VEVOR ZH612 Fixed Rectangular Table Instruction Manual

VEVOR ZH612 Fixed Rectangular Table

Overview

The fixed rectangular table model ZH612 is intended for household and similar indoor use. Follow the manual carefully for correct assembly and keep the manual available for future reference.

Specifications

* Specifications, appearance, and design are subject to modification without prior notice.

Quick Setup / Use

1. Check all packaged components and accessories; each is labeled with a letter or number.
2. Assemble only according to the manual’s assembly steps and assembly diagram; unwrap and separate parts in a clean work area.
3. During assembly, wear ANSI-approved safety goggles and heavy-duty work gloves.
4. Assemble in a clean, well-lit area and keep bystanders/curious people away.
5. Install the table on a clean, soft underlay (e.g., carpet or cardboard) to avoid scratching or damaging the surface.
6. Do not move the table randomly during installation; ensure it is fully installed before moving.
7. Before use, check that the product is not abnormal/defective; stop using it if abnormal.

INTRODUCTION

• This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual.
• The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SAFETY INSTRUCTIONS

INTRODUCTION

Thank you for purchasing our products. Committed to providing customers with the best quality products and service has always been our lifelong goal. Before using the product, please read this instruction manual carefully to ensure correct use. Keep the instruction manual in a place where the user can find it at any time.

ASSEMBLY PRECAUTIONS

There are many components and accessories in the package. Each component and accessory is labeled with a letter or a number, check carefully before using any of them.Keep them away from children to prevent accidents.

1. Assemble only according to these instructions. Improper assembly may create hazards.
2. Wear ANSI-approved safety goggles and heavy-duty work gloves during assembly.
3. Keep the assembly area clean and well-lit.
4. Keep bystanders out of the area during assembly.
5. Do not assemble if tired or when under the influence of alcohol, drugs or medication.
6. The product capabilities apply to properly and completely assembled products only.
7. Please install the product on a clean and soft underlay(such as carpet or cardboard)to avoid scratching or damaging the surface of the product.
8. If possible, you can use power tools to make assembly easier.
9. The main components of the product is relatively heavy. Please pay attention to safety during installation.
10. The product is not stable during installation, Please do not move it randomly before it is completely installed.
11. For additional information regarding the parts listed in the following pages, please refer to the Assembly Diagram of this manual. Unwrap and separate all parts in a clean work area.
    • PLEASE BE SURE TO FOLLOW THE INSTALLATION STEPS IN THE MANUAL TO AVOID UNNECSSARY LOSSES CAUSED BY IMPROPER INSTALLATION.

USE PRECAUTIONS

1. The product complies with relevant standards and regulations. Installation of this device must comply with all applicable regulations, and it should only be operated in well-ventilated areas. Please read the user manual before installing and using this equipment.
2. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
3. This product is not a toy. Do not allow children to play with or near this item.
4. This appliance is intended to be used in household and similar applications such as:
5. Bedroom,hotel,homestay,guest room, office,etc..
6. Please use the product according to the intended use, warn of potential injury from misuse.
7. Please properly keep product. Check whether the product is abnormal before use.If it is abnormal,please stop using it.

PARTS LIST

ASSEMBLY STEP

• Products such as specifications, appearance, and design are subject to modification without prior notice.

Installation Video

Troubleshooting

• Product is abnormal/defective: Stop using it immediately and check the condition of the product before continuing.
• Unsafe or unstable during installation: The manual states the product is not stable during installation—do not move it randomly until it is completely installed.
• Concerns about parts during assembly: Refer to the Assembly Diagram in the manual and re-check that each component/accessory label matches the correct parts before continuing.