Allen-Bradley POINT I/O 4 Isitishi esiPhezulu soXinano oluPhezulu lwangoku lweMiyalelo yeeModyuli zokuNgenisa
I-POINT I/O 4 Isitishi esiPhezulu soXinano oluPhezulu lwangoku lweMiyalelo yokuFakela iModyuli
QAPHELA: Funda olu xwebhu kunye namaxwebhu adweliswe kwicandelo leZibonelelo ezongezelelweyo malunga nofakelo, ulungelelwaniso kunye nokusebenza kwesi sixhobo phambi kokuba ufake, uqwalasele, usebenze okanye ugcine le mveliso. Abasebenzisi kufuneka baziqhelanise nemiyalelo yokufakela kunye neengcingo ukongeza kwiimfuno zazo zonke iikhowudi ezisebenzayo, imithetho kunye nemigangatho.
Imisebenzi ebandakanya ukufakela, uhlengahlengiso, ukufakwa kwinkonzo, ukusetyenziswa, ukudibanisa, ukudiliza, kunye nokugcinwa kufuneka kuqhutywe ngabasebenzi abaqeqeshwe ngokufanelekileyo ngokuhambelana nekhowudi yokusebenza esebenzayo. Ukuba esi sixhobo sisetyenziswa ngendlela engachazwanga ngumenzi, ukhuseleko olunikezelwa sisixhobo lunokonakala.
Indalo kunye neNdawo
QAPHELA: Esi sixhobo senzelwe ukusetyenziswa kwindawo yemveliso yePollution Degree 2, kwi-overvoltage Uluhlu lwezicelo ze-II (njengoko kuchaziwe kwi-EN / IEC 60664-1), kwiindawo eziphakamileyo ukuya kwi-2000 m (6562 ft) ngaphandle kokunciphisa.
Esi sixhobo asenzelwanga ukusetyenziswa kwindawo yokuhlala kwaye asinakubonelela ngokhuseleko olululo kwiinkonzo zonxibelelwano lukanomathotholo kwiindawo ezinjalo.
Esi sixhobo sinikezelwa njengezixhobo ezivulekileyo zokusetyenziswa ngaphakathi. Kufuneka ixhonywe ngaphakathi kwendawo ebiyelweyo eyilelwe ngokufanelekileyo ezo meko zokusingqongileyo ezikhethekileyo eziya kubakho kwaye ziyilelwe ngokufanelekileyo ukuthintela ukwenzakala komntu ngenxa yokufikeleleka kwiindawo eziphilayo. Indawo ebiyelweyo kufuneka ibe neendawo ezifanelekileyo zokunqanda amadangatye ukuthintela okanye ukunciphisa ukusasazeka kwedangatye, ukuthobela umlinganiselo wokusasazeka komlilo we-5VA okanye uvunyiwe kwisicelo ukuba awukho ngentsimbi. Ingaphakathi le-enclosure kufuneka ifikeleleke kuphela ngokusetyenziswa kwesixhobo. Amacandelo alandelayo olu papasho anokuthi aqulathe ulwazi oluthe kratya malunga nohlobo oluthile lokulinganisa olufunekayo ukuthobela iziqinisekiso ezithile zokhuseleko lwemveliso.
Ukongeza kolu papasho, bona oku kulandelayo:
- I-Industrial Automation Wiring and Grounding Guidelines, ukupapashwa kwe-1770-4.1, kwiimfuno ezingaphezulu zofakelo.
- Umgangatho we-NEMA we-250 kunye ne-EN/IEC 60529, njengoko kufanelekile, kwiinkcazo zeedigri zokukhusela ezibonelelwa ngee-enclosures.
Ukuthintela ukukhutshwa kwe-Electrostatic Discharge
QAPHELA: Esi sixhobo sinovelwano malunga nokukhutshwa kwe-electrostatic, okunokubangela umonakalo wangaphakathi kwaye kuchaphazele ukusebenza okuqhelekileyo. Landela ezi zikhokelo xa uphethe esi sixhobo:
- Chukumisa into esekelwe phantsi ukuze ukhuphe into engatshintshiyo.
- Nxiba umtya wesihlahla osezantsi ovunyiweyo.
- Musa ukubamba izihlanganisi okanye izikhonkwane kwiibhodi zamacandelo.
- Musa ukubamba amacandelo esekethe ngaphakathi kwesixhobo.
- Sebenzisa indawo yokusebenza emileyo-ekhuselekileyo, ukuba ikhona.
- Gcina izixhobo kwipakethe efanelekileyo engatshintshiyo xa ingasetyenziswa.
Imvume yaseMntla Melika yendawo enobungozi
Olu lwazi lulandelayo lusebenza xa usebenzisa esi sixhobo kwiindawo eziyingozi.
Iimveliso eziphawulwe "CL I, DIV 2, GP A, B, C, D" zifanelekile ukusetyenziswa kwiKlasi I Division 2 Amaqela A, B, C, D, Iindawo ezinobungozi kunye neendawo ezingenabungozi kuphela. Imveliso nganye ineziphawulo kwi-nameplate yokukala ebonisa ikhowudi yobushushu bendawo enobungozi. Xa udibanisa iimveliso ngaphakathi kwenkqubo, ikhowudi yeqondo lokushisa elibi kakhulu (inombolo ephantsi "i-T") ingasetyenziselwa ukukunceda ukucacisa ikhowudi yeqondo lokushisa jikelele. Ukudityaniswa kwezixhobo kwisixokelelwano sakho kuxhomekeke kuphando nguGunyaziwe wengingqi Onolawulo ngexesha lofakelo.
ISILUMKISO:
Ingozi yokudubula -
- Musa ukuqhawula izixhobo ngaphandle kokuba umbane ususiwe okanye indawo yaziwa njengengenabungozi.
- Musa ukuqhawula uqhagamshelo kwesi sixhobo ngaphandle kokuba umbane ususiwe okanye indawo yaziwa njengengenabungozi. Khusela naluphi na uqhagamshelo lwangaphandle oludibana nesi sixhobo ngokusebenzisa izikrufu, iiletshi zokutyibilika, izihlanganisi ezinemisonto, okanye ezinye iindlela ezibonelelwe ngale mveliso.
