisa imo yeHolide cofa iqhosha kwakhona.

Kungenjalo Imo yeHolide iya kuthi ingasebenzi ngexesha kunye nomhla ongenisiweyo.

Qhagamshela i-thermostat yeRF kunye nomdwelisi wenkqubo

Kwiprogramu
Nciphisa isiciko sangaphambili kwaye ushukumise umkhethi wokutshintshela kwindawo ethi RUN. Cinezela i-iqhosha - imizuzwana emi-5.
I-Wireless Connect iya kuvela kwisikrini.

ULAWULO lwe-EPH R37-RF 3 Zone RF Wireless Programmer 4

Kwi-thermostat yegumbi le-RFR elingenazingcingo okanye i-RFC engenazingcingo yesilinda thermostat
Cofa iKhowudi iqhosha. Oku kungaphakathi kwizindlu kwi-PCB.

Kwiprogramu
Indawo yoku-1 iya kuqalisa ukudanyaza. Cinezela i-, okanye iqhosha lezowuni onqwenela ukuqhagamshela i-thermostat kuyo.

I-thermostat iya kubala ukuya phezulu ukuya kwinani lezowuni edityaniswe nayo. Xa ifikelela kwinani lezowuni edityaniswe nayo ngokucinezela i-handwheel kwi-thermostat.
Umdwelisi wenkqubo ngoku usebenza kwimowudi engenazingcingo. Ubushushu be-thermostat engenazingcingo buboniswa ngoku kwiprogramu.
Phinda le nkqubo kwindawo yesibini neyesithathu ukuba iyafuneka.

Susa uqhagamshelwano lwe-thermostat yeRF kumdwelisi wenkqubo

Kwiprogramu

Nciphisa isiciko sangaphambili kwaye ushukumise isikhethi sitshintshe kwi-RUN indawo.
Cinezela i-iqhosha - imizuzwana emi-5.
I-Wireless Connect iya kuvela kwisikrini.

ULAWULO lwe-EPH R37-RF 3 Zone RF Wireless Programmer 5

Cinezela i-iqhosha - imizuzwana emi-3. Oku kuya kucoca lonke uqhagamshelo lwe-RF ngokwenza oko kuqhawulwa zonke iithermostats kwi-timewitch.
Cofa iqhosha elithi Kulungile.

Ukukhetha imo yokukhanya ngasemva

Kukho iisetingi ezimbini zokukhetha. Useto oluhlala luhleli lwasefektri LUVULIWE.

ON Isibane sangasemva sivuliwe ngokusisigxina.
NGOKUZENZAKALELAYO Xa ucofa naliphi na iqhosha i-backlight ihlala ivuliwe imizuzwana eyi-10.

Ukunyenyisa useto lwesibane
Yehlisa isigqubuthelo esingaphambili kwiyunithi.
Hambisa isikhethi sokutshintshela kwindawo ethi RUN.

Cinezela iqhosha elithi Kulungile imizuzwana emi-5.
Cinezela nokuba + okanye – amaqhosha ukukhetha ON okanye imo ye-AUTO.
Cofa iqhosha elithi Kulungile.

Khuphela umsebenzi

Kopisha umsebenzi ungasetyenziswa kuphela ukuba umdwelisi ukwimo ye-7d.
Yehlisa isigqubuthelo kumphambili womdwelisi wenkqubo.
Hambisa iswitsha yomkhethi kwindawo yePROG SET.

ULAWULO lwe-EPH R37-RF 3 Zone RF Wireless Programmer 6

Okokuqala, inkqubo enye yeentsuku zeveki kunye neshedyuli onqwenela ukuyikhuphela kwezinye iintsuku.

  • Ngelixa usekho ngaloo mini cofa kwaye ubambe iqhosha imizuzwana emi-3.
  • Oku kuyakusa kwi Khuphela isikrini.
  • Usuku lweveki ekufuneka lukhutshelwe ngalo luyaboniswa kwaye nosuku emayikhutshelwe kulo luyadanyaza.
  • Cofa iqhosha + ukukopa ishedyuli ukuza kuthi ga kulo mhla.
  • Cofa iqhosha-ukutsiba olu suku
  • Qhubeka ngale ndlela ngokucinezela iqhosha ukukopa ishedyuli kusuku oludanyazayo kwaye ngokucofa iqhosha ukutsiba loo mini.
  • Xa ugqibile cofa iqhosha elithi Kulungile
  • Hambisa isikhethi sokutshintshela kwindawo ethi RUN.

Ukusetha kwakhona okuyintloko

Yehlisa isigqubuthelo kumphambili womdwelisi wenkqubo. Kukho iihenjisi ezine ezibambe isigqubuthelo endaweni. Phakathi kweehinge ze-3 kunye ne-4 kukho umngxuma ojikelezayo. Faka ipeni yebhola okanye into efanayo ukuseta ngokutsha umdwelisi wenkqubo.
Emva kokucofa iqhosha lokuseta ngokutsha, umhla kunye nexesha ngoku kuya kufuneka zicwangciswe ngokutsha.

Amaxwebhu / Izibonelelo

I-EPH ULAWULO R37-RF 3 Zone RF Wireless Programmer [pdf] Incwadi Yomyalelo
R37-RF, R37-RF 3 Zone RF Wireless Programmer, 3 Zone RF Wireless Programmer, RF Wireless Programmer, Wireless Programmer

Iimbekiselo

Izithuba eziyeleleneyo

Shiya uluvo

Idilesi yakho ye-imeyile ayizupapashwa. Iindawo ezifunekayo ziphawulwe *