Danfoss VLT Soft Starter MCD600 Modbus RTU Card
Ukhuseleko
Ukuzihlangula
Exampiiles kunye nemizobo kule ncwadana zibandakanyiwe kuphela ngeenjongo zokubonisa. Ulwazi oluqulethwe kule ncwadana lunokutshintshwa nangaliphi na ixesha kwaye ngaphandle kokwazisa kwangaphambili. Uxanduva okanye uxanduva aluzange lwamkelwe kumonakalo othe ngqo, ongathanga ngqo, okanye obangelwa kukusetyenziswa okanye ukusetyenziswa kwesi sixhobo.
Izilumkiso INGOZI YOKOTSHA
Ukuqhoboshela okanye ukususa izincedisi ngelixa isiqalisi esithambileyo siqhagamshelwe kwi-mains voltaginokubangela ukwenzakala.
Phambi kokuncamathisela okanye ukususa izincedisi, khetha isiqalisi esithambileyo kwi-mains voltage.
ISILUMKISO UMNGCIPHEKO WOKWENZAKALA KOMNTU KUNYE NOKONAKALA KWEZIXHOBO
Ukufaka izinto zangaphandle okanye ukubamba ngaphakathi kwisiqalisi esithambileyo ngelixa isivalo sokwandisa sivulekile kunokubeka abasebenzi emngciphekweni kwaye kunokonakalisa isiqalisi esithambileyo.
Musa ukufaka izinto zangaphandle kwisiqalisi esithambileyo nesivula isivalo sezibuko.
Sukuchukumisa ngaphakathi kwisiqalisi esithambileyo nesivula isiciko sezibuko.
Ulwazi olubalulekileyo lomsebenzisi
Qwalasela onke amanyathelo okhuseleko ayimfuneko xa ulawula isiqalisi esithambileyo ukude. Yazisa abasebenzi ukuba oomatshini banokuqalisa ngaphandle kwesilumkiso.
Umfakeli unoxanduva lokulandela yonke imiyalelo ekule ncwadana kunye nokulandela usetyenziso oluchanekileyo lombane.
Sebenzisa zonke iindlela eziqhelekileyo ezivunyiweyo zehlabathi zonxibelelwano lweRS485 xa ufaka kwaye usebenzisa esi sixhobo.
Intshayelelo
Ukuhambelana
Eli khadi lokwandisa unxibelelwano lifanelekile ukusetyenziswa neVLT® Soft Starter MCD 600. Ikhadi lifumaneka kwiinguqulelo ezi-2:
175G0127: VLT® Soft Starter MCD 600 Modbus RTU Card
I-175G0027: I-VLT® Soft Starter MCD 600 Modbus RTU Card kunye noKhuseleko lweFault Fault.
Le ncwadana ilungele ukusetyenziswa nazo zombini iinguqulelo.
Esi Sikhokelo soFakelo senzelwe ukusetyenziswa noguqulelo 2.x lwekhadi leVLT® Soft Starter MCD 600 Modbus RTU. Inguqulo ye-1.x yeKhadi le-Modbus RTU ayixhasi abasebenzisi besiko, uqhagamshelo lwe-TCP, okanye ukusebenza kwe-IoT.
Ukuhlohla
Ukufakela iKhadi Lokwandiswa Inkqubo
Tyhiliza isikrudrayiva esisicaba esincinci kwisithuba esisembindini wesigqubuthelo sokwandiswa kwezibuko kwaye wenze lula isigqubuthelo kude kwisiqalisi esithambileyo.
- Umgca wekhadi kunye ne-port yokwandisa.
- Lityhale ngobunono ikhadi ecaleni kweentsimbi zesikhokelo de licofe kwisiqalisi esithambileyo.
Example
Ukuqhagamshela kwiNethiwekhi
Ikhadi lokwandisa kufuneka lifakwe kwisiqalisi esithambileyo.
Inkqubo
- Buyisela amandla olawulo.
- Qhagamshela iingcingo zentsimi ngeplagi yokudibanisa indlela ezi-5.
Example
| Iphini | Umsebenzi |
| 1, 2 | Idatha A |
| 3 | Eqhelekileyo |
| 4, 5 | Idatha B |
Ukusebenza
Izinto ezifunekayo kuqala
IKhadi le-Modbus RTU kufuneka lilawulwe ngumthengi we-Modbus (ofana ne-PLC) ehambelana neNgcaciso yeProtocol ye-Modbus.
Ukusebenza ngempumelelo, umxhasi kufuneka axhase yonke imisebenzi kunye nojongano oluchazwe kule ncwadana.
Uqwalaselo loMxumi
Kwimodbus esemgangathweni ye-11-bit yothumelo, misela umxhasi we-2 yokumisa amasuntswana angenawo ukulingana kunye ne-1 yokuyeka i-odd okanye i-parity.
Nge-10-bit yogqithiso, misela umxhasi kwi-1 stop bit.
Kuzo zonke iimeko, izinga le-baud yomxhasi kunye nedilesi yomncedisi kufuneka ihambelane nezo zibekwe kwiiparamitha 12-1 ukuya kwi-12-4.
Ithuba lokuvota kwedatha kufuneka libe lide ngokwaneleyo ukuze imodyuli iphendule. Amathuba amafutshane okuvota anokubangela ukungangqinelani okanye ukuziphatha okungalunganga, ngakumbi xa kufundwa iirejista ezininzi. Elona xesha lincinci licetyiswayo lokuvota lingama-300 ms.
Uqwalaselo
Izicwangciso zeModbus Network
Seta iiparamitha zonxibelelwano lwenethiwekhi yekhadi usebenzisa isiqalisi esithambileyo. Ukufumana iinkcukacha malunga nendlela yokumisela isiqalisi esithambileyo, jonga i-VLT® Soft Starter MCD 600 IsiKhokelo sokuSebenza.
Itheyibhile 1: Izicwangciso zeParameter
| Ipharamitha | Igama lepharamitha | Inkcazo |
| 12-1 | Modbus Idilesi | Icwangcisa idilesi yenethiwekhi yeModbus RTU kumqalisi othambileyo. |
| 12-2 | Modbus Baud Ixabiso | Ikhetha izinga le-baud kunxibelelwano lwe-Modbus RTU. |
| 12-3 | Modbus Ukulingana | Ikhetha ukulingana kunxibelelwano lwe-Modbus RTU. |
| 12-4 | Modbus Kuphele ixesha | Ikhetha ixesha lokuvala unxibelelwano lwe-Modbus RTU. |
Ukuvumela Ulawulo Lwenethiwekhi
Isiqalisi esithambileyo samkela kuphela imiyalelo esuka kwikhadi lokwandisa ukuba iparamitha 1-1 Umthombo womyalelo usetelwe kuThungelwano.
ISAZISO Ukuba igalelo lokusetha ngokutsha liyasebenza, isiqalisi esithambileyo asisebenzi. Ukuba ukuseta ngokutsha akufuneki, faka ikhonkco kwi-terminals SETHA kwakhona, COM+ kwisiqalisi esithambileyo.
Ii-LED zeengxelo
| Ubume be-LED | Inkcazo |
| Cimile | Isiqalisi esithambileyo asixhaswanga. |
| On | Unxibelelwano luyasebenza. |
| Ukudanyaza | Unxibelelwano alusebenzi. |
ISAZISO Ukuba unxibelelwano alusebenzi, umqalisi othambileyo unokukhubeka kuNxibelelwano lweNethiwekhi. Ukuba iparameter 6-13 UThungelwano loNxibelelwano lusetelwe kuhambo oluthambileyo kunye neLog okanye i-Trip Starter, isiqalisi esithambileyo sifuna ukusetwa kwakhona.
IiRejista zeModbus
Uqwalaselo lwePLC
Sebenzisa iitheyibhile eziku-5.5 Imo yoMgangatho ukwenza imaphu yeerejista ngaphakathi kwesixhobo kwiidilesi ezingaphakathi kwePLC.
ISAZISO Zonke iirejista ezibhekiselele kwiirejista zithetha iirejista ezingaphakathi kwisixhobo ngaphandle kokuba kuchazwe ngenye indlela.
Ukuhambelana
Ikhadi leModbus RTU lixhasa iindlela ezi-2 zokusebenza:
KwiMode yoMgangatho, isixhobo sisebenzisa iirejista ezichazwe kwiNkcazo yeProtocol yeModbus.
KwiModyuli yeLifa, isixhobo sisebenzisa iirejista ezifanayo njengekliphu-kwiModyuli yeModbus enikezelwe nguDanfoss ukuze isetyenziswe neziqalisi ezithambileyo ezindala. Ezinye iirejista zahlukile kwezo zichazwe kwiNkcazo yeProtocol ye-Modbus.
Ukuqinisekisa uLawulo oluKhuselekileyo noluyimpumelelo
Idatha ebhaliweyo kwisixhobo ihlala kwiirejista zayo de idatha ibhalwe ngaphezulu okanye isixhobo siqaliswe kwakhona.
Ukuba i-soft starter kufuneka ilawulwe ngeparameter 7-1 Command Override okanye kufuneka ivaliwe ngokufaka ngokutsha (i-terminal RESET, COM +), imiyalelo ye-fieldbus kufuneka isuswe kwiirejista. Ukuba umyalelo awucinywanga, uphinda uthunyelwe kwisiqalisi esithambileyo
xa ulawulo lwebhasi luqala kwakhona.
Ulawulo lweParameter
Iiparamitha zinokufundwa kwaye zibhalwe kwisiqalo esithambileyo. Ikhadi le-Modbus RTU linokufunda okanye libhale ubuninzi beerejista ze-125 kumsebenzi we-1.
ISAZISO Inani elipheleleyo leeparamitha kwi-soft starter inokwahluka ngokwemodeli kunye noluhlu lweparameter ye-soft starter. Ukuzama ukubhala kwirejista engahambelani neparameter ibuyisela ikhowudi yephutha 02 (idilesi yedatha engekho mthethweni). Funda irejista 30602 ukumisela inani elipheleleyo leeparamitha kwisiqalo esithambileyo.
ISAZISO Musa ukuwatshintsha amaxabiso angagqibekanga e-Iparameters eziPhambili (iqela leparamitha 20-** Iiparamitha ezikwinqanaba eliPhezulu). Ukutshintsha la maxabiso kunokubangela ukuziphatha okungalindelekanga kwisiqalisi esithambileyo.
Imo esemgangathweni
Iirejista zomyalelo kunye noqwalaselo (Funda/Bhala)
Itheyibhile 2: INkcazelo yeeRejista zokuFunda/zoBhala
| Bhalisa | Inkcazo | Amasuntswana | Iinkcukacha |
| 40001 | Umyalelo (bhala omnye) | 0–7 | Ukuthumela umyalelo kumqali, bhala ixabiso elifunekayo: 00000000 = Yeka
00000001 = Qala 00000010 = Lungisa kwakhona 00000100 = Ukumisa ngokukhawuleza (unxweme ukuya kumisa) 00001000 = Uhambo lonxibelelwano olunyanzelweyo 00010000 = Qala ukusebenzisa iParameter Set 1 00100000 = Qala ukusebenzisa iParameter Set 2 01000000 = Reserved |
| Bhalisa | Inkcazo | Amasuntswana | Iinkcukacha |
| 10000000 = Igciniwe | |||
| 8–14 | Igciniwe | ||
| 15 | Kufuneka = 1 | ||
| 40002 | Igciniwe | ||
| 40003 | Igciniwe | ||
| 40004 | Igciniwe | ||
| 40005 | Igciniwe | ||
| 40006 | Igciniwe | ||
| 40007 | Igciniwe | ||
| 40008 | Igciniwe | ||
| 40009–40xxx | Ulawulo lweParameter (ukufunda okukodwa okanye okuninzi / ukubhala) | 0–15 | Lawula umqalisi othambileyo weeparamitha ezicwangcisekileyo. Jonga iVLT® Soft Start-er MCD 600 IsiKhokelo sokuSebenza ukuze ufumane uluhlu olupheleleyo lweparamitha. |
Iirejista zeNgxelo yeSimo (Funda Kuphela)
ISAZISO Kwiimodeli ze-MCD6-0063B kunye ezincinci (i-ID ye-soft starter imodeli 1 ~ 4), i-current kunye ne-frequency echazwe ngeerejista zonxibelelwano ziphindwe ka-10 kunexabiso langempela.