- Ukutshintshwa kwamacandelo kunokuphazamisa ukufaneleka kweKlasi I, iCandelo 2.
QAPHELA: Ukuthobela izithintelo ze-UL, amandla entsimi kunye nazo zonke izixhobo eziqhagamshelweyo kufuneka zinikwe amandla ukusuka kumthombo omnye ngokuthobela oku kulandelayo: Udidi 2
I-UK kunye neYurophu yokuVunywa kwendawo enobungozi
Oku kulandelayo kusebenza kwiimveliso eziphawulwe II 3 G:
- Zenzelwe ukusetyenziswa kwiindawo ezinokuthi zibe noqhushumbo njengoko kuchaziwe ngummiselo we-UKEX 2016 No. 1107 kunye ne-European Union Directive 2014/34/EU kwaye kufunyaniswe ukuthobela iiMfuno eziBalulekileyo zeMpilo kunye noKhuseleko ngokunxulumene noyilo kunye nokwakhiwa kwezixhobo zeCandelo 3 ukuze zisetyenziswe kuZowuni 2 umoya onokuba noqhushumbo, onikwe kwiShedyuli 1 ye-UKEX kunye neSihlomelo II salo Myalelo.
- Ukuthotyelwa kweeMfuno eziBalulekileyo zeMpilo kunye noKhuseleko kuye kwaqinisekiswa ngokuthotyelwa kwe-EN IEC 60079-7, kunye ne-EN IEC 60079-0.
- Ngaba iQela leZixhobo ze-II, iCandelo leZixhobo 3, kwaye lithobela iiMfuno eziBalulekileyo zeMpilo kunye noKhuseleko olunxulumene noyilo kunye nokwakhiwa kwezixhobo ezinjalo ezinikwe kwiShedyuli 1 ye-UKEX kunye neSihlomelo II se-EU Directive 2014/34/EU. Jonga i-UKEx kunye ne-EU Declaration of Conformity kwi-rok.auto/certifications ngeenkcukacha.
- Uhlobo lokhuselo luyi-Ex ec IIC T4 Gc ngokwe-EN IEC 60079-0: 2018, I-ATMOSPHERES EZIQHUMAYO - INXALENYE 0: IZIXHOBO - IIMFUNO EZIQHELEKILEYO, Umhla wokukhutshwa kwe-07/2018, kunye ne-CENELEC EN IEC 60079 + 7: 2015:1 2018:XNUMX , Imimoya eqhumayo. Ukukhuselwa kwezixhobo ngokunyuka kokhuseleko "e".
- Ukuthobela uMgangatho we-EN IEC 60079-0: 2018, I-ATMOSPHERES EZIQHUBEKAYO - INXALENYE 0: IZIXHOBO - IIMFUNO EZIQHELEKILEYO, Ukukhutshwa komhla we-07/2018, kunye ne-CENELEC EN IEC 60079- 7: 2015 + A1:2018 i-Explosives. Ukukhuselwa kwezixhobo ngokunyuka kokhuseleko "e", inombolo yesiqinisekiso sereferensi DEMKO 04 ATEX 0330347X kunye ne-UL22UKEX2478X.
- Zilungiselelwe ukusetyenziswa kwiindawo apho imimoya eqhumayo ebangelwa ziigesi, umphunga, inkungu, okanye umoya kungalindelekanga ukuba yenzeke, okanye enokwenzeka kuphela ngamaxesha athile kunye namaxesha amafutshane. Iindawo ezinjalo zihambelana nokuhlelwa kweZone 2 ngokomgaqo we-UKEX 2016 No. 1107 kunye nomyalelo we-ATEX 2014/34/EU.
- Isenokuba neenombolo zekhathalogu elandelwa ngu-“K” ukubonisa ukhetho lokwaleka oluhambelanayo.
Ukwamkelwa kweNdawo enobungozi ye-IEC
Oku kulandelayo kusebenza kwiimveliso ezinesatifikethi se-IECEx:
- Zilungiselelwe ukusetyenziswa kwiindawo apho imimoya eqhumayo ebangelwa ziigesi, umphunga, inkungu, okanye umoya kungalindelekanga ukuba yenzeke, okanye enokwenzeka kuphela ngamaxesha athile kunye namaxesha amafutshane. Iindawo ezinjalo zihambelana nokuhlelwa kweZone 2 kwi-IEC 60079-0.
- Uhlobo lokhuseleko yi-Ex eC IIC T4 Gc ngokwe-IEC 60079-0 kunye ne-IEC 60079-7.
- Ukuthobela iMigangatho ye-IEC 60079-0, imimoya eqhumayo - Icandelo le-0: Izixhobo - Iimfuno ngokubanzi, uHlelo 7, uHlaziyo lomhla we-2017 kunye ne-IEC 60079-7, i-5.1 yoHlelo lokuhlaziya umhla we-2017, Imimoya eqhumayo - iSigaba 7: Ukhuseleko lwezixhobo ngokhuseleko olongeziweyo "e ”, inombolo yesiqinisekiso se-IECEx ye-IECEx UL 20.0072X.
- Isenokuba neenombolo zekhathalogu elandelwa ngu-“K” ukubonisa ukhetho lokwaleka oluhambelanayo.
ISILUMKISO:
- Esi sixhobo siya kusetyenziswa phakathi kweereyithingi ezichaziweyo ezichazwe yiRockwell Automation.
- Khusela naluphi na uqhagamshelo lwangaphandle oludibana nesi sixhobo ngokusebenzisa izikrufu, iiletshi zokutyibilika, izihlanganisi ezinemisonto, okanye ezinye iindlela ezibonelelwe ngale mveliso.
- Musa ukuqhawula izixhobo ngaphandle kokuba umbane ususiwe okanye indawo yaziwa njengengenabungozi.
QAPHELA:
- Esi sixhobo asikwazi ukumelana nokukhanya kwelanga okanye eminye imithombo yemitha ye-UV.
- Ukuba esi sixhobo sisetyenziswe ngendlela engachazwanga ngumvelisi, ukhuselo olunikezelwa sisixhobo lunokuphazamiseka.
Imiqathango ekhethekileyo yokusetyenziswa ngokukhuselekileyo
ISILUMKISO:
- Esi sixhobo siya kuxhonywa kwindawo evalelweyo eqinisekisiweyo yase-UKEX/ATEX/IECEx Zone 2 kunye nenqanaba lokhuseleko lokungena ubuncinane le-IP54 (ngokuhambelana ne-EN/IEC 60079-0) kwaye isetyenziswe kwindawo engekho ngaphezu kwe-Pollution Degree 2 ( njengoko kuchaziwe kwi-EN/IEC 60664-1) xa isetyenziswa kwindawo yeZone 2. Indawo ebiyelweyo kufuneka ifikeleleke kuphela ngokusetyenziswa kwesixhobo.
- Ukhuseleko oludlulayo luya kunikezelwa olubekwe kwinqanaba elingagqithiyo kwi-140% yomthamo ophakathitage kwiitheminali zokubonelela kwisixhobo.
- Esi sixhobo kufuneka sisetyenziswe kuphela nge-UKEX/ATEX/IECEx eqinisekisiweyo ye-Rockwell Automation backplanes.
- Ukwenziwa komhlaba kufezekiswa ngokunyuswa kweemodyuli kuloliwe.
- Kwimodyuli ye-1734-IE4C, iikhondatha kufuneka zisetyenziswe kunye neqondo lobushushu le-conductor elisezantsi lama-92 °C.
Ngaphambi kokuba Uqale
Le POINT I/O™ series C imveliso ingasetyenziswa noku kulandelayo:
- I-DeviceNet® kunye neeadaptha zePROFIBUS
- Iiadaptha ze-ControlNet® kunye ne-EtherNet/IP™, zisebenzisa i-Studio 5000 Logix Designer® application version 20 okanye kamva Bona uMfanekiso 1 kunye noMzobo 2 ukuze uziqhelanise neendawo ezinkulu zemodyuli, uqaphele ukuba i-wiring base assembly yenye yezi zilandelayo:
- I-1734-TB okanye i-1734-TBS POINT I/O isiseko se-terminal enamacandelo amabini, ebandakanya ibhloko ye-terminal esusekayo ye-1734-RTB kunye ne-1734-MB isiseko sokunyuka.
- I-1734-TOP okanye i-1734-TOPS POINT I/O isiseko se-terminal yesiqhekeza
Umzobo 1 – POINT I/O 4 Ijelo leModyuli yoNgeniso oluPhezulu-Uxinano oluPhezulu lwangoku olune-1734-TB okanye i-1734-TBS Base
| Inkcazo | Inkcazo | ||
| 1 | Indlela yokutshixa imodyuli | 6 | I-1734-TB, i-1734-TBS isiseko sokuxhoma |
| 2 | Ileyibhile yesilayidi-ngaphakathi ebhalwe | 7 | Iziqwenga zecala ezidibeneyo |
| 3 | Imodyuli ye-I/O efakweyo | 8 | Isitshixo sikamatshini (orenji) |
| 4 | Ibhloko yeterminal esusekayo (RTB) isiphatho | 9 | I-DIN kaloliwe yokutshixa isikrufu (orenji) |
| 5 | I-RTB ene-screw okanye i-spring clamp | 10 | Umzobo wocingo lwemodyuli |
Umzobo we-2 - I-POINT I / O 4 I-Channel High-Density Current Input Module kunye ne-1734-TOP okanye i-1734-TOPS Base
| Inkcazo | Inkcazo | ||
| 1 | Indlela yokutshixa imodyuli | 6 | Iziqwenga zecala ezidibeneyo |
| 2 | Ileyibhile yesilayidi-ngaphakathi ebhalwe | 7 | Isitshixo sikamatshini (orenji) |
| 3 | Imodyuli ye-I/O efakweyo | 8 | I-DIN kaloliwe yokutshixa isikrufu (orenji) |
| 4 | Ibhloko yeterminal esusekayo (RTB) isiphatho | 9 | Umzobo wocingo lwemodyuli |
Faka isiseko sokuNzeka
Ukufakela isiseko sokunyuka kwi-DIN kaloliwe (i-Allen-Bradley® inxalenye yenombolo 199-DR1; 46277-3; EN50022), qhubeka ngolu hlobo lulandelayo:
QAPHELA: Le mveliso isekelwe kwi-DIN kaloliwe ukuya kumhlaba we-chassis. Sebenzisa i-zinc-plated chromate passivated steel DIN kaloliwe ukuze uqinisekise umhlaba ofanelekileyo. Ukusetyenziswa kwezinye izixhobo zikaloliwe zeDIN (umzekeloample, i-aluminiyam okanye iplastiki) ezinokugqwesa, i-oxidize, okanye i-conductors engalunganga, inokubangela ukumisa okungafanelekanga okanye okwethutyana. Khusela isiporo se-DIN kwindawo yokunyusela malunga ne-200 mm nganye (7.8 in.) kwaye usebenzise iiankile zokuphela ngokufanelekileyo. Qinisekisa ukuba umisa isiporo seDIN ngokufanelekileyo. Jonga i-Industrial Automation Wiring kunye neziKhokelo zokuGrounding, ukupapashwa kwe-1770-4.1, ngolwazi olungakumbi.
- Misa isiseko sokuxhoma ngokuthe nkqo ngaphezu kweeyunithi ezifakelweyo (i-adaptha, unikezelo lwamandla okanye imodyuli ekhoyo).
- Slayida isiseko sokuxhoma ezantsi uvumela amaqhekeza asecaleni adibanayo ukuba abandakanye imodyuli esecaleni okanye iadaptha.
- Cinezela ngokuqinileyo ukuhlalisa isiseko sokunyusela kuloliwe weDIN. Isiseko sokuxhoma singena endaweni.
- Ukususa isiseko sokunyuka kwi-DIN kaloliwe, susa imodyuli, kwaye usebenzise i-screwdriver encinci ye-bladed ukujikeleza i-screw yokutshixa isiseko kwindawo ethe nkqo. Oku kukhulula indlela yokutshixa. Emva koko phakamisa ngqo phezulu ukususa.
Faka iModyuli
Imodyuli inokufakwa ngaphambi okanye emva kofakelo lwesiseko. Qinisekisa ukuba isiseko sokunyuswa sifakwe ngokuchanekileyo isitshixo phambi kokufaka imodyuli kwisiseko sokunyuka. Ukongeza, qiniseka ukuba isikrufu sokutshixa isiseko sibekwe ireferensi ethe tye kwisiseko.
ISILUMKISO: Xa ufaka okanye ususa imodyuli ngelixa amandla e-backplane evuliwe, i-arc yombane ingenzeka. Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo.
Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke. I-arcing yombane ephindaphindiweyo ibangela ukunxiba okugqithisileyo kubafowunelwa kuzo zombini imodyuli kunye nesinxibelelanisi sayo sokukhwelana. Abafowunelwa abagugileyo banokwenza ukunganyangeki kombane okunokuchaphazela ukusebenza kwemodyuli.
- Ukusebenzisa i-screwdriver ene-bladed ukujikelezisa istshitshi yesitshixo kwisiseko sokunyuswa ngokwewotshi de inani elifunekayo kuhlobo lwemodyuli efakelweyo ilungelelaniswa nenotshi kwisiseko.
- Qinisekisa ukuba isikrufu sikaloliwe seDIN sokutshixa sikwindawo ethe tye. Ukuba indlela yokutshixa ivuliwe, awukwazi ukufaka umnqongo.
- Faka imodyuli ngqo ezantsi kwisiseko sokuxhoma kwaye ucinezele ukukhusela. Imodyuli itshixeka endaweni.
NONE
Ibhloko yeSitena esiSukayo (i-RTB) inikezelwe kunye nendibano yakho yesiseko socingo. Ukususa, tsala phezulu kwisiphatho se-RTB. Oku kuvumela isiseko sokuxhoma ukuba sisuswe kwaye sitshintshwe njengoko kuyimfuneko ngaphandle kokususa nayiphi na iingcingo. Ukufaka kwakhona iBhloko yeSitena esiSukayo, qhubeka ngolu hlobo lulandelayo:
- Faka isiphelo ngokuchasene nesiphatho kwiyunithi yesiseko. Esi siphelo sinecandelo eligobileyo elibandakanya isiseko socingo.
- Jikelezisa ibhloko yetheminali kwisiseko socingo de izitshixe endaweni yayo.
- Ukuba imodyuli ye-I/O ifakiwe, cofa isiphatho se-RTB endaweni kwimodyuli.
ISILUMKISO: Xa uqhagamshela okanye uqhawula uqhagamshelo lweSitena esiSukayo (i-RTB) ngokusetyenziswa kombane wecala lentsimi, i-arc yombane inokwenzeka. Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo.
Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke.
ISILUMKISO: Kwi-1734-RTBS kunye ne-1734-RTB3S, ukukhwela kunye nokukhulula ucingo, faka i-screwdriver ene-bladed (inombolo yekhathalogu 1492-N90 - 3 mm ubukhulu beblade) kwindawo yokuvula malunga ne-73 ° (i-blade surface ihambelana nomphezulu wokuvulwa. ) kwaye tyhala phezulu ngobunono.
ISILUMKISO: Kwi-1734-TOPS kunye ne-1734-TOP3S, ukukhwela kunye nokukhupha ucingo, faka i-screwdriver ene-bladed (inombolo yekhathalogu 1492-N90 - 3 mm ububanzi) kwindawo yokuvula malunga ne-97 ° (i-blade surface ihambelana nomphezulu wokuvulwa) kwaye cinezela ngaphakathi (musa ukutyhala phezulu okanye ezantsi).
Susa isiseko sokuNyuka
Ukususa isiseko sokunyuka, kufuneka ususe nayiphi na imodyuli efakiweyo, kunye nemodyuli efakwe kwisiseko ekunene. Susa iBhlokhi yeSitena esiSukayo, ukuba inocingo.
- Khulula isiphatho se-RTB kwimodyuli ye-I/O.
- Tsala umqheba we-RTB ukususa iBloko yeSitena esiSukayo.
- Cinezela isitshixo semodyuli phezulu kwimodyuli.
- Tsala kwimodyuli ye-I/O ukuyisusa kwisiseko.
- Phinda amanyathelo 1, 2, 3 kunye no-4 kwimodyuli esekunene.
- Sebenzisa isikrufu esincinci esinamaphiko ukujikelezisa isikrufu esi-orenji sokutshixa sime nkqo. Oku kukhulula indlela yokutshixa.
- Phakamisa ngqo phezulu ukususa.
Faka isiseko se-1734-TOPS
- Beka isiseko ngokuthe nkqo ngaphezu kweeyunithi ezifakelweyo, ezifana neadaptha, unikezelo lwamandla, okanye imodyuli ekhoyo.
- Slayida isiseko ezantsi, uvumele amaqhekeza ecala adibeneyo ukuba abandakanye iyunithi efakelweyo ekufutshane.
- Cinezela ngokuqinileyo ukuhlalisa isiseko kwi-DIN kaloliwe de isiseko singene endaweni.
- Qinisekisa ukuba isikrufu sikaloliwe se-DIN sokutshixa sikwimo ethe tye, itshixiwe phambi kokufaka imodyuli ye-I/O.
Susa isiseko se-1734-TOPS
- Ukususa isiseko se-wiring kwi-DIN kaloliwe, kufuneka ususe imodyuli efakwe ngasekunene kwesiseko.
- Cofa indlela yokutshixa imodyuli ekunene kwesiseko, utsalela phezulu ukususa imodyuli.
- Jika isikrufu esiorenji sokutshixa sime nkqo ukuze uvule isiseko esisuka kuloliwe weDIN.
- Shelelisela isiseko phezulu ukuyikhulula kwiiyunithi zayo zokukhwelana.
Ucingo lweModyuli
I-Chas Gnd = i-Chassis ground C = Eqhelekileyo
ISILUMKISO: Ukuba uqhagamshela okanye uqhawula iingcingo ngelixa umbane wecala lentsimi uvuliwe, i-arc yombane ingenzeka. Oku kunokubangela uqhushumbo kufakelo oluyingozi kwindawo. Qinisekisa ukuba umbane ususiwe okanye indawo ayinabungozi phambi kokuba uqhubeke.
Umzobo wocingo
(1) 1734-VTM iyakhethwa. Sebenzisa unikezelo lwe-24V DC ukusuka kwimodyuli ye-1734-VTM kwii-2-wire/3-wire devices.
| Umjelo | Igalelo langoku | Eqhelekileyo | Itshisi Umhlaba |
| 0 | 0 | 4 okanye 5 | 6 okanye 7 |
| 1 | 1 | ||
| 2 | 2 | ||
| 3 | 3 |
I-12/24V DC inikezelwa yibhasi yamandla yangaphakathi.
Nxibelelana neModyuli yakho
I-POINT I / O iimodyuli zithumela (zidla) kwaye zifumane (ukuvelisa) idatha ye-I / O (imiyalezo). Ubeka le datha kwimemori yeprosesa.
Le modyuli ye-POINT I / O ivelisa i-12 bytes yedatha yokufaka (i-scanner i-Rx) kunye nedatha yesimo sephutha. Ayisebenzisi idatha ye-I/O (i-scanner Tx).
Imephu yeDatha eMiselweyo ye-1734-IE4C, 1734-IE4CK iModyuli yoNgeniso yeAnalog
Ubungakanani bomyalezo: 12 Bytes
| 15 | 14 | 13 | 12 | 11 | 10 | 09 | 08 | 07 | 06 | 05 | 04 | 03 | 02 | 01 | 00 | |
| Ivelisa (iskena Rx) | Ijelo leNgeniso 0 Ibhayithi ephezulu | Isitishi soNgeniso 0 Ibhayithi ephantsi | ||||||||||||||
| Ijelo leNgeniso 1 Ibhayithi ephezulu | Isitishi soNgeniso 1 Ibhayithi ephantsi | |||||||||||||||
| Ijelo leNgeniso 2 Ibhayithi ephezulu | Isitishi soNgeniso 2 Ibhayithi ephantsi | |||||||||||||||
| Ijelo leNgeniso 3 Ibhayithi ephezulu | Isitishi soNgeniso 3 Ibhayithi ephantsi | |||||||||||||||
| I-Byte yesimo seSiteshi soku-1 | I-Byte yesimo seSiteshi soku-0 | |||||||||||||||
| OR | UR | HHA | LLA | HA | LA | CM | CF | OR | UR | HHA | LLA | HA | LA | CM | CF | |
| I-Byte yesimo seSiteshi soku-3 | I-Byte yesimo seSiteshi soku-2 | |||||||||||||||
| OR | UR | HHA | LLA | HA | LA | CM | CF | OR | UR | HHA | LLA | HA | LA | CM | CF | |
| Iphi = Ubume beFault Channel; 0 = akukho mpazamo, 1 = iimpazamo = Imo yoLungiso; 0 = eqhelekileyo, 1 = imo yokulinganisa LA = I-Alarm ephantsi; 0 = akukho mpazamo, 1 = impazamo = I-Alam ephezulu; 0 = akukho mpazamo, 1 = iphutha LA = I-Alarm ephantsi / ephantsi: 0 = akukho mpazamo, 1 = impazamo HHA = I-Alarm ephezulu / ephezulu; 0 = akukho mpazamo, 1 = impazamo ye-UR = Ingatshintshi; 0 = akukho mpazamo, 1 = impazamo OKANYE = Ukugqithisa; 0 = akukho mpazamo, 1 = impazamo | ||||||||||||||||
| Isebenzisa (iskena Tx) | Akukho datha esetyenzisiweyo | |||||||||||||||
Izalathi zesimo sokutolika
Jonga iSazobe 3 kunye neTheyibhile 1 ngolwazi malunga nendlela yokutolika izikhombisi zobume.
Umzobo 3 – Iimpawu zesimo sePOINT I/O 4 Ijelo leModyuli yoNgeniso oluPhezulu loXinano oluPhezulu lwangoku
- Ubume bemodyuli
- Imo yenethiwekhi
- Ubume begalelo 0
- Ubume begalelo 1
- Ubume begalelo 2
- Ubume begalelo 3
Itheyibhile 1 – Isimo seSalathisi seModyuli
| Isalathisi | Umbuso | Inkcazo |
| Ubume bemodyuli | Cimile | Akukho mandla asetyenziswayo kwisixhobo. |
| Luhlaza | Isixhobo sisebenza ngokwesiqhelo. | |
| Ukudanyaza eluhlaza | Isixhobo sifuna ugunyaziso ngenxa yokungabikho, ukungagqibeki, okanye ulungelelwaniso olungachanekanga. | |
| Ukudanyaza bomvu | Impazamo enokubuyiselwa. | |
| Bomvu | Isiphene esingafumanekiyo sinokufuna ukutshintshwa kwesixhobo. | |
| Ukudanyaza bomvu/luhlaza | Isixhobo sikwimowudi yokuzivavanya. |
ITheyibhile 1-Isimo seSalathisi seModyuli (Iyaqhutywa)
| Isalathisi | Umbuso | Inkcazo |
| Ubume benethiwekhi | Cimile | Isixhobo asikho kwi-intanethi:- Isixhobo asilugqibanga uvavanyo lwe-dup_MAC-id.- Isixhobo asiqhutywanga – jonga isalathisi semodyuli. |
| Ukudanyaza eluhlaza | Isixhobo sikwi-intanethi kodwa akukho qhagamshelwano kwindawo esekiweyo. | |
| Luhlaza | Isixhobo sikwi-intanethi kwaye sinonxibelelwano kwindawo esekiweyo. | |
| Ukudanyaza bomvu | Enye okanye ngaphezulu umdibaniso we-I/O ukwimo yokuphela kwexesha. | |
| Bomvu | Ukusilela kwekhonkco elibalulekileyo - isixhobo sonxibelelwano esingaphumelelanga. Isixhobo sichonge impazamo esithintela ekunxibelelaneni nenethiwekhi. | |
| Ukudanyaza bomvu/luhlaza | Isixhobo esinempazamo kunxibelelwano – isixhobo sifumanise impazamo yofikelelo kuthungelwano kwaye sikwimeko enempazamo kunxibelelwano. Isixhobo sifumene kwaye samkele iSicelo esineFaultity yoNxibelelwano lwesazisi - umyalezo omde weprotocol. | |
| Ubume bejelo | Cimile | Imodyuli kwimo yeCAL. |
| Uhlaza oluqinileyo | Okuqhelekileyo (amagalelo okukhangela itshaneli). | |
| Ukudanyaza eluhlaza | Ijelo liyalungiswa. | |
| Ubomvu oqinileyo | Akukho mandla okanye impazamo enkulu yesitishi. | |
| Ukudanyaza bomvu | Umjelo ekupheleni koluhlu (0 mA okanye 21 mA). |
Iinkcukacha
KUBALULEKILEYO Izinga loHlaziyo loNgeniso kunye nempendulo yeNyathelo ye-1734-IE4C kunye neemodyuli ze-1734-IE4CK zihluke kwiimodyuli zekhathalogu ye-1734-IE2C kunye ne-1734-IE2CK.
IiNgcaciso zeNgeniso
| Uphawu lophawu | Ixabiso |
| Inani lamagalelo | I-4, iphelile enye, ingekho yodwa, yangoku |
| Isigqibo | I-16 bits – ngaphezulu kwe-0…21 mA0.32 µA/cnt |
| Faka i-terminal yangoku | 4…20 mA0…20 mA |
| Ukuchaneka ngokupheleleyo(1) Itheminali yangoku | 0.1% Isikali esiPheleleyo @ 25 °C |
| Ukuchaneka kokuhamba ngesantya. Itheminali yangoku | 30 ppm/°C |
| Ireyithi yohlaziyo lwegalelo, ngokwemodyuli nganye | 240 ms @ Notch = 50 Hz200 ms @ Notch = 60 Hz (emiselweyo) 120 ms @ Inotshi = 100 Hz100 ms @ Notch = 120 Hz 60 ms @ Inotshi = 200 Hz 50 ms @ Notch = 240 ms 40 Hz 300 30 ms @ Notch = 400 Hz 25 ms @ Notch = 480 Hz |
| Impendulo yenyathelo, ngetshaneli nganye | 60 ms @ Notch = 50 Hz50 ms @ Inotshi = 60 Hz (ehlala ikho) 30 ms @ Inotshi = 100 Hz25 ms @ Notch = 120 Hz 15 ms @ Inotshi = 200 Hz12.5 ms @ Inotshi = 240 Hz 10 ms @ Inotshi = 300 Hz 7.5 ms Hz400 ms @ Notch = 6.25 Hz480 ms @ Notch = XNUMX Hz |
| Igalelo lokuthintela/ukumelana | 60 Ω |
| Uhlobo loguqulo | Delta Sigma |
| Umlinganiselo wokulahlwa kwendlela eqhelekileyo | -120 dB |
Iinkcukacha ngegalelo (Iyaqhutywa)
| Uphawu lophawu | Ixabiso |
| Umlinganiselo wokulahlwa kwendlela eqhelekileyo | -60 dBNotch Filter13.1 Hz @ Notch = 50 Hz15.7 Hz @ Notch = 60 Hz (ehlala ikho)26.2 Hz @ Notch = 100 Hz31.4 Hz @ Notch = 120 Hz52.4 Hz @ Notch = 200 Hz @ 62.9 Hz Inotshi = 240 Hz78.6 Hz @ Inotshi = 300 Hz104.8 Hz @ Inotshi = 400 Hz125.7 Hz @ Inotshi = 480 Hz |
| Ifomathi yedatha | Inombolo epheleleyo esayiniweyo |
| Ubuninzi bomthwalo ogqithisiweyo | Impazamo ikhuselwe kwi-28.8V DC |
| Ulungelelwaniso | Umzi-mveliso ulinganisiwe |
| Izalathisi, icala lengqiqo | Imodyuli e-1 eluhlaza/ebomvu 1 imodyuli eluhlaza/ebomvu 4 imodyuli eluhlaza/ebomvu |
(1) Ibandakanya i-offset, inzuzo, i-non-linearity, kunye nemigaqo yempazamo yokuphindaphinda.
KUBALULEKILEYO Jonga i-POINT I / O Modules Selection Guide, ukupapashwa kwe-1734-SG001 ngolwazi malunga nokuphula ibhasi yokuhambisa amandla entsimi. Jonga amacandelo "Xa Usebenzisa i-Field Power Distributor" kunye "nokusebenzisa nini iYunithi yaMandla oKwandiswa".
