VEVOR RT017 Router Table User Manual

VEVOR RT017 Router Table User Manual

VEVOR RT017 Router Table - front page
www.vevor.com/support

VEVOR RT017 Router Table - product image

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

General Safety Instructions

Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedure at all times.

  • CONNECT your machine ONLY to the matched and specific power source.
  • ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine.
  • DO NOT wear loose clothing or jewelry when operating your machine.
  • A safe environment is important. Keep the area free of dust, dirt and other debris in the immediate vicinity of your machine.
  • DISCONNECT the power source when changing drill bits, hollow chisels, router bits, shaper heads, blades, knives or making other adjustments or repairs.
  • ALWAYS keep all safety guards in place and ensure their proper function.
  • NEVER reach over the table when the tool is in operation. It is dangerous.
  • ALWAYS keep blades, knives and bits sharpened and properly aligned.
  • NEVER leave a tool unattended while it is in operation.
  • BE ALERT! DO NOT use prescription or other drugs that may affect your ability or judgment to safely use your machine.
  • ALWAYS use push sticks and feather boards to safely feed your work through the machine.
  • ALWAYS make sure that any tools used for adjustments are removed before operating the machine.
  • Always keep the bystanders safely away while the machine is in operation.

Router Table with Fence & Stand Specific Safety Instructions

Like all power tools and machinery, proper safety and attention must be adhered to. There is danger associated with using any tool or machine so pay careful attention each and every time you use your tool. If you are not familiar with the operations of a router table, you should obtain the advice and/or instructions from a qualified professional.

  • MAKE SURE the router has been installed securely before staring the machine, for safe operation method.
  • NEVER perform any “Free Hand” operation. Do not use your hands to support or guide the work piece. Always use toggle clamp to secure the work piece for cutting.
  • DO NOT wear jewelry or loose clothing while operating this machine.
  • SAFETY GLASSES & RESPIRATOR is highly recommended when working with this machine. Some sawdust can be harmful to your lungs; please take caution when using this machine.
  • ALWAYS feed the work-piece to the router bit against the rotation direction.
  • INSPECT your work pieces. Make sure that they are free of nails, staples, tacks, knots and other objects that may be harmful to your router bit.
  • DO NOT jam or try and over push the work piece into the machine during operation. This may cause damage to the machine. Feed the work piece with a firm grasp, slowly and easily and hold the work piece against the fence.
  • MAKE SURE the spindle rotates in the correct direction.
  • DO NOT let anyone stand in front of the machine while operation.
  • TECHNICAL DIFFICULTIES. Any problems you may run into should be carefully looked at with the power OFF and the machine unplugged from the power source.
  • NEVER draw the work piece back during the cutting operation. Stop the router bit before drawing back the work-piece.
  • ALWAYS keep bits sharpened and clean.

IMPORTANT: The safety instructions given above can not be complete because the environment in every shop is different. Always consider safety first as it applies to your individual working conditions.

ROUTER TABLE FEATURES

TABLE TOP
Size: 610*400*25mm
Aluminum Miter Track: 610mm
Table Insert: 306*229mm

FENCE
Size: 305*153mm
Dust Port: 63/77.3/68.2mm
Gaurd: Fluorescent Plastic Plate
Aluminum Miter Track: 305mm
Ruler Label: 300mm

STAND
Made of: Steel
Height: 530mm

PHYSICAL FEATURES

VEVOR RT017 Router Table - PHYSICAL FEATURES

ASSEMBLY & INSTALLATION

Before assembling the stand, please take a look at the list below. Your stand comes with the following parts and mounting hardware.

  • Short Angle Brace: 2-pcs
  • Shorter Angle Brace: 2-pcs
  • Long Angle Brace: 2-pcs
  • Longer Angle Brace: 2-pcs
  • Round Head Bolt M8x12: 32-pcs
  • Hex Nut M8: 32-pcs
  • Flat Washer8: 32-pcs
  • Hex Bolt M6x16: 4-pcs
  • Flat Washer: 4-pcs

Stand Assembly

Take the two short and the two longer angle braces out of the box and put it on the floor. Now take the four legs upside down, and attach them to the four braces using 1/4″ x 1/2″ nuts and bolts. (Finger tighten) See Figure-1.
VEVOR RT017 Router Table - Attaching legs to the braces

Now, mount the two other longer and the two short angle braces to the legs with the help of the nuts and bolts, (Finger Tighten). See Figure-2
VEVOR RT017 Router Table - Attaching the middle braces to the legs

Now, turn the stand upright and adjust the legs so that they are evenly positioned, tighten all the screws well.

Installing the Router Table on the Stand

Take the router table and put it upside down on the floor or bench. The router table and the upper braces of the stand feature 4 holes to mount the router table to the stand. Position the stand inverted, on the router table so that the holes are aligned and then mount it with the help of washers and bolts provided, (Finger Tighten). See Figure-3

VEVOR RT017 Router Table - Mounting the stand to the router table

Take the 4 rubber feet out of the package and attach one on each leg. Now, