WALKER H27i Tractor

Specifications
- Model: H27i
- Beginning S/N: 190455
- Part Number: 2000-50
Product Information
The illustrated parts manual provides a detailed list of components and assemblies for the tractor model H27i. It includes information on decals, body/chassis assemblies, tractor components, electrical components, maintenance procedures, and warranty details.
TRACTOR DECALS

FRONT & REAR BODY ASSEMBLIES

| 1 | 6103-14 | Suspension Seat | 1 | F004 | 1/4-20 Keps Nut | 13 | |
| 2 | 2105-12 | Rear Body (Includes Item # 3) | 1 | F005 | 1/4-20 ESNA Nut | 2 | |
| 3 | 2190-1 | Insulation Foam Pad | 1 | F009 | 5/16-18 Whiz Locknut | 12 | |
| 4 | 7844 | Rubber Bumper (1.25 x .250) | 2 | F020 | 5/16-18 ESNA Nut | 1 | |
| 5 | 5146 | 10mm Ball Stud | 2 | F023 | 10-24 ESNA Nut | 5 | |
| 6 | 2145 | Gas Spring | 1 | F029 | 1/4-20 x 1/2 Hex Bolt | 4 | |
| 7 | 5180 | Edge Molding, Lever Opening | 2 | F034 | 5/16-18 x 3/4 Hex Bolt | 4 | |
| 8 | 2504-4 | Hinge (22.5) | 1 | F049 | 5/16 SAE Washer | 4 | |
| 9 | 2100-8 | Front Body | 1* | F060 | AN960516 Washer | 2 | |
| 10 | 5989-55 | Dome Plug (1/2) | 1 | F091 | 5/16-18 x 5/8 Hex Bolt | 4 | |
| 11 | 7854 | Plastic Tip, Red | 1 | F093 | 5/16-18 x 1 Hex Bolt | 1 | |
| 12 | 2383 | Body Latch Hook | 1 | F236 | 1/4-20 x 1-3/4 Hex Bolt | 2 | |
| 13 | 7222 | Extension Spring (1/4 x 3) | 1 | F246 | 1/4-20 x 1/2 PTHMS | 4 | |
| 14 | 6103-44 | Grammer Seat Mount Channel, RH | 1 | F341 | Coil Roll Pin (7/64 x 9/16) | 1 | |
| 15 | 6103-45 | Grammer Seat Mount Channel, LH | 1 | F342 | 5/16 Conical Washer | 2 | |
| 16 | 5989-4 | Dome Plug (3/8) | 2 | F442 | 1/4-20 x 5/8 PTHMS | 5 | |
| 17 | 5989-3 | Dome Plug (5/16) | 2 | F613 | 10-24 x 1/2 Truss Head Torx | 5 | |
| 18 | 4102-1 | Body Guide, Upper | 1 | ||||
| * Decal H27i is available by ordering P/N 8821-5.
Tilt-Up Latch Assembly** |
|||||||
| ** | Complete Tilt-Up Latch Assembly Kit available by ordering | ||||||
| 19 | 5847 | Plastic Tip | 1 | kit # 5744-5. | |||
| 20 | 5744-20 | Spring Arm, Tilt-Up Latch | 1 | ||||
| 21 | 5744-10 | Spring Pivot Bushing | 1 | ||||
| 22 | 5744-15 | Compression Spring (3/8 x 5/8) | 1 | ||||
| 23 | 5744-13 | Mount Angle, LH | 1 | ||||
| 24 | 5744-12 | Hook, Tilt-Up Latch | 1 | ||||
| 25 | 5744-14 | Mount Angle, RH | 1 | ||||
Chassis Assembly
- 1 2325-8 Belt Guide 1
- 2 2046-1 Gas Tank Mount, LH 1
- 3 2301 Debris Shield 1
- (Includes Items # F004 & F029)
- 4 2301-15 Debris Guard 1
- 5 2301-16 Back Up Plate 1
- 6 2300-13 Chassis Frame 1
- 7 2046 Gas Tank Mount 1
- 8 4102-2 Body Guide, Lower 1
Tail Wheel Assembly
- 9 5830 Grease Fitting 2