Iinkcukacha ngokuBanzi
| Uphawu lophawu | Ixabiso |
| Isiseko setheminali | I-1734-TB3, i-1734-TB3S indibano yesiseko socingo |
| POINTBus™ yangoku, ubuninzi | 75 mA |
| Ukutshatyalaliswa kwamandla, ubuninzi | 0.55 W @ 28.8V DC |
| Ukuchithwa kwe-Thermal, max | 2.0 BTU/iyure @ 28.8V DC |
| Ukubonelela ngevoltage, umva | 5V DC |
| Ukubonelela ngevoltaguluhlu lwe-e, igalelo lamandla entsimi | 10…28.8V DC, 20 mA, Udidi 2 |
| Ungeniso lwangoku | 4…20 mA okanye 0…20 mA |
| Ukuzahlula voltage | I-50V, ivavanywe @ 1500V AC ye-60 s, amagalelo, kunye namandla entsimi kwinkqubo Akukho mahluko phakathi kwamagalelo ngamanye okanye amagalelo kumandla entsimi |
| Imilinganiselo (H x W x D), malunga. | 56.0 x 12.0 x 75.5 mm (2.21 x 0.47 x 2.97 kwi.) |
| Indawo yokutshintshela iqhosha | 3 |
| Ukalisho lohlobo lwesivalo | Akukho (isimbo esivulekileyo) |
| Ubungakanani bocingo | 0.25...2.5 mm2 (22…14 AWG) ucingo lobhedu oluqinileyo okanye olubotshwe kumlinganiselo we-100 °C (212 °F), okanye ngaphezulu,1.2 mm (3/64 in.) |
| Udidi lweeNcingo (1) | I-2 - kwiimpawu ze-1 - kwii-ports zamandla |
| Uhlobo locingo | Ikhuselwe |
| Isiseko se-screw torque yetheminali | Imiselwe yibhloko ye-terminal efakiweyo |
| Ubunzima, malunga. | 35 g (1.235 oz) |
| Ikhowudi yeTempile yaseMntla Melika | T4A |
| UKEX/ATEX ikhowudi yeTemp | T4 |
| IECEx ikhowudi yeTemp | T4 |
(1) Sebenzisa olu lwazi lwecandelo le-conductor ukucwangcisa umzila womqhubi njengoko kuchaziwe kwi-Industrial Automation Wiring kunye ne-Grounding Guidelines, upapasho 1770-4.1.
Iinkcukacha zokusingqongileyo
| Uphawu lophawu | Ixabiso |
| Ubushushu, ukusebenza | IEC 60068-2-1 (I-Ad yoVavanyo, i-Operating Cold), i-IEC 60068-2-2 (I-Bd yoVavanyo, i-Operating Dry Heat), i-IEC 60068-2-14 (Uvavanyo lwe-Nb, i-Operating Thermal Shock): -20 °C ≤ Ta ≤ +55 °C (-4 °F ≤ Ta ≤ + 131 °F) |
| Iqondo lobushushu, umoya oyingqongileyo, max | 55 °C (131 °F) |
| Ubushushu, ukungasebenzi | IEC 60068-2-1 (uVavanyo lwe-Ab, uVavanyo lwe-Ab olungapakishwanga oluNgapakishwanga oluNgapakishwanga lubandayo),IEC 60068-2-2 (uVavanyo lwe-Bb, uVavanyo lwe-Bb olungapakishwanga oluNgapakishwanga oluNgapakishwayo oluNgapakishwayo oluNgapakishwayo oluNgapakishwayo noBushushu oBomileyo),IEC 60068-2-14 (uVavanyo lweNa, olungapakishwanga olungapakishwanga lwe-Nonoperating Thermal Shock):-40 +85 °C (-40…+185 °F) |
| Ubuntu bezizalwane | IEC 60068-2-30 (Uvavanyo lwe-Db, olungapakishwanga Damp Ubushushu): 5…95% ukunganyusi |
| Ukungcangcazela | IEC 60068-2-6, (Vavanya i-Fc, i-Operating): 5 g @ 10…500 Hz |
| Ukothuka, ukusebenza | IEC 60068-2-27 (Vavanya i-Ea, Umothuko ongapakishwanga): 30 g |
| Umothuko, awusebenzi | IEC 60068-2-27 (Vavanya i-Ea, Umothuko ongapakishwanga): 50 g |
| Izinto ezikhutshwayo | I-CISPR 11IQela loku-1, iKlasi A |
| Ukungakhuseleki kwe-ESD | IEC 61000-4-2: 6 kV ukukhutshwa koqhagamshelwano 8 kV ukukhutshwa komoya |
| I-radiated RF immunity | IEC 61000-4-3:10V/m ene-1 kHz sine-wave 80% AM ukusuka kwi80…6000 MHz |
| EFT/B ukunganyangeki | IEC 61000-4-4:±3 kV kwi-5 kHz kumazibuko ombane±3 kV kwi-5 kHz kumazibuko omqondiso |
| I-immunity engapheliyo | IEC 61000-4-5:±1 kV line-line (DM) kunye ±2 kV line-earth(CM) kumazibuko ombane±2 kV line-earth(CM) kumazibuko akhuselweyo |
| Kuqhutywe i-RF immunity | IEC 61000-4-6:10V iirms ezine-1 kHz sine-wave 80% AM @ 150 kHz…80 MHz |
Iziqinisekiso
| Isiqinisekiso (xa imveliso imakishwa)(1) | Ixabiso |
| c-UL-us | Izixhobo zoLawulo lwezoShishino lwe-UL, eziqinisekisiweyo zase-US naseKhanada. Jonga uUL File E65584.UL Uluhlu lweKlasi yoku-I, iCandelo le-2 Iqela A, B, C, D Iindawo ezinobungozi, eziqinisekisiweyo ze-US kunye neKhanada. Jonga uUL File E194810. |
| I-UK kunye ne-CE | I-UK Statutory Instrument 2016 No. 1091 kunye ne-European Union 2014/30/EU EMC Directive, ehambelana ne: EN 61326-1; IMeas./Control/Lab., Imfuno yoShishino Sen 61000-6-2; I-Industrial Immunity EN 61000-6-4; I-Industrial Emission Sen 61131-2; Abalawuli abaCwangcisiweyo (iGatya le-8, i-Zone A kunye ne-B) i-UK Statutory Instrument 2012 No. 3032 kunye ne-European Union 2011/65/EU RoHS, ehambelana ne: EN IEC 63000; Amaxwebhu obugcisa |
| Ex | I-UK Statutory Instrument 2016 No. 1107 kunye ne-European Union 2014/34/EU ATEX Directive, ehambelana ne: EN IEC 60079-0; iMfuneko ngokuBanzi Sen IEC 60079-7; I-Atmospheres eqhumayo, uKhuseleko “e” II 3 G Ex ec IIC T4 Gc DEMKO 04 ATEX 0330347X UL22UKEX2478X |
| IECEx | Inkqubo ye-IECEx, ehambelana ne-withies 60079-0; Iimfuno ngokubanzi IEC 60079-7; I-Atmospheres eqhumayo, uKhuseleko “e” II 3 G Ex ec IIC T4 IECEx UL 20.0072X |
| I-EAC | I-Russian Customs Union TR CU 020/2011 EMC Technical Regulation |
| RCM ulwandiso | UMthetho we-Australian Radio Communications Act, ohambelana ne: AS/NZS CISPR 11; Ukukhutshwa kwamashishini |
Iziqinisekiso (Iyaqhutywa)
| Isiqinisekiso (xa imveliso imakishwa)(1) | Ixabiso |
| KC | UBhaliso lwaseKorea lweZixhobo zoSasazo kunye noNxibelelwano, oluthobela: Inqaku lama-58-2 loMthetho wamaza eRadio, iGatya lesi-3 |
| Morokho | Arête yomphathiswa n ° 6404-15 du 29 Ramadan 1436 |
| CCC | I-CNCA-C23-01 yeCCC yokuPhunyezwa koMthetho wokuPhumeza-ubungqina beeMveliso zoMbane zeCCC: 2020122309111607 |
(1) Jonga ikhonkco leSatifikethi seMveliso kwi rok.auto/certifications ukwenzela isiBhengezo sokuThotyelwa, iziQinisekiso, kunye nezinye iinkcukacha zezatifiketi.