Itheyibhile 3: Inkcazo yeerejista zokuFunda
| Bhalisa | Inkcazo | Amasuntswana | Iinkcukacha |
| 30003 | Igciniwe | ||
| 30004 | Igciniwe | ||
| 30005 | Igciniwe | ||
| 30006 | Igciniwe | ||
| 30007 | Igciniwe | ||
| 30008 | Igciniwe | ||
| 30600 | Inguqulelo | 0–5 | Uguqulelo lweprotocol yokubini |
| 6–8 | Uluhlu lweParameter inguqulelo enkulu | ||
| 9–15 | Ikhowudi yodidi lwemveliso: 15 = MCD 600 | ||
| 30601 | Inombolo yomzekelo | 0–7 | Igciniwe |
| 8–15 | I-ID yemodeli yokuqala ethambileyo | ||
| 30602 | Inombolo yepharamitha etshintshiweyo | 0–7 | 0 = Akukho ziparamitha zitshintshileyo
1–255 = Inombolo yesalathiso separamitha yokugqibela itshintshiwe |
| 8–15 | Lilonke inani leeparamitha ezikhoyo kwisiqalisi esithambileyo |
| Bhalisa | Inkcazo | Amasuntswana | Iinkcukacha |
| 30603 | Ixabiso lepharamitha etshintshiweyo | 0–15 | Ixabiso leparamitha yokugqibela etshintshiweyo, njengoko kubonisiwe kwirejista 30602 |
| 30604 | Imeko yokuqalisa | 0–4 | 0 = Igciniwe
1 = Ulungile 2 = Ukuqala 3 = Ukubaleka 4 = Ukuyeka 5 = Ayilunganga (ukuqala ukulibaziseka kwakhona, qalisa kwakhona ukujonga ubushushu, sebenzisa ukulinganisa, igalelo lokusetha kwakhona livuliwe) 6 = Ukhutshiwe 7 = Imo yokucwangcisa 8 = Qhubela phambili 9 = Jog umva |
| 5 | 1 = Isilumkiso | ||
| 6 | 0 = Ayisetyenziswanga
1 = Yasungulwa |
||
| 7 | Umthombo womyalelo
0 = I-LCP ekude, i-Digital Input, iClock 1 = Inethiwekhi |
||
| 8 | 0 = Iiparamitha zitshintshile ukususela okokugqibela ukufundwa kweparamitha
1 = Akukho ziparamitha zitshintshileyo |
||
| 9 | 0 = Ukulandelelana kwesigaba esibi
I-1 = Ukulandelelana kwesigaba esilungileyo |
||
| 10–15 | Igciniwe | ||
| 30605 | Okwangoku | 0–13 | I-avareji ye-rms yangoku kuzo zonke izigaba ezi-3 |
| 14–15 | Igciniwe | ||
| 30606 | Okwangoku | 0–9 | Okwangoku (% motor FLC) |
| 10–15 | Igciniwe | ||
| 30607 | Ubushushu beMoto | 0–7 | Imodeli yobushushu beMoto (%) |
