WSD LED BRI810-C-F Bi-Level and Daylight Harvest Microwave Sensor
Product Information
Product Model: BRI810-C-F
FCC Compliance: This device complies with part 15 of the FCC Rules. It meets the requirements for operation without causing harmful interference and must accept any interference received.
FCC Warning: Any changes or modifications not approved by the responsible party could void the user’s authority to operate the equipment.
Radiation Exposure Limits: The equipment complies with FCC radiation exposure limits for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and the user’s body.
Product Usage Instructions
- Reorient or relocate the receiving antenna if experiencing interference.
- Increase the separation between the equipment and receiver if interference persists.
- Connect the equipment into an outlet on a different circuit than the receiver if interference continues.
- If assistance is needed, consult the dealer or an experienced radio/TV technician.
DIMENSION
SPECIFICATIONS
| Power supply | 120/277VAC 50/60Hz |
| Maximum load
@ -40°F – +158°F (-40°C – +70°C) |
Resistive/Tungsten – 600W@120V
Electronic Ballast (LED)- 800VA@120V/1200VA@277V |
| HF System | 5.8GHz CW |
| Dim control output | 0-1OV, max. 25mA sinking current |
| Detection radius/angle | Max 26ft.(8m) /360° |
| Mounting height | Max 40ft |
| Humidity | Max. 95% RH |
| Temperature | -40°F- +158°F (-40°C- +70°C) |
NOTE: The high-frequency output of this sensor is <0. 2mW-that is just one 5000™ of the transmission power of a mobile phone or the output of a microwave oven.
SENSOR COVERAGE
WARNING
- NOTE: Warm up time is 15seconds. After the sensor connects input power, the light will keep on 15seconds, then go to dimming to work normally.
- NOTE: Factory Default Setting: 100% sensitivity, Hold on time: 10seconds, Daylight sensor is 30lux, Dimming level: 30%, Dimming time: 60minitues.
- NOTE: Any setting changed by DIP Switch, the light that sensor connect will on/off as confirm.
UTILIZING FIELD AND INTRODUCTION
BRI810-C-D is a moving object sensor that can detect range of 360° and it’s working frequency is 5. 8GHz. The advantage of this product is stable working state (stable working temperature:
-40°C~+70°C), BRI810-C-D adopts a microwave sensor(high-frequency output<0.2mW), so that it issafe and performs better than infrared sensor.
FUNCTION AND OPTIONS
Daylight Harvesting Function
A control method based on the control of artificial light with available natural light. The purpose is to control the output of artificial light according to the change of natural light, while ensuring that the illumination of the target space does not change to maintain a certain illumination.
ON-OFF Function
Switch on the lamp on detection of movement, and switch off after a hold time when there is no motion detected. As built-in daylight sensor can read brightness value, the sensor does notswitch on the lamp if with sufficient natural light. 
WIRING DIAGRAMS
PARAMETER SETTING BY DIP SWITCH
Detection rang can be reduced by selecting the combination on the DIP switches to fit precisely each application:
Hold Time Setting
File of switch location and stand-by time setting as follow:
The chosen lamp response threshold can be infinitely from approx. 10-50lux, switch location and light-control of the corresponding table is as follows:
The corresponding file of switch location and stand-by level as follows:
FCC STATEMENT
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try tocorrect the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &your body.
Documents / Resources
 |
WSD LED BRI810-C-F Bi-Level and Daylight Harvest Microwave Sensor [pdf] User Manual 2BBPO-BRI810, 2BBPOBRI810, bri810, BRI810-C-F, Bi-Level and Daylight Harvest Microwave Sensor, BRI810-C-F Bi-Level and Daylight Harvest Microwave Sensor, Daylight Harvest Microwave Sensor, Harvest Microwave Sensor, Microwave Sensor, Sensor |