Inkxaso yeRockwell Automation
Sebenzisa ezi zixhobo ukufikelela kulwazi lwenkxaso.
| Iziko leNkxaso yobuGcisa | Fumana uncedo malunga neevidiyo, ii-FAQ, incoko, iiforam zabasebenzisi, isiseko solwazi, kunye nohlaziyo lwesaziso semveliso. | rok.auto/support |
| Iinombolo zeFowuni zeNkxaso yobuGcisa beNgingqi | Khangela inombolo yefowuni yelizwe lakho. | rok.auto/phonesupport |
| Iziko loBugcisa lobuGcisa | Ukufikelela ngokukhawuleza kwaye ukhuphele iinkcukacha zobugcisa, imiyalelo yokufakela, kunye neencwadana zabasebenzisi. | rok.auto/techdocs |
| Ithala leencwadi | Fumana imiyalelo yokufakela, iimanyuwali, iincwadana, kunye noshicilelo lwedatha yobugcisa. | rok.auto/literature |
| Ukuhambelana kweMveliso kunye neZiko lokuKhuphela (PCDC) | Khuphela i-firmware, ehambelana nayo files (ezifana ne-AOP, EDS, kunye ne-DTM), kunye nokufikelela kumanqaku okukhutshwa kwemveliso. | rok.auto/pcdc |
Ingxelo yoxwebhu
Izimvo zakho zisinceda ukuba sifeze iimfuno zamaxwebhu akho ngcono. Ukuba unazo naziphi na iingcebiso malunga nendlela yokuphucula umxholo wethu, gcwalisa ifom apha rok.auto/docfeedback.
Inkunkuma yoMbane kunye neZixhobo zoMbane (WEEE)
Ekupheleni kobomi, esi sixhobo kufuneka siqokelelwe ngokwahlukileyo kuyo nayiphi na inkunkuma kamasipala engalungiswanga.
I-Rockwell Automation igcina ulwazi lwangoku lokuthotyelwa kwemveliso yendalo kuyo webindawo kwi rok.auto/pec.
Rockwell Tricare A.Ş. Kar Plaza Markaz E Blok Kat:6 34752 , İstanbul, Umnxeba: +90 (216) 5698400 EE
Qhagamshelana nathi.
ukwandisa amathuba omntu®
AMERIKA: Rockwell Automation, 1201 South Second Street, Milwaukee, WI 53204-2496 USA, Tel: (1) 414.382.2000, Fax: (1) 414.382.4444 EUROPE/MIDDLE EAST/AFRICA: Rockwell Automation Park, Dev. Keelan 12a, 1831 Diego, Belgium, Tel: (32) 2 663 0600, Fax: (32)2 663 0640 ASIA PACIFIC: Rockwell Automation, Level 14, Core F, Cyber port 3, 100 Cyber port Road, Hong Kong. Umnxeba: (852) 2887 4788, Fax: (852) 2508 1846 UNITED KINGDOM: Rockwell Automation Ltd. Pittsfield, Kiln Farm Milton Keynes, MK11 3DR, United Kingdom, Umnxeba:(44)(1908) 838-800,Fax: 44)(1908) 261-917
U-Allen-Bradley, ukwandisa amathuba omntu, iFactory Talk, POINT I/O, POINT Bus, Rockwell Automation, Studio 5000 Logix Designer, kunye neTech Connect ziimpawu zorhwebo zeRockwell Automation, Inc. ControlNet, Device Net, kunye neEther Net/IP ziimpawu zorhwebo. ye ODVA, Inc.
Iimpawu zentengiso ezingezizo ezeRockwell Automation ziyipropathi yeenkampani zabo.
Ushicilelo 1734-IN032F-EN-P - Septemba 2022 | Supersedes Publication 1734-IN032E-EN-P – March 2021 Copyright © 2022 Rockwell Automation, Inc. Onke amalungelo agciniwe.
Amaxwebhu / Izibonelelo
 |
Allen-Bradley POINT I/O 4 Isitishi esiPhezulu soXinano lweeModyuli zokuNgenisa zangoku [pdf] Incwadi Yomyalelo I-1734-IE4C, 1734-IE4CK, i-Series C, i-POINT IO ye-4 ye-Channel High Density ye-Input Modules yangoku, i-POINT IO 4, i-Channel High Density ye-Input Modules yangoku, iiModyuli zokuNgena eziNxinano zangoku, iiModyuli zoNgeniso zangoku, iiModyuli ze-Input zangoku, iimodyuli ze-Input zangoku. Iimodyuli |