| 8–15 | Igciniwe | ||
| 30608 | Amandla | 0–11 | Amandla |
| 12–13 | Isikali samandla
0 = Phindaphinda-phinda amandla nge-10 ukufumana iW 1 = Phindaphinda-phinda amandla nge-100 ukufumana iW 2 = Amandla (kW) 3 = Phindaphinda amandla nge-10 ukufumana i-kW |
||
| 14–15 | Igciniwe | ||
| 30609 | % Umba wamandla | 0–7 | 100% = amandla e-1 |
| Bhalisa | Inkcazo | Amasuntswana | Iinkcukacha |
| 8–15 | Igciniwe | ||
| 30610 | Umqulutage | 0–13 | Umndilili rms voltage kuzo zonke izigaba ezi-3 |
| 14–15 | Igciniwe | ||
| 30611 | Okwangoku | 0–13 | Inqanaba loku-1 langoku (rms) |
| 14–15 | Igciniwe | ||
| 30612 | Okwangoku | 0–13 | Inqanaba loku-2 langoku (rms) |
| 14–15 | Igciniwe | ||
| 30613 | Okwangoku | 0–13 | Inqanaba loku-3 langoku (rms) |
| 14–15 | Igciniwe | ||
| 30614 | Umqulutage | 0–13 | Isigaba 1 voltage |
| 14–15 | Igciniwe | ||
| 30615 | Umqulutage | 0–13 | Isigaba 2 voltage |
| 14–15 | Igciniwe | ||
| 30616 | Umqulutage | 0–13 | Isigaba 3 voltage |
| 14–15 | Igciniwe | ||
| 30617 | Inombolo yenguqulelo yoluhlu lweParameter | 0–7 | Uluhlu lweParameter yohlaziyo oluncinci |
| 8–15 | Uluhlu lweParameter inguqulelo enkulu | ||
| 30618 | Imo yengeniso yedijithali | 0–15 | Kuwo onke amagalelo, 0 = vula, 1 = ivaliwe (mfutshane)
0 = Qala/Yeka 1 = Igciniwe 2 = Lungisa kwakhona 3 = Igalelo A 4 = Igalelo B I-5 ukuya kwi-15 = Igciniwe |
| 30619 | Ikhowudi yohambo | 0–15 | 'Yabona 5.7 Iikhowudi zohambo |
| 8–15 | Igciniwe | ||
| 30620 | Igciniwe | ||
| 30621 | Ukuphindaphinda | 0–15 | Ukuphindaphinda (Hz) |
| 30622 | Umhlaba wangoku | 0–15 | Umhlaba wangoku (A) |
| 30623-30631 | Igciniwe |
ISAZISO Irejista yokufunda 30603 (Ixabiso leparameter etshintshileyo) iphinda ibhalise iirejista 30602 (Inombolo yepharamitha etshintshileyo) kunye ne-30604 (IiParameters zitshintshile). Soloko ufunda iirejista 30602 kunye 30604 phambi kokuba ufunde irejista 30603.
