I-ARDUINO RFLINK-Dibanisa i-UART engenazingcingo kwi-IO Module
I-RFLINK-Mix Wireless UART-to-IO yimodyuli ekulula ukuyisebenzisa evumela abasebenzisi ukuba bamise ngokukhawuleza izixhobo ze-IO ezikude. Awudingi ukuseta iintambo ezininzi ezinde njengoko i-IO suite isenza, kufuneka kuphela ukudibanisa ibhodi ye-UART ROOT ye-RFLINL-Mix kwi-master board (Arduino, Raspberry Pi, nayiphi na enye i-HOST), kunye ne-IO. ibhodi yesixhobo ye-RFLINK-Xuba kwizixhobo ze-IO, emva koko inkqubo ye-IO engenazingcingo ilungele ukuhamba. Ibhodi nganye yesixhobo se-IO ineseti ezi-3 zezibuko le-IO , ngoko ke i-1-to-4 RFLINK-Mix UART ukuya kwi-IO suite inokulawula iiseti ezili-12 ze-IO port.
Inkangeleko yemodyuli kunye nobukhulu
I-RFLINK-Mix UART-to-IO imodyuli iqulethe inxalenye yesiphelo se-UART ROOT (ngasekhohlo). Ukuya kuthi ga kwizixhobo ezine ze-IO (icala lasekunene lomzobo ongezantsi, inombolo 0 ukuya ku-3), zombini Nangona ukubonakala kufana, kunokuchongwa ngeleyibhile esemva kwe-ROOT okanye ISIXHOBO Khangela ibhokisi ukuchonga.
Njengoko kubonisiwe kumzobo ongezantsi, umzobo osekhohlo licala lenxalenye, kwaye ezinye ziyinxalenye yeleyibhile Idilesi yeQela yeli qela leemodyuli zeRFLINK-UARTROOT yi-0001, i-Baud rate 19200. RFLINK I2C Devices as Device 0, Icebo 1, Isixhobo 2, isixhobo sesi-3, idilesi yeQela ngu-0003
Iimpawu zemodyuli
- Ukusebenza ivoltage: 3.3 ~ 5.5V
- RF Frequency: 2400MHz ~ 2480MHz.
- Ukusetyenziswa kwamandla: Ukuhambisa malunga ne-24 mA@ +5dBm kwaye ufumana malunga ne-23mA.
- Amandla okuhambisa: +5dBm
- Umgama wothumelo: malunga ne-80 ukuya kwi-100m kwindawo evulekileyo
- Ireyithi yeBaud(UART ROOT):9,600bps or19,200bps
- Ubungakanani: 25 mm x 15 mm x 2 mm (LxWxH)
- Udibaniso lwe-1 ukuya ku-1 okanye i-1-ukuya-maninzi (ukuya kuthi ga kwezine) Iimodyuli zeDivaysi ze-IO zixhaswa ukuya kumaqela ali-12 i-IO, i-1-ukuya-abaninzi basebenzise kwimo yomyalelo kunye nomyalelo wokukhetha ukuba yeyiphi iModyuli yeSixhobo oza kudlulisa ngayo. .
Inkcazo yenkcazo
| UART ROOT
|
IO ISIXHOBO
|
| GNDè Umhlaba +5Vkwaye 5V voltagIgalelo I-TXè ihambelana ne-RX ye-motherboard ye-UART I-RXè ihambelana ne-TX ye-motherboard ye-UART I-CEBè I-PIN IFUNA imodyuli esezantsi (GND) ukuze isebenze umbane kwaye ingasetyenziswa njengomsebenzi wolawulo wokugcina amandla. PHUMAè I-Pin yokuThunyela ngaphandle kwe-IO kwiZibuko (Ivuliwe/Icimile uThunyelo ngaphandle) èI-pin yegalelo le-IN IO Port (Vuliwe/Valiwe fumana). CMD_Imowudiè I-ROOT yeqhosha lokuqalisa lemo yomyalelo, esebenzayo ephantsi |
GNDè Umhlaba +5Vkwaye 5V voltagIgalelo IN0è I-Input pin (Vula/Vala ukufumana) kwiqela 0 IO Ports NGOKUPHELELEYOè IQela 0 I-IO Port yePin yokuThumela ngaphandle (Ivuliwe/Icimile uThunyelo ngaphandle) IN1è I-Input pin (Vula/Vala ukufumana) kwiqela 1 IO Ports NGOKUPHELELEYOè Cwangcisa iPin yokuThumela ngaphandle kwe-IO yesiZibu esi-1 (Ivuliwe/Icimile Ukuthunyelwa ngaphandle) IN2è I-Input pin (Vula/Vala ukufumana) kwiqela 2 IO Ports NGOKUPHELELEYOè IQela 2 I-IO Port yePin yokuThumela ngaphandle (Ivuliwe/Icimile uThunyelo ngaphandle) I-CEBè I-PIN IFUNA imodyuli esezantsi (GND) ukuze isebenze umbane kwaye ingasetyenziswa njengolawulo lokugcina amandla. umsebenzi. |
Kusetyenziswa kwanjani
Ungasebenzisa le modyuli RFLINK-Dibanisa i-UART-ukuya-IO ukulawula iiseti ezininzi zokuhanjiswa ukuphumeza ulawulo oluzenzekelayo olungenazingcingo.
RFLINK-Dibanisa UART-to-IO ukusetyenziswa examples inokukhutshelwa kwigosa webindawo http://www.sunplusit.com/TW/Shop/IoT/Document.
Amaxwebhu / Izibonelelo
 |
I-ARDUINO RFLINK-Dibanisa i-UART engenazingcingo kwi-IO Module [pdf] Incwadi yokusebenzisa I-RFLINK-Mix, i-UART engenazingcingo ukuya kwiModyuli ye-IO, i-RFLINK-Dibanisa i-UART engenazingcingo kwi-IO Module |
