Winkhaus-logo

Winkhaus TTP/Handle Operated plus Split Follower

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-product-image

Specifications

  • Product: Door Locking System
  • Lock Actuation: TTP/Handle-operated + split follower
  • Product Groups: hookLock, solidLock, easyLock
  • Manufacturer: Winkhaus
  • Website: winkhaus.com

General Information

Lock actuation

  • Describes locking and unlocking of the security door lock.
  • TTP/Handle-operated + split follower

Product group
The Winkhaus product range includes a wide range of multi-point locking systems for fast and powerful locking of external doors.

The specified lock actuation can be found in the following product group:

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (1)

About these instructions
These instructions ensure safe handling of the product. Observing the information in these instructions can help to prevent accidents and material damage.

You can download these instructions in other languages as a PDF file via the following QR code:

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (2)

Operating instructions for end users
https://www.winkhaus.com/bedienungshinweise-fuer-endanwender-stv

Safety instructions

Advice on specialised staff
Installing or repairing a locking system requires specialist knowledge, which is why this work should only be carried out by specialists or instructed persons.

General instructions for use
The following instructions and markings, as well as the associated warnings, apply to the safe operation of doors.

Risk of severe injuries through trapping of body parts in the opening gap between sash and frame.

  • When closing doors, never reach between sash and frame, and always proceed with care.
  • Keep children and people who cannot estimate the dangers away from the point of danger.

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (3)

Risk of minor injuries and material damage due to additional load on the door sash.
Do not place any additional load on the door sash. Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (4)

Risk of minor injuries and material damage from inserting obstructions into the opening gap between sash and frame.
Do not insert obstructions into the opening gap between sash and frame. Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (5) Risk of minor injuries and material damage due to uncontrolled closing and opening of the door sash.

  • Make sure that the door sash is guided slowly by hand over the entire movement range to the complete closing or opening position.
  • Prevent wind from acting on the open door sash.
  • Close doors in case of wind and draft.Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (6)

Risk of minor injuries and material damage due to the door sash pressing against the opening edge or the wall reveal.
Do not press the door sash against the opening edge or the wall reveal.

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (7)Operation

Lock actuation

TTP/Handle-operated + split follower

Closing
Pull the handle up (max. 45°), the locking elements are disengaged. As soon as the door sash has been pulled closed, the door can no longer be opened from the outside via the handle; the latch can only be retracted via the profile cylinder.

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (8)

Locking
After the door has been correctly closed, a single turn of the key (approx. 1 x 360°) locks the door. The clicking of the handle latch while turning the key can be felt due to a slight resistance that must be overcome. The handle can no longer be pushed downwards. The locking elements are securely fixed. It is no longer possible to push back the locking elements from outside.

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (9)

Release
Rotate the key once (approx. 1 x 360°), pull back. The release of the handle or key blockage is perceptible. The handle can now be pushed downwards. The locking elements are no longer blocked and can be retracted using the handle; the latch can only be retracted from the outside via the profile cylinder.

Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (10)

Opening
Push the door handle downwards (max. 45°); the locking components are retracted. The latch is retracted from the outside via the profile cylinder and from the inside via the handle.Winkhaus-TTP-Handle-Operated-plus-Split-Follower-image (11)

Manufactured and distributed by:

  • Aug. Winkhaus SE & Co. KG
  • August-Winkhaus-Straße 31
  • 48291 Telgte
  • Germany

Contact:

For UK imported by:

  • Winkhaus UK Ltd.
  • 2950 Kettering Parkway
  • NN15 6XZ Kettering
  • Great Britain

Contact:

STV PH December 2024 · SAP-No. 5121642 · v1.0 · EN · All rights and modifications are reserved.

FAQ

  • Q: Where can I find additional languages for the operating instructions?
    • A: You can download the instructions in other languages as a PDF file via the QR code provided in the manual or visit the manufacturer’s website for more information.
  • Q: What should I do if I encounter difficulties in locking or unlocking the door?
    • A: If you experience any issues with the lock actuation, contact a specialist or the manufacturer for assistance to avoid any potential damage to the locking system.

Documents / Resources

Winkhaus TTP/Handle Operated plus Split Follower [pdf] Instruction Manual
2024-12-11, TTP Handle Operated plus Split Follower, Handle Operated plus Split Follower, Operated plus Split Follower, Split Follower, Follower

References

Leave a comment

Your email address will not be published. Required fields are marked *