ExampLes
Uluhlu 4: Umyalelo: Qala
| Umyalezo | Idilesi ethambileyo yokuqalisa | Ikhowudi yokusebenza | Bhalisa idilesi | Idatha | CRC |
| In | 20 | 06 | 40002 | 1 | CRC1, CRC2 |
| Ngaphandle | 20 | 06 | 40002 | 1 | CRC1, CRC2 |
Itheyibhile 5: Soft Starter State: Ukubaleka
| Umyalezo | Idilesi ethambileyo yokuqalisa | Ikhowudi yokusebenza | Bhalisa idilesi | Idatha | CRC |
| In | 20 | 03 | 40003 | 1 | CRC1, CRC2 |
| Ngaphandle | 20 | 03 | 2 | xxx0011 | CRC1, CRC2 |
Itheyibhile 6: IKhowudi yohambo: Ukugcwala kweMotor
| Umyalezo | Idilesi ethambileyo yokuqalisa | Ikhowudi yokusebenza | Bhalisa idilesi | Idatha | CRC |
| In | 20 | 03 | 40004 | 1 | CRC1, CRC2 |
| Ngaphandle | 20 | 03 | 2 | 00000010 | CRC1, CRC2 |
Itheyibhile 7: Khuphela iParameter kwi-Soft Starter - Funda iParameter 5 (I-Parameter 1-5 i-Rotor evaliweyo yangoku), i-600%
| Umyalezo | Idilesi ethambileyo yokuqalisa | Ikhowudi yokusebenza | Bhalisa | Idatha | CRC |
| In | 20 | 03 | 40013 | 1 | CRC1, CRC2 |
| Ngaphandle | 20 | 03 | 2 (bytes) | 600 | CRC1, CRC2 |
Itheyibhile 8: Layisha iParameter enye kwi-Soft Starter - Bhala iParameter 61 (I-Parameter 2-9 ye-Stop Mode), isethi = 1
| Umyalezo | Idilesi ethambileyo yokuqalisa | Ikhowudi yokusebenza | Bhalisa | Idatha | CRC |
| In | 20 | 06 | 40024 | 1 | CRC1, CRC2 |
| Ngaphandle | 20 | 06 | 40024 | 1 | CRC1, CRC2 |
Itheyibhile 9: Layisha iiParameters ezininzi kwi-Soft Starter - Bhala iiParameters 9, 10, 11 (IiParameters 2-2 ukuya kwi-2-4) Beka kwiiNqobo ze-15 s, 300%, kunye ne-350%, ngokulandelanayo.
| Umyalezo | Idilesi ethambileyo yokuqalisa | Ikhowudi yokusebenza | Bhalisa | Idatha | CRC |
| In | 20 | 16 | 40017, 3 | 15, 300, 350 | CRC1, CRC2 |
| Ngaphandle | 20 | 16 | 40017, 3 | 15, 300, 350 | CRC1, CRC2 |
Iikhowudi zohambo
| Ikhowudi | Inkcazo |
| 0 | Akukho luhambo |
| 1 | Ixesha lokuqala eligqithisiweyo |
| Ikhowudi | Inkcazo |
| 2 | Ukugcwala kweMotor |
| 3 | I-motor thermistor |
| 4 | Ukungalingani kwangoku |
| 5 | Ukuphindaphinda |
| 6 | Ukulandelelana kwesigaba |
| 7 | Ugqithiso lwangoko nangoko |
| 8 | Ukulahlekelwa kwamandla |
| 9 | Umsinga ongaphantsi |
| 10 | Ubushushu obugqithisileyo beHeatsink |
| 11 | Uqhagamshelo lweMoto |
| 12 | Igalelo A uhambo |
| 13 | I-FLC iphezulu kakhulu |
| 14 | Ukhetho olungaxhaswanga (umsebenzi awufumaneki ngaphakathi kwedelta) |
| 15 | Impazamo yekhadi lonxibelelwano |
| 16 | Uhambo lwenethiwekhi olunyanzelweyo |
| 17 | Impazamo yangaphakathi |
| 18 | Ukugqithisatage |
| 19 | Ukuzibandakanyatage |
| 23 | Ipharamitha ayikho kuluhlu |
| 24 | Igalelo B uhambo |
| 26 | Ilahleko yesigaba se-L1 |
| 27 | Ilahleko yesigaba se-L2 |
| 28 | Ilahleko yesigaba se-L3 |
| 29 | I-L1-T1 imfutshane |
| 30 | I-L2-T2 imfutshane |
| 31 | I-L3-T3 imfutshane |
| 33 | Ixesha-overcurrent (bypass overload) |
| 34 | Ubushushu obugqithisileyo be-SCR |
| 35 | Ibhetri/iwotshi |
| 36 | Isekethe ye-Thermistor |
| 47 | Ukongamela |
| 48 | Ngaphantsi kwamandla |
| Ikhowudi | Inkcazo |
| 56 | I-LCP iqhawulwe |
| 57 | Ukubona isantya esingu-zero |
| 58 | I-SCR yayo |
| 59 | Ugqithiso lwangoko nangoko |
| 60 | Umthamo wokukala |
| 70 | Impazamo yokufunda ngoku L1 |
| 71 | Impazamo yokufunda ngoku L2 |
| 72 | Impazamo yokufunda ngoku L3 |
| 73 | Susa ii-volts ezingundoqo (ii-mains voltage iqhagamshelwe kwindlela yokulinganisa) |
| 74 | Uqhagamshelo lweMoto T1 |
| 75 | Uqhagamshelo lweMoto T2 |
| 76 | Uqhagamshelo lweMoto T3 |
| 77 | Ukudubula kusilele P1 |
| 78 | Ukudubula kusilele P2 |
| 79 | Ukudubula kusilele P3 |
| 80 | I-VZC iyasilela kwi-P1 |
| 81 | I-VZC iyasilela kwi-P2 |
| 82 | I-VZC iyasilela kwi-P3 |
| 83 | Iivolthi eziphantsi zolawulo |
| 84–96 | Impazamo yangaphakathi x. Qhagamshelana nomthengisi wasekuhlaleni ngekhowudi yempazamo (x). |
Iikhowudi zemposiso ze-Modbus
| Ikhowudi | Inkcazo | Example |
| 1 | Ikhowudi yokusebenza engekho mthethweni | Iadaptha okanye isiqalisi esithambileyo asiwuxhasi umsebenzi oceliweyo. |
| 2 | Idilesi yedatha engekho mthethweni | Iadaptha okanye isiqalisi esithambileyo asiyixhasi idilesi yerejista echaziweyo. |
| 3 | Ixabiso ledatha engekho mthethweni | I-adapter okanye i-soft starter ayixhasi i-1 yamaxabiso edatha efunyenweyo. |
| 4 | Impazamo yesixhobo sobukhoboka | Kwenzeke imposiso ngexesha uzama ukwenza umsebenzi oceliweyo. |
| 6 | Isixhobo sekhoboka sixakekile | Iadaptha ixakekile (umzekeloample yokubhala iiparamitha kwisiqalisi esithambileyo). |
Ukukhuselwa kweFault Fault
Ngaphezuluview
ISAZISO Ukukhuselwa kwempazamo ephantsi kufumaneka kuphela kumakhadi okhetho anikwe amandla aphantsi aneziqalo ezithambileyo ezisebenzisa uguqulelo oluhambelanayo lwesoftware. Qhagamshelana nomboneleli ngoncedo.
Ikhadi le-Modbus RTU liyakwazi ukubona umhlaba wangoku kunye nohambo ngaphambi kokuba izixhobo zonakaliswe.
Ukukhuselwa kwempazamo ephantsi kufuna i-1000: 1 okanye i-2000: i-1 yangoku i-transformer (ayinikezelwanga). I-CT kufuneka inikwe i-1 VA okanye i-5 VA. Isiqalisi esithambileyo singamiselwa ukuba sihambe ngo-1–50 A. Ukuba impazamo esemhlabeni inyuka ngaphezu kwe-50 A, isiqalisi esithambileyo sihamba ngoko nangoko.
IParameter 40-3 Uhambo lweFault Trip olusebenzayo lukhetha xa ukhuseleko lomhlaba lusebenza.
Qhagamshela i-CT kwi-Ground Fault Inputs
Ukusebenzisa ukukhuselwa kwesiphambeko somhlaba, i-transformer yangoku eqhelekileyo (CT) kufuneka ifakwe kuzo zonke izigaba ze-3.
