Technical Support and E-Warranty Certificate
www.vevor.com/support
BUTTON MAKER MACHINE
INSTRUCTION MANUAL
SHY-BUTTONMAKERMACHINE Button Maker Machine
We continue to be committed to provide you tools with competitive price.
“Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and doses not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.
NEED HELP? CONTACT US!
Have product questions? Need technical support? Please feel free to contact us:
Technical Support and E-Warranty Certificate www.vevor.com/support
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
SAFETY REMINDER
- This badge machine is only applied for the intended purpose. Don’t apply in other applications which exceed safety considerations.
- Children cannot operate this product unless accompanied by an adult.
- Pay attention to safety during operation, and avoid crushing fingers.
COMPONENTS
INSTALLATION STEPS
- Install the up mold on the machine, mold side pin align to back and upward push, the magnetism automatically absorbed.
- Make up mold three holes aligning and lift up, down mold align to sliding rail groove and push to middle, loosen and put down the up mold.
- Put the pin on the side of the slide rail.
- Installation finished and able to start manufacture.
- Put “Tin up cover”–”Paper”(pattern levelly placed)-“Transparent plastic film” into “Lower mold(A)” in sequence, then push the lower mold till up and down mold aligned.
- Use one hand hold the machine body first then stable the machine body by handle, another hand press the machine handle till down press to be bottom.
(NOTE: this time down pressed up mold hinge is open status.
NOTE: Up mold hang is open status.
- Put the “Back plate” into “Lower mold(B)”.
- (NOTE: Brooch should be level and not raised. Adjust the level as indicated by the top triangle.) Push the lower mold to bottom from left to right till up and down mold aligned.
- Hand hold the machine body, right hand down press the handle till up and down mold merged to bottom.
NOTE: Now the up mold hinge is close status, pin pass through the hole. 
- Finish.
NOTE: If use metal back plate, then the “Lower mold(B)” need place the plastic washer. (Metal back plate more thinner, only 58mm need add washer, 25mm and 32mm needn’t it.)
MODEL AND PARAMETER
| Product Model | JMB-X3 |
| Manufactured Badge Specification | Φ25/Φ32/Φ58mm |
| Machine Body Color | Black/Blue/Pink |
| Paper Requirements | 127-157g Copper Plate Paper |
| Accessories With Machine | 1. Φ25/ Φ32/Φ58 Metal back plate * 50 Pieces of each size Φ25/ Φ32/Φ58 Plastic back plate * 50 Pieces of each size 2. Φ25/ Φ32/Φ58 Tin Up Cover *100 Pieces of each size 3. Φ25/ Φ32/058 White paper *20 Pieces of each size 4. Φ25/ Φ32/058 Transparent plastic film *100 Pieces of each size 5. Φ25/ Φ32/Φ58 Round Cutter * 1 Piece of each size 6. Allen Key * 2 Pieces 7. Magic Book *1 8. Washer *2 9. Instruction *1 |
FAILURE AND TROUBLESHOOTING
| Failure Appearance | Possible Reasons | Troubleshooting |
| First time downward press iron cover and not absorbed to up mold | 1.Unsuitable operating method 2.Too much lubricating oil in the up mold |
1.First time downward press up mold hinge is in a separate state 2.Use dean cloth or tissue completely wipe it if found too much lubricating oil on the up mold 3.The up and down mold must be on the same vertical line when dosing |
| Second downward press part not wrapped in | 1.Unsuitable operating method 2.Unsuitable paper thickness 3.Up mold screws loosen |
1.The up and down mold must be on the same vertical line when dosing 2.Use the stipulated thickness paper 3.Place the up mold on the machine body, use the complimentary Allen key to fix the screws in the up mold internal hole center. |
| Not tightly press the badge, pressed in but not firm | 1.The downward press is not in place, not press to the bottom 2.Paper is thinner 3.( 25mm ) Configured metal back consumables do not place the washer |
1.Need press to the bottom when downward pressing 2.Change to use a slightly thicker paper 3.Right side mold place 2mm thickness washer when using the metal back consumables |
| Up mold unable to lift up after pressing manufacture, blocked | 1.Up and down mold position deviated 2.The paper is incorrectly cut round or blocked by a foreign object |
Use a sharp tool (such as a straight screwdriver) to align to middle merge position clearance which is between up and down mold, and pry open with the object like a hammer (Attention: Just tap it generally, it will not be too tightened). |
Manufacturer: Shanghai Muxin Wood Industry Co., Ltd.
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia
Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730
SHUNSHUN GmbH
Römeräcker 9 Z2021, 76351
Linkenheim-Hochstetten, Germany
Pooledas Group Ltd
Unit 5 Albert Edward House, The
Pavilions Preston, United Kingdom
Made In China
Technical Support and E-Warranty Certificate
www.vevor.com/support
Documents / Resources
 | SHY-BUTTONMAKERMACHINE Button Maker Machine |
References
- Contact Us – Official VEVOR Supportwww.vevor.com
- Contact Us – Official VEVOR Supportwww.vevor.com
- User Manualmanual.tools