VORTEX B0C7PG8H72 One Handed Operation Aid

Product Specifications:

• Product Name: Vortex
• Intended Use: Spacer/valved holding chamber for delivery of aerosol medication with metered dose inhalers
• Manufacturer: PARI Respiratory Equipment, Inc.
• Contact Information: Tel: 1-804-253-7274, Email: product.info@pari.com
• Address: 2412 PARI Way, Midlothian, VA 23112

Product Usage Instructions

Assembling the Parts:

1. Step 1:
2. Step 4:
3. Vigorously shake the inhaler before every use.
4. Connect the inhaler to the connecting ring on the inhalation chamber.
5. Step 5 (only if using a mask): Attach the mask or mouthpiece securely.

Instructions for Cleaning:

Washing by Hand:

1. Clean the parts before first use and then clean and disinfect once a week thereafter.
2. Remove the one-handed operation aid from the chamber.
3. A. Hand Washing:
   • Soak the part for 15 minutes in lukewarm water with liquid detergent. Agitate gently, then rinse in clear water.
   • Rinse the part in clean water and shake out any excess water.
   • Air dry thoroughly on a clean, lint-free cloth or drying rack before storing for future use.
4. B. Dishwasher Cleaning:
   • Place the part in the top shelf of the dishwasher for cleaning.
   • Remove from the dishwasher, shake out excess water, and air dry as instructed above.

Disinfection: After cleaning, disinfect all parts by placing them in boiling water for 5 minutes. Dry as instructed above.

Frequently Asked Questions

Can I use Vortex with any metered dose inhaler?
Yes, Vortex is designed to work with most metered dose inhalers for aerosol medication delivery.

How often should I clean and disinfect Vortex?
You should clean and disinfect Vortex once a week after first use to maintain proper hygiene and functionality.

Product is non-sterile, not made with BPA or latex.
For use only with PARI Vortex® Non Electrostatic Holding Chamber.

READ ALL INSTRUCTIONS BEFORE USE.

Vortex is indicated for use as a spacer/valved holding chamber for use in delivery of aerosol medication with metered dose inhalers.

ASSEMBLING THE PARTS

Step 1:

• Push the one-handed operation aid onto the inhalation chamber from the back.

Step 2:

• Remove the cap on the metered dose inhaler.
• Shake the metered dose inhaler vigorously before every use.

Step 3:

• Insert the metered dose inhaler in the connecting ring on the inhalation chamber.

Step 4:

• Position the one-handed operation aid so that its round end encloses the metered dose inhaler. To do this, you may have to push the one-handed operation aid farther forwards or backwards.

Step 5 (only if using a mask):

Attach the mask (pediatric mask)

• Take the protective cap off the mouthpiece of the VORTEX.
• Attach the mask to the VORTEX mouthpiece.
  OR

Attach the mask (adult mask)

• Take the protective cap off the mouthpiece of the VORTEX.
• Fit the mask connector into the opening of the PARI adult mask soft.
• Attach the mask to the mouthpiece of the VORTEX with the mask connector.

INSTRUCTIONS FOR CLEANING

DISINFECTION: To disinfect after cleaning, place all parts in boiling water for 5 minutes. Dry as instructed above.

PARI Respiratory Equipment, Inc.
Tel: 1-804-253-7274
www.pari.com | product.info@pari.com
2412 PARI Way, Midlothian, VA 23112

© 2024 PARI Respiratory Equipment, Inc.
051D7019 Rev A 01-24

Documents / Resources

VORTEX B0C7PG8H72 One Handed Operation Aid [pdf] Instruction Manual B0C7PG8H72 One Handed Operation Aid, B0C7PG8H72, One Handed Operation Aid, Handed Operation Aid, Operation Aid, Aid

References

• User Manual