- 10 2201-2 Fiberglide Thrust Washer 2
- 11 2201-3 Fiberglide Bearing (1-5/8) 2
- 12 5830-4 Grease Fitting (90 Deg.) 1
- 13 2201-4 Washer (2-1/4 x 7/16 x 1/4 Thk) 1
- 14 8769-8 Dust Cap, Deck Caster 2
- 15 8769-6 Bearing Cone (1″ ID) 4
- 16 8769-5 Bearing Cup (2 x 1-5/8) 4
- 17 2300-10 Tail Wheel Pivot 1 (Includes Items # 9, 11, 12 & 16)
- 18 8769-7 Seal 2
- 19 2770 Caster Wheel Fork 2
- 20 8039 Nut, Tail Wheel Axle 2
- 21 8038-1 Spacer, Wheel Axle 2 (.750 ID x 1.125 OD)
- 22 8768-2 Seal, Reverse Lip 4
- 23 8037 Bearing Cone (3/4 ID) 4
- 24 8035-1 Wheel & Tire (13 x 4.50-6) 2(W/Bearing Race) 8035-3 Tail Wheel Tire (13 x 4.5-6 Ply) *
- 25 7038 Wheel Axle (3/4 x 5-9/16) 2
Deck Support Arm & Hitch Assemblies
- 26 2300-9 Deck Arm Support Mount 1
- 27 6840-1 Support Arm Bushing (2-1/16) 2
- 28 5830-1 5/16-24 4″ Grease Fitting 2
- 29 2775 Lynch Pin (5/16 x 1-1/4) 2
- 30 2431-2 Deck Support Arm, LH (Includes Item # 28) 1
- 31 2430-2 Deck Support Arm, RH (Includes Item # 28) 1
Fasteners
- F004 1/4-20 Keps Nut 6
- F005 1/4-20 ESNA Nut 4
- F009 5/16-18 Whiz Locknut 8
- F029 1/4-20 x 1/2 Hex Bolt 4
- F031 1/4-20 x 5/8 Hex Bolt 2
- F034 5/16-18 x 3/4 Hex Bolt 8
- F211 1/4-20 x 7/8 Hex Bolt 4
- F218 7/16 Split Lock Washer 5
- F219 7/16-14 x 1-1/4 Hex Bolt 5
- F256 7/16 SAE Washer 1
- F344 3/4-16 Slotted Hex Nut 2
- F348 1/8 x 1-1/2 Cotter Pin 2
- F430 7/16-20 ESNA Nut 2
- F446 7/16-20 x 3-1/2 Grd 8 Bolt 2
- F477 1/4-20 x 5/8 Carriage Bolt 2
- F639 Belleville Washer (1.5 x .755 x .072) 2
- F718 5/16-18 x 5/16 Set Screw (Knurl Point) 2
* Service Part Only
CHASSIS ASSEMBLY

PTO Drive Assembly
- 4850 Handle Grip, Black 1
- 2358-1 Clutch Lever, MBS (Includes Items # 1 & 3) 1
- 5830-3 Grease Fitting (45 Deg.) 4
- 4303-7 Clutch Actuator Bolt (5/16) 1
- 2306-2 Oilite Flanged Bushing 2
- 2325-7 Clutch Arm (Includes Items # 3 & 5) 1
- 5221-1 Extension Spring (3/4 x 5) 1
- 2358-11 Clutch Actuator 1
- 5214-13 Ball Joint (3/8) 2
- 2011-12 Flex Coupling Guard 1
- 2358-9 Clutch Pivot Base 1
- 2358-8 Adjustor Brace 1
- 2302-16 Right Hand Shoe 1
- 2302-3 Left Hand Shoe 1
- 7775-6 Wire Lock Pin (2-1/2″) 1
- 2349-17 Bearing Mount 1
- 2406-5 Spacer 1
- 2236-5 PTO Pulley (4.5/AAA) 1
- 2359-1 Brake Band / Guard Mount 1
- 7775-8 Wire Lock Pin (4″) 1
- 2302-5 PTO Shoe 1
- 5830 Grease Fitting 1
- 7275-16 Universal Joint Tube Assembly / Spline 1
- 2274-10 PTO Drive Shaft Assembly *
- 2302-6 Shoe Mount, LH 1
- 2302-17 Upper Shoe, LH 1
- 2358-7 Clutch / Pivot Stop 1
- 4359-2 Brake Band Link, Rear 1
- 8304 Brake Band (14-1/2) 1
- 4359-1 Brake Band Link, Front 1
- 7523-2 Clevis Pin W/Hole (1/4 x 5/8) 1
- 2410-2 Drive Shaft 1
- 2265 Bearing (20mm) 4
- 2406-7 Pivot Shaft Spacer 1
- 2236-1 Idler Pulley (4.5/AAA) 2
- 2230 Engine PTO Belt / Set (3) 1
- 2236-6 Pulley (Includes Items # F149 & F718) 1
- 2236-4 Idler Pulley Shaft 1
- 7201-3 Fiberglide Bearing 2
- 7201-9 Inner Race (5.324) 1
- 2359-3 Clutch Idler Arm 1 (Includes Items # 3 & 39)
- 2349-6 Flanged Bearing 1
- 2358-12 Fiberglide Bushing 1
- 7201-2 Fiberglide Bearing 1/2″ 1
- 7377 Plastic Washer (1 x .438 x .025) 2
- 7378 Pivot Bearing (7/16 x 9/16) 1
- 5214-2 Ball Joint (5/16-24) (Nylon Lined) 1
- 7226 Compression Spring (3/4 x 2-1/2) 1
- 7380 Knuckle Joint 1
Fasteners
- F004 1/4-20 Keps Nut 4
- F008 5/16-24 Keps Nut 1
- F009 5/16-18 Whiz Locknut 13
- F010 5/16-24 ESNA Nut 1
- F012 3/8-16 Keps Nut 1
- F013 3/8-16 Whiz Locknut 2
- F014 3/8-16 ESNA Nut 1
- F019 1/4-20 ESNA Wing Nut 1
- F020 5/16-18 ESNA Nut 2
- F029 1/4-20 x 1/2 Hex Bolt 1
- F031 1/4-20 x 5/8 Hex Bolt 5
- F034 5/16-18 x 3/4 Hex Bolt 9
- F035 5/16-18 x 1-1/4 Hex Bolt 2
- F039 3/8-16 x 1-1/4 Hex Bolt 1
- F051 3/8 SAE Washer 2
- F060 AN960516 Washer 2
- F061 1/4 Star Lock Washer 1
- F069 3/32 x 1/2 Cotter Pin 1
- F091 5/16-18 x 5/8 Hex Bolt 1
- F104 1/4-20 x 3/4 PFH Bolt 1
- F120 AN960416 Washer 4
- F146 1/4-20 Jam Nut 1
- F149 1/4 x 1/4 x 1-1/2 Key 1
- F168 5/16 Split Lock Washer 1
- F170 5/16 x 1 x 7/64 Flat Washer (Zinc Plate) 1
- F178 1/4 x 1 Fender Washer 1
- F182 1/4 x 5/8 x 1/8 Washer 1
- F183 .312 x .700 x .074 Washer 4
- F211 1/4-20 x 7/8 Hex Bolt 1
- F217 7/16-14 Hex Nut 2
- F218 7/16 Split Lock Washer 2
- F219 7/16-14 x 1-1/4 Hex Bolt 2
- F255 5/16-18 x 1-1/2 Hex Bolt 4
- F298 3/8-24 Jam Nut 2
- F350 1/4-20 LP Nylock 5
- F389 3/8-16 x 2-3/4 Hex Bolt 1
- F431 1/4-20 x 3-1/2 Hex Bolt 1
- F435 1/4 x 1/4 x 1-1/4 Key 2
- F450 Washer 5/8 x 1-3/4 x 1/4 1
- F452 5/8-18 Nylon Locknut 1
- F473 5/16-18 x 5 Hex Bolt 1
- F476 3/8-16 x 6-1/2 Hex Bolt 1
- F477 1/4-20 x 5/8 Carriage Bolt 1
- F484 Washer .380 ID x 1.0 OD x .120 2
- F551 5/16-18 Flange Top Lock Nut 4
- F576 3/8-16 ESNA Wing Nut 1
- F581 1/4-20 x 1-1/4″ Carriage Bolt 1
- F642 1/4 x .042 Belleville Washer 2
- F651 5/16-18 x 5/8 Carriage Bolt Grd 2 4
- F718 5/16-18 x 5/16 Set Screw (Knurl Point) 1
MAIN COMPONENT POWER TRANSMISSION

ENGINE GROUP
Fuel Tank Assembly
- 5082-4 2-1/4 Ratchet Fuel Cap (EPA) 2
- 8055-2 Fuel Tank Gauge 2
- 8043-8 Roll Over Valve 2
- 5977-7 Roll Over Grommet (.900 x 1-1/2) 2
- 5083-1 Bushing, Rubber 2
- 5083-8 Tank Tube (13″) 2
- 5879-3 Hose Clamp (1/2) 7
- M246 Fuel Line (1/4 x 42-1/4″) 2**
- M113 Fuel Line (3/16 x 9-3/4″) 1**
- M113 Fuel Line (3/16 x 12″) 1**
- 7014-9 Fuel Filter 1
- 8043-6 Connector “Y” 1
- 5975-3 Cable Tie (50# x 7″) 4
- M113 Fuel Line (3/16 x 32-3/4″) 1**
- 4010-1 Drain Valve 3/8-18 NPTF 1
- 2010-3 Fuel Valve 1
- 2010-43 Fuel Selector Valve Mount 1
- M246 Fuel Line (1/4 x 11″) 1**
- 8055-1 Fuel Tank, 4.7 Gallon, Gas (Black) 2 (Includes Items # 2-6, 20 & 21)
- 5086-7 Hose (1/4 x 6) 2
- 5020-2 Fuel Filter, In Tank 2
Remote Oil Cooler Assembly
- 22 NS Oil Cooler Hose 1***
- 23 NS Oil Cooler Hose 1***
- 24 NS Clamp 4***
- 25 NS Oil Cooler 1***
- 26 8016-8 Oil Cooler / Reg Mount 1
Engine Assembly
- 27 2104-1 Body Support 1
- 28 4845 Rubber Bumper (1.0 x .625) 2
- 29 NS Kohler Nut *
- 30 2013-4 Shield Side 2
- 31 2013-3 Muffler Heat Shield 1
- 32 NS Oxygen Sensor (Kohler 25 418 07-S) 1
- 33 NS Muffler (Kohler 24 786 33-S) *
- 34 NS 27 HP Engine, EFI (Pulse Pump) *
- (Kohler, Spec. # ECH 749-3064)
Precleaner Assembly
- 35 6029 Hose Clamp (1-13/16 to 2-3/4) 3
- 36 2012-2 Air Intake Hose 1
- 37 7026-4 Remote Precleaner 1
- 38 2088-10 Air Cleaner Assembly *
- (Includes Items # 38-45)
- 39 5091-19 Air Flow Indicator W/Bracket 1
- 40 M258 Vacuum Hose (9.5″) 1**
- 41 5091-5 1/8 Pipe Thread Female W/Barb 1
- 42 5088-3 Air Cleaner Band 1
- 43 2090-3 Safety Filter Insert 1
- 44 2090-1 Air Cleaner Cartridge 1
- 45 2088-2 Air Cleaner Cap 1
- 46 2090-2 Vacuator Valve 1
Throttle Assembly
- 47 2108-4 Control Cable (68″) 1
- 48 8123-3 Insultherm (3/8 x 10) 1
- 49 5108-1 Control Lever, Throttle / Choke 1
- 50 5108-5 Throttle Control Knob, Red 1
- 51 5108-11 Friction Washer (.062) 1
- 52 7108 Control Assembly 1 (Includes Items # 49, 51, 53-55 & F642)
- 2108-5 Throttle Control and Cable Assembly * (Includes Items # 47, 49-51, 53-56, F002,
- F005, F050, F164 & F642)
- 53 5108-8 Control Bracket 1
- 54 5108-10 Friction Washer (.125) 1
- 55 5108-7 Control Lock Tab 1
- 56 5172 Bearing, Delrin (.250 ID x .375 OD x .250) 1
Fasteners
- F002 10-24 Keps Nut 7
- F004 1/4-20 Keps Nut 4
- F005 1/4-20 ESNA Nut 1
- F009 5/16-18 Whiz Locknut 4
- F025 10-24 x 3/8 PPHMS 6
- F031 1/4-20 x 5/8 Hex Bolt 4
- F034 5/16-18 x 3/4 Hex Bolt 2
- F050 1/4 SAE Washer 1
- F094 8-32 x 1/2 PTHMS 2
- F164 10-24 x 1/4 x 3/8 SHL Bolt 1
- F175 1/2 Split Lock Washer 4
- F184 1/4-20 x 1/2 Hex Bolt, SS 4
- F185 1/4 Internal Star Lock Washer, SS 4
- F439 1/2-13 x 1-3/4 Hex Bolt 4
- F482 8-32 Nylock Nut 2
- F642 1/4 x .042 Belleville Washer 1
* Service Part Only
** Required hose specifications:
M113 – 3/16″ ID fuel/oil/vapor hose (Gates 4219-0093 or equivalent)
M246 – 1/4″ ID low permeation (<15g/m^2/day) fuel hose (Parker 38904 or equivalent)