Inkqubo
Sebenzisa i-1000: 1 okanye i-2000: i-1 CT enomlinganiselo we-1 VA okanye i-5 VA.
Cwangcisa iparameter 40-5 Ground Fault CT ratio ukuze utshatise iCT.
Xhuma i-CT kwii-terminal fault terminals (G1, G2, G3).
Ukukhusela ubuninzi, i-CT kufuneka ifakwe kwicala lokufaka i-soft starter.
Qwalasela iiSetingi zoKhuseleko lweFault
Izicwangciso zokukhusela iziphene zomhlaba kufuneka zisetwe kwisiqalisi esithambileyo.
| Ipharamitha | Inkcazo |
| Ipharamitha 40-1 Umhlaba Impazamo Inqanaba | Iseta indawo yohambo yokhuseleko lwempazamo emhlabeni. |
| Ipharamitha 40-2 Umhlaba Impazamo Ukulibazisa | Ibonisa impendulo yeKhadi le-Modbus RTU kwinguqu yempazamo yomhlaba, ukuphepha iihambo ngenxa yokuguquguquka okwethutyana. |
| Ipharamitha 40-3 Umhlaba Impazamo Uhambo Iyasebenza | Ikhetha xa uhambo oluphantsi komhlaba lunokwenzeka. |
| Ipharamitha 40-4 Umhlaba Impazamo Isenzo | Ikhetha impendulo yesiqalisi esithambileyo kumsitho wokhuselo. |
| Ipharamitha 40-5 Umhlaba Impazamo CT Umlinganiselo | Misela ukutshatisa umlinganiselo we-CT yokulinganisa yangoku. |
Iinkcukacha
Uqhagamshelwano
- Umqali othambileyo we-6-way pin assembly
- Inethiwekhi ye-5-indlela yendoda kunye nesiqhagamshelo sabasetyhini esingaxhumekiyo (sinikezelwe)
- Obona bukhulu besayizi yentambo 2.5 mm2 (14 AWG)
Iisetingi
- Iprotokholi ye-Modbus RTU, i-AP ASCII
- Uluhlu lweedilesi 0–254
- Ireyithi yedatha (bps) 4800, 9600, 19200, 38400
- I-Parity None, Odd, Even, 10-bit
- Ixesha lokuvala Akukho (Cimile), 10 s, 60 s, 100 s
Isiqinisekiso
- I-RCM IEC 60947-4-2
- CE EN 60947-4-2
- I-RoHS ithobela uMyalelo we-EU 2011/65/EU
Danfoss A/S
Ulsnaes 1
DK-6300 Graasten
vlt-drives.danfoss.com
UDanfoss akanakwamkela uxanduva ngeempazamo ezinokwenzeka kwiikhathalogu, iincwadana, kunye nezinye izinto ezishicilelweyo. I-Danfoss inelungelo lokutshintsha iimveliso zayo ngaphandle kwesaziso. Oku kusebenza nakwiimveliso esele zicwangciswe ngokuxhomekeke ekubeni olo tshintsho lunokwenziwa ngaphandle kotshintsho olulandelayo oluyimfuneko kwiinkcukacha esele kuvunyelwene ngazo. Zonke iimpawu zokuthengisa kule mpahla ziyipropathi yeenkampani ezifanelekileyo. I-Danfoss kunye ne-logotype ye-Danfoss ziimpawu zorhwebo zikaDanfoss A/S. Onke Amalungelo Agciniwe.
Amaxwebhu / Izibonelelo
 |
Danfoss VLT Soft Starter MCD600 Modbus RTU Card [pdf] Isikhokelo soFakelo VLT Soft Starter MCD600 Modbus RTU Card, VLT Soft Starter MCD600, Modbus RTU Card, RTU Card, Card |