WEINTEK M02 WiFi Expansion Module
Chapter 1 Overview
Specification
Feature
- Modular design, adds wireless connectivity to HMI.
- WiFi standards supported include: IEEE 802.11b/g/n.
- Compact design and little protrusion when installed on HMI, which avoid space issue in control cabinet installation.
- The magnetic mount antenna included in the package can be installed at an optimal location to maximize signal strength.
| Network | WiFi | IEEE 802.11 b/g/n 802.11b: max 19.76 dBm 802.11g: max 19.93 dBm 802.11n: max 19.99 dBm |
| I/O Port | SMA Female Connector | 1 |
| Male Connector to HMI | 1 | |
| Power | Input Power | 5VDC |
| Power Consumption | 900mA@5VDC (powered by HMI) | |
| Voltage Resistance | 500VAC (1min.) | |
| Isolation Resistance | Exceed 50MW at 500VDC | |
| Specification | PCB Coating | N/A |
| Enclosure | Plastic | |
| Dimensions WxHxD | 54.5 x 80 x 24.1 mm | |
| Weight | Approx. 80 g | |
| Mount | HMI connector + diagonal screw fastening | |
| Environment | Protection Structure | M02: IP20 Compliant Antenna: IP66 Compliant |
| Storage Temperature | -20° ~ 60°C (-4° ~ 140°F) | |
| Operating Temperature | 0° ~ 55°C (32° ~ 131°F) | |
| Relative Humidity | 10% ~ 90% (non-condensing) | |
| Altitude (Air Pressure) | Below 3,000 meters (70.1kPa) | |
| Vibration Endurance | 10 to 25Hz (X, Y, Z direction 2G 30 minutes) | |
| Certificate | CE | CE marked |
| UL | cULus Listed | |
| Software | EasyBuilder Pro | V6.05.02 or later versions |
Dimensions
| a | SMA Female Connector |
| b | Male Connector to HMI |
Installation
M02 does not support hot swapping by design. Please connect it to HMI before powering up HMI. 
Chapter 2 WiFi Settings
Connect M02 to HMI and then start up HMI. Log in system settings in one of the following two ways and configure WiFi parameters.
Set in internet browser
Connect HMI with PC using an Ethernet cable, open internet browser (IE, Chrome, or Firefox), and enter HMI’s IP address (e.g.: 192.168.2.177) to configure HMI settings.
Network » WiFi: Select WiFi AP and define the encryption type. 
Network » Hotspot: Make the HMI a wireless hotspot to share internet connection if needed. 
Set on HMI
Tap the button on HMI to access the relevant settings for the HMI. At the bottom of the Network page, WiFi Connection settings can be found. 
WiFi: Select WiFi AP and define the encryption type.
WiFi Hotspot: Make the HMI a wireless hotspot to share internet connection if needed. 
WiFi TX Power: After successfully logging in with the correct password, the default power or enhanced power can be configured here.
Note
- The IP address for WiFi and the IP address for LAN1/LAN2 can belong to the same domain or different domains.
- A WiFi hotspot’s connection can be shared with up to 10 client devices at a time.
Other company names, product names, or trademarks in this document are the trademarks or registered trademarks of their respective companies.
This document is subject to change without prior notice.
Documents / Resources
 |
WEINTEK M02 WiFi Expansion Module [pdf] User Manual M02, M02 WiFi Expansion Module, M02, WiFi Expansion Module, Expansion Module, Module |