VIVOTEK FT9361-R Access Control Reader
Physical Description
| No. | Description | No. | Description |
| 1 | Display | 2 | NFC induction zone |
| 3 | Reboot button | 4 | Anti-Force dismantle trigger |
Installation
Bracket Moumnt
* Themountbracketwillbeavailablelater.
- Secure the back plate to the mount bracket using 4 M3 x 8.0mm screws.
- Route cables through a hole on the wall or through the bracket. Below are the definitions for these cables.
Lines Name Color Description Line1 GND Black GND 12V Red 12V input GND Brown GND 12V White 12V input WG_DO Purple Wiegand/output DO GND Blue GND WG_DI Green Wiegand/output DO DC12V_OUT Orange 12V output Line2 Button_HC32 Black Button for gate open Senses_HC32 Red Senses for gate open Alarm_In_HC32 Brown Alarm input GND White GND RS485_A Purple RS485 A RS485_B Blue RS485 B NC NC No connection NC NC No connection Relay_SW3_B Green Relay3 B Relay_SW3_A Orange Relay3 A Line3 NC NC No connection Relay_SW2_B Black Relay2 B Relay_SW2_A Red Relay2 A NC NC No connection Relay_SW1_B Brown Relay1 B Relay_SW1_A White Relay1 A NC NC No connection Relay_Lock_NO Purple Relay normally open Relay_Lock_COM Blue Relay normally grand Relay_Lock_NC Green Relay normally close GND Orange GND NC NC No connection Line4 RJ45 – RJ45 Ethernet - Mount the sensor device onto the bracket by sliding it from top down.
- Secure the installation by driving a screw from the bottom of the back plate.
Login and Registration
Server Configuration
- Network configuration: When the FT9361-R is started, proceed with network configuration. DHCP or Static IPs are applicable.
- erver：The FT9361-R requires a connection to a VAST FaceManager server. Click onthe Configuration button on the upper right of screen to configure a VAST Face Managerserver IP. (http://xxx.xxx.xxx.xxx:6073/3rd/vivotek/)
- hanging Server IP：If you need to change server IP, you need to logout and click the Settings button on the upper right corner of the screen.
Log in to the account
- ogin：On the first startup, credentials are required for a name and password.
Reboot
Press the Reboot button and the machine will reboot.
Setting
Long press the screen enter the Setting modevia Password that you set in server.
Reset
Long press the screen, select “Reset”, enter the password: Az123567!. Machine will reset to factory mode.
FCC
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Documents / Resources
 |
VIVOTEK FT9361-R Access Control Reader [pdf] Installation Guide FT9361-R, FT9361R, O5P-FT9361-R, O5PFT9361R, FT9361-R Access Control Reader, FT9361-R, Access Control Reader, Control Reader, Access Reader, Reader |
