Imixholo
fihla
I-ARDUINO DHT11 Starter Kit
Iinkcukacha
- Isifundo 1: Inkqubo yokugcinwa kwe-EEPROM
- Isifundo 2: I-0.96in yeNkqubo yeSkrini se-LED
- Isifundo 3: MPU6050 Inkqubo yeGyroscope ye-Six-Axis
- Isifundo 4: Inkqubo ye-Passive Buzzer
- Isifundo 5: Inkqubo ye-DH11 yoBubushushu kunye nokuThuma
- Isifundo 6: Inkqubo yoKwamkela iRemote ye-infrared
- Isifundo 7: Inkqubo yePhotoresistor
Ukugcinwa kwe-LED kunye neNkqubo yeSkrini
Isifundo 1:Inkqubo yoGcino ye-EEPROM:
- Cofa i-Sketch kwi-Arduino IDE, khetha uLawula iThala leencwadi kwiThala leencwadi, khangela i-AT24C256_library, kwaye nqakraza Faka.
- Cofa File kwi Arduino IDE, kwaye ukhethe read_wirte in AT24C256_library ukusuka Examples.
- Cofa Layisha, kwaye nqakraza Monitor Uthotho kwikona ephezulu ngasekunene kwe IDE.
Isifundo 2: I-0.96in yeNkqubo yeSkrini se-LED:
- Cofa i-Sketch kwi-Arduino IDE, khetha uLawula iThala leeNcwadi kwiThala leencwadi, khangela i-U8glib, khetha i-U8glib kwaye ucofe Faka
- Cofa File kwi-Arduino IDE kwaye ukhethe i-FPS ukusuka kwi-U8glib kwi-Eksamples.
- Fumana / / U8GLIB_SSD1306_128X64 u8g (U8G_I2C_OPT_NONE | U8G_I2C_OPT_DEV_0); // I2C/TWI ikhowudi, cima "//" uncomment, cofa ukulayisha kwikona ephezulu ngasekhohlo.
- Fumana / / U8GLIB_SSD1306_128X64 u8g (U8G_I2C_OPT_NONE | U8G_I2C_OPT_DEV_0); // I2C/TWI ikhowudi, cima "//" uncomment, cofa ukulayisha kwikona ephezulu ngasekhohlo.
Isifundo 3: Inkqubo ye-MPU6050 ye-Six-Axis Gyroscope:
- Cofa i-Sketch kwi-Arduino IDE, khetha uLawula iThala leeNcwadi kwiThala leencwadi, khangela i-Adafruit_MPU6050, kwaye ucofe Faka.
- Cofa File kwiArduino IDE kwaye ukhethe basic_readings kwi Adafruit_MPU6050 kwi Eksamples.
- Cofa ku-Layisha, cofa i-Monitor ye-Serial kwikona ephezulu ngasekunene ye-IDE, kwaye utshintshe ukusuka ku-9600baud ukuya kwi-115200baud.
- Kuba amaxabiso okuqala azo zonke ii-axes zeMPU-6050 akanako ukungqinelana, xa i-Acceleration's X kunye ne-Y axes zingalingani no-0 m/^2 kunye no-Z azilingani no-9.8 m/^2, kunye no-X, Y no-Z. yoJikelezo alulingani no0rad/s, unganyusa okanye unciphise amaxabiso emposiso ngeprogram. Yenza ixabiso lokuqala lemveliso lichaneke noko.
Inkqubo ye-Passive Buzzer
Isifundo 4: Inkqubo ye-Passive Buzzer:
Inkqubo yoVavanyo lobushushu kunye nokufuma
Isifundo 5: Inkqubo ye-DH11 yoBubushushu kunye neNkqubo yokuFumana:
- Cofa i-Sketch kwi-Arduino IDE, khetha uLawula iThala leeNcwadi kwiThala leencwadi, khangela i-DHT11, khetha i-DFRobot_DHT11, kwaye ucofe Faka.
- Cofa File kwiArduino IDE, kwaye ukhethe readDHT11 kwi DFRRobot_DHT11 kwi Examples.
- Tshintsha #define DHT11_PIN 10 ukuya #define DHT11_PIN3 kwaye ucofe IDE iphepha lasekhaya Layisha.
- Cofa uthotho Monitor kwikona ephezulu ngasekunene ye-IDE kwaye utshintshe 9600baud ukuya 115200baud. Linda malunga ne-1S ukufumana ubushushu obukhoyo kunye nokufuma.
Inkqubo yoKwamkela iRemote ye-infrared
Isifundo 6: Inkqubo yoKwamkela iRemote ye-infrared
- Cofa i-Sketch kwi-Arduino IDE, khetha uLawula iThala leencwadi kwiThala leencwadi, khangela i-IRremote, kwaye nqakraza Faka.
- Cofa File kwiArduino IDE kwaye ukhethe ReceiveDemo ukusuka IRremote kwi Examples.
- Cofa ku-Layisha, cofa i-Monitor ye-Serial kwikona ephezulu ngasekunene ye-IDE, kwaye utshintshe ukusuka ku-9600baud ukuya kwi-115200baud. Sebenzisa isilawuli kude esihambelanayo ukulungelelanisa imodyuli yokufumana infrared kwaye ucinezele naliphi na iqhosha. Xa idatha ehambelanayo ibonakala, imodyuli iya kusebenza ngokuqhelekileyo.
Isifundo 7: Inkqubo yeFotoresistor:
Isifundo 8: Inkqubo yeqhosha:
FAQ
Umbuzo osoloko ubuzwas
- Umbuzo: Ndiyicombulula njani ingxaki ukuba inkqubo yam ayisebenzi?
- A: Jonga imidibaniso ukuqinisekisa ukuba imiselwe ngokufanelekileyo. Qinisekisa ukuba amathala eencwadi afakwe ngokuchanekileyo kwi-Arduino IDE. Qinisekisa ukuba ikhowudi ayinazimpazamo kwaye ihambelana nemiyalelo enikwe kwincwadana.
Amaxwebhu / Izibonelelo
 |
I-ARDUINO DHT11 Starter Kit [pdf] Isikhokelo somsebenzisi DHT11, DHT11 Kit yokuQalisa, iKit yokuQalisa, iKit |