M258 – 7/64″ ID automotive vacuum hose
*** Use the engine model and spec number from Kohler to order this item.
HYDROSTATIC GROUND DRIVE ASSEMBLIES

Parking Brake Assembly
- 2358-6 5/16-18 x 1-3/4 Stud 2
- 2300-20 Parking Brake Hydro Mount, RH 1
- 5103-2 Pivot Bushing (5/16 ID) 2
- 2406-3 Parking Brake Actuator Tube 1
- 5222 Extension Spring (1/2 x 3-1/4) 1
- 2280 Clevis (3/8) 1
- 2406-4 Clevis Pin (5/16 x 1-1/8) 1
- 8655-4 Clevis Pin (5/16 x 3/4) 1
- 2406-14 Brake Actuator Pull 1
- 4407-4 Bow Tie Cotter Pin 5
- 5830 Grease Fitting 1
- 7406-1 Handle Grip, Red 1
- 2406-15 Parking Brake Lever / Idler Mount 1 (Includes Items # 11 & 12)
- 2406-5 Spacer 1
- 2300-1 Parking Brake Hydro Mount, LH 1
- 5281-5 Clevis Pin (1/4 x 0.80) 2
- 2406-10 Parking Brake Rod 2
- 5665-1 Compression Spring (2-1/2) 2
- 5463 Steering Lever Actuator 2
Transaxle Reservoir Assemblies
- 20 2025-17 Straight Thread Hose Fitting 2
- 21 5879-4 Hose Clamp (7/16) 2
- 22 M111 Fuel Line (1/4 x 6-1/4″) 2*
- 23 8043-9 1/4 x 1/4 x 1/4 Tee 1
- 24 5879-3 Hose Clamp (1/2) 4
- 25 M111 Fuel Line (1/4 x 20-1/4″) 1*
- 26 2024-1 Oil Expansion Reservoir (1 Qt.) 1
- 27 2025-24 Cross Member Bracket 1
- 28 2025-19 Hose Channel 1
- 29 5832 Cable Clamp (1/2) 3
Ground Drive Assemblies
- 30 2028-8 Lockout Arm, RH 1
- 31 2248-1 Ground Drive Belt / Kevlar 1
- 32 4245 Idler Pulley (3/A) 2
- 33 4349-12 Flange Bearing (1″) 1
- 34 2240-2 Drive Pulley (Includes Item # F718) 1
- 35 5841 Retainer Washer (3/8 x 1-1/4) 1
- 36 5830-3 Grease Fitting (45 Deg.) 1
- 37 2349-14 Transmission Belt Tensioner 1
- (Includes Items # 36 & 38)
- 38 7201-3 Fiberglide Bearing 2
- 39 7201-4 Inner Race (1-1/2) 1
- 40 6325-3 Spacer Bushing (9/16) 1
- 41 5146 10mm Ball Stud 2
- 42 2215-6 Pressure Dampener 1
- 43 2028-7 Lockout Arm, LH 1
- 44 2026-6 Hydro-Gear® Oil Filter (52114) 2
- 45 9430-1 Spacer Tube 4
- 46 2349-15 Idler Mount 1
- 47 2025-41 Hydro-Gear ZT-3400, LH 1
- 48 2026-41 Hydro-Gear ZT-3400, RH 1
Wheel Assembly
- 49 2071-4 AT Wheel & Tire (23 x 10.50-12) 2
- PTO Coupler
- 50 2351-50 Flex Coupler Half (1″ Bore) 2 (Includes Items # F435 & F718)
- 51 2351-19 Inner Flex Coupler Half 1
- 52 2351-1 Rubber Iso Coupler 6
Fasteners
- F002 10-24 Keps Nut 3
- F004 1/4-20 Keps Nut 2
- F005 1/4-20 ESNA Nut 2
- F009 5/16-18 Whiz Locknut 17
- F010 5/16-24 ESNA Nut 2
- F012 3/8-16 Keps Nut 4
- F013 3/8-16 Whiz Locknut 7
- F015 1/2-20 Wheel Lug Nut 8
- F025 10-24 x 3/8 PPHMS 3
- F031 1/4-20 x 5/8 Hex Bolt 2
- F032 1/4-20 x 3/4 Hex Bolt 2
- F034 5/16-18 x 3/4 Hex Bolt 16
- F035 5/16-18 x 1-1/4 Hex Bolt 1
- F038 3/8-16 x 1 Hex Bolt 2
- F040 3/8-16 x 1-1/2 Hex Bolt 1
- F042 3/8-16 x 2-1/4 Hex Bolt 1
- F049 5/16 SAE Washer 1
- F050 1/4 SAE Washer 2
- F051 3/8 SAE Washer 2
- F052 5/16 Ext. Star Lock Washer 12
- F108 3/8-16 x 2 Hex Bolt 1
- F151 3/8-16 x 7/8 Hex Bolt 2
- F182 1/4 x 5/8 x 1/8 Washer 4
- F183 .312 x .700 x .074 Washer 3
- F226 5/16-18 x 7/8 Hex Bolt 2
- F231 1/4 x 3/4 Woodruff Key (#806) 1
- F336 3/8-16 Jam Nut 1
- F350 1/4-20 LP Nylock 2
- F388 3/8-16 x 2-1/2 Hex Bolt 4
- F434 5/16-18 x 3-1/2 Hex Bolt 4
- F435 1/4 x 1/4 x 1-1/4 Key 2
- F481 Washer 5/16 x 1 x .125 12
- F718 5/16-18 x 5/16 Set Screw (Knurl Point) 6
Required hose specifications:
M111 – 1/4″ ID fuel/oil/vapor hose (Gates 4219-0103 or equivalent)
STEERING CONTROL ASSEMBLIES

Steering Lever & FSC Assemblies
- 5850-2 Handle Grip, Foam (5-1/2) 3
- 4170-4 FSC Lever Assembly (Includes Item # 3) *
- 5830 Grease Fitting 1
- 7201-11 Inner Race (1.938) 1
- 5214-4 Ball Joint (5/16-24) W/O Stud 2
- 4213-3 Control Rod (6-1/4) 1
- 5463-4 Steering Lever Actuator 2
- 5665-1 Compression Spring (2-1/2) 2
- 2213 Control Rod (7″) 2
- 2212-3 Seal Retainer 2
- 2212 Transmission Control Arm Stop 2
- 2212-2 Transmission Control Arm, RH 1
- 5214-2 Ball Joint (5/16-24) (Nylon Lined) 2
- 2212-1 Transmission Control Arm, LH 1
- 2451-1 Steering Pivot Shaft With Stop 1
- 5463-6 Washer (5/16 x 3/4 x .250) 2
- 7201-2 Fiberglide Bearing (1/2″) 2
- 5463-5 Steering Arm Pivot Bushing (SS) 2
- 5830-3 Grease Fitting (45 Degree) 1
- 8201-3 Fiberglide Bearing 4
- 2451-7 Speed Control Actuator, LH 1
(Includes Items # 19 & 20) - 5146 10mm Ball Stud 4
- 4199-4 Steering Lever Dampener Assembly 2
- 2451-8 Speed Control Actuator, RH 1
(Includes Items # 20 & 25) - 5830-4 Grease Fitting (90 Deg.) 1
- 4451-4 FSC Friction Actuator 1
- 4219 Extension Spring (3/4 x 6-1/2) 1
- 5453-20 Steering Lever Handle (+1″) 2
Adjustable / SS
(Includes Items # 1, F050, F188 & F390) - 4452-1 Steering Lever Tube W/Tab 2
- 5450 D-Clip 2
- 5222 Extension Spring (1/2 x 3-1/4) 2
- 4452-6 Steering Pivot (1/4-20 x 1-5/8) 2
- 4142-1 FSC Cam 1
- 5141 FSC Friction Washer 1
(1-1/2 x 3/8 x 1/16) - 4142-2 FSC Friction Washer 1
(1-1/2 x 1-1/32 x 1/16) - 9704-3 Pivot Rod Bushing, Plastic 2
- 2451-4 Steering Shaft Spacer 1
Fasteners
- F004 1/4-20 Keps Nut 2
- F005 1/4-20 ESNA Nut 2
- F008 5/16-24 Keps Nut 2
- F009 5/16-18 Whiz Locknut 6
- F010 5/16-24 ESNA Nut 2
- F024 5/16-24 Jam Nut 4
- F035 5/16-18 x 1-1/4 Hex Bolt 1
- F044 5/16-24 x 3/4 Hex Bolt 2
- F050 1/4 SAE Washer 4
- F093 5/16-18 x 1 Hex Bolt 2
- F121 5/16-18 x 3/8 x 1 SHL Bolt 1
- F146 1/4-20 Jam Nut 2
- F167 5/16-18 Hex Nut 1
- F183 .312 x .700 x .074 Washer 6
- F188 1/4-20 Self-Locking Nut 4
- F192 3/8-24 Self-Locking Nut 1
- F211 1/4-20 x 7/8 Hex Bolt 1
- F226 5/16-18 x 7/8 Hex Bolt 2
- F235 5/16-18 x 2-1/2 Hex Bolt 1
- F385 1/4 x 1-1/4 Roll Pin 1
- F390 1/4-20 x 7/8 Carriage Bolt 4
- F391 1/4-20 x 1/2 Set Screw, SS 2
- F407 Belleville Washer 3/8 x 1.187, SS 1
- F551 5/16-18 Flange Top Lock Nut 1
* Service Part Only
STEERING CONTROL ASSEMBLIES

ELECTRICAL ASSEMBLY
- 8960-15 Ignition Switch W/Keys 1 (Includes Items # 2, 3 & F349)
- 7854 Plastic Tip, Red 1
- 8960-3 Key Set W/Umbrella 1
- 7941-3 Boot, Circuit Breaker 1
- 7941-7 Circuit Breaker (20 Amp) 1
- 8990-1 Hourmeter (Global) 1
- 8996-9 Red Indicator Light Assembly 3
- 8536-2 Warning Horn Assembly 1
- 6105-3 Harness Clip 3
- 5977-3 Grommet (9/16) 1
- 2103-8 Adapter Harness 1
- 6941-9 Relay Switch 30/40 Amp 3
- 7948-6 Time Delay Module (.5 Second Delay) 1
- 7948-5 Time Delay Harness 1
- 5941-2 Safety Switch (NO) 1
- 7833-2 Cable Clamp (1 x 1/4) 2
- 2940-16 Wire Extension 1
- 7938 Lead Wire, Battery Charge 1 (Alternator to Starter)
- 2940-2 Battery Cable, 22″ (+) 1
- 8404-8 Plastic Cover, Red 2
- 8941 Circuit Breaker (30 Amp) 1 (Auto Reset/Sealed)
- 2940-3 Battery Cable, 14″ (-) 1
- 5975-1 Cable Tie (18# x 3-3/4″) 2
- 5932 Battery Terminal Insl., Blk (-) 1
- 5910-6 Battery Spacer Pad 1
- 7910-3 Battery (12V/350A CCA) 1
- 5839 Hook Bolt 2
- 5933 Battery Terminal Insl., Red (+) 1
- 5844 Battery Hold-Down Bar 1
- 5833 Cable Clamp (1/4) 1
- 2940-23 Wire Harness 1
- 5942-4 Safety Switch (NO) 1
- 5942-5 Safety Switch (NO) 1
Fasteners
- F002 10-24 Keps Nut 13
- F004 1/4-20 Keps Nut 2
- F009 5/16-18 Whiz Locknut 1
- F019 1/4-20 ESNA Wing Nut 2
- F026 10-24 x 1/2 PPHMS 13
- F031 1/4-20 x 5/8 Hex Bolt 2
- F034 5/16-18 x 3/4 Hex Bolt 1
- F050 1/4 SAE Washer 2
- F182 1/4 x 5/8 x 1/8 Washer 2
- F232 10-32 Keps Nut 2
- F349 Washer .835 ID 1.122 OD, SS 1

LUBRICATION POINTS
- Steering Lever Pivot Grease 2
- Deck Support Arm Pivot Grease 2
- Deck-to-PTO Coupling Grease 1 (Grease Spline Slide Area)
- Universal Joint Tube Assembly Grease* 1
- FSC Lever Pivot Grease 1
- Clutch Actuator Push Rod Grease 1
- Body Latch Pivot Oil 2
- PTO Clutch Lever Pivot Grease 1
- Clutch Arm Pivot Grease 1
- Hydro Idler Arm Pivot Grease 1
- Transaxle Oil Reservoir Oil/20W-50 1
- Throttle Control Cable Ends Oil 2
- Engine Dipstick Oil** 1
- Tail Wheel Caster Fork Pivot Grease 2
- Rear Axle Pivot Grease 1
- Rear Wheel Bearing Grease 2
- Engine Oil Fill Oil** 1
- PTO Belt Tightener Idler Pivot Grease 1
- Brake Band Pivot Pins (Clevis) Oil 2
- Parking Brake Lever Pivot Grease 1
- Parking Brake Clevis Oil 3
- Throttle Control Pivot Oil 1
* Grease every 25 hours.
** Refer to H27i Operator’s Manual for procedure for checking and changing oil in Engine Crankcase.
NOTE: See Model H27i Operator’s Manual (P/N 2000-38) for proper lubrication intervals.

CASTER WHEEL FORK INSTALLATION
- Installing the Caster Fork with a Belleville Washer:
- Install the fork up into the bearing housing through the lower and upper tapered roller bearings. Rotate the fork as the seal is engaging onto the shaft to prevent the seal lip from rolling.
- Place a Belleville washer onto the fork shaft with the cupped side of the washer down against the bearing, and thread the slotted hex nut finger-tight onto the shaft.
- Using a wrench or socket, tighten the slotted hex nut by hand only until the Belleville washer is fully compressed, which is felt as a distinct increase in the amount of force required to turn the nut.
- Back the nut off one to two notches until the cotter pin hole is visible, and install the cotter pin to lock the nut in place.
NOTE: The tension of the compressed Belleville washer provides the correct amount of bearing pre-load and will remain consistent with use. Do not overtighten the nut, which will bind the caster pivot and cause unnecessary turning friction.
WIRING SCHEMATIC

LIMITED WARRANTY FOR
WALKER MODEL H27i RIDER MOWERS
- WHAT THIS WARRANTY COVERS, AND FOR HOW LONG:
Walker Manufacturing company will, at its option, repair or replace, without charge, any part covered by this warranty which is found to be defective in material and/or workmanship within two (2) years* after date of sale to the original retail purchaser unless the product is used for rental purposes, in which case this warranty is limited to ninety (90) days. At Walker’s request, customer will make the defective part available for inspection by Walker and/or return the defective part to Walker, transportation charges prepaid. All parts and components of the Walker Mower are covered by this warranty except the following components which are warranted separately by their respective manufacturers:
Kohler Engine
The available warranties covering these items are furnished with each mower. Walker does not assume any warranty obligation, liability or modification for these items, which are covered exclusively by the stated warranty of the respective manufacturers noted above.
The Fulbat battery comes with a one (1) year warranty from the date of sale to the original retail purchaser. Warranty claims for the battery are administered through Walker Manufacturing.
Extended warranties are offered for the following powertrain components:
y A three (3) year or 3000 hour (whichever comes first) warranty is offered for Hydro -Gear ZT-3400 hydrostatic trans- missions; covers full cost of replacement up to 1000 hours of use, and after 1000 hours warranty coverage is prorated against 3000 hours. - WHAT THIS WARRANTY DOES NOT COVER:
- This warranty does not cover defects caused by depreciation or damage caused by normal wear, accidents, improper maintenance, improper use or abuse of the product, alterations, or failure to follow the instructions contained in the Owner’s Manual for operation and maintenance.
- The customer shall pay any charges for making service calls and/or for transporting the mower to and from the place where the inspection and/or warranty work is performed.
- HOW TO OBTAIN SERVICE UNDER THIS WARRANTY:
Warranty service can be arranged by contacting the dealer where you purchased the mower or by contacting Walker Manufacturing Company, 5925 East Harmony Road, Ft. Collins, CO 80528. Proof of the date of purchase may be required to verify warranty coverage. - WARRANTY LIMITATION:
- THERE IS NO OTHER EXPRESS WARRANTY. ANY WARRANTY THAT MAY BE IMPLIED FROM THIS PURCHASE INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IS HEREBY LIMITED TO THE DURATION OF THIS WARRANTY AND TO THE EXTENT PERMITTED BY LAW ANY AND ALL IMPLIED WARRANTIES ARE EXCLUDED. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
- WALKER WILL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES AND/OR EXPENSES IN CONNECTION WITH THE PURCHASE OR USE OF THE MOWER. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation(s) or exclusion(s) may not apply to you.
- Only the warranty expressed in this limited warranty shall apply and no dealer, distributor, or individual is authorized to amend, modify, or extend this warranty in any way. Accordingly, additional statements such as dealer advertising or presentations, whether oral or written, do not constitute warranties by Walker, and should not be relied upon.
- This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
WALKER MFG. CO. • 5925 E. HARMONY ROAD, FORT COLLINS, CO 80528 • (970) 221-5614
- FORM NO. 120924
- PRINTED IN USA
- www.walker.com
- ©2024 WALKER MFG. CO
FAQ
- What should I do if a decal is damaged or missing?
If a decal is damaged or missing, contact customer support to obtain a replacement decal and follow the application instructions. - How often should I perform maintenance on the tractor?
Regular maintenance is recommended as per the maintenance schedule provided in the manual. Consult the maintenance and service record sheet for guidance.
Documents / Resources
![]() | H27i Tractor |
References
- Walker Mowerswww.walker.com
- User Manualmanual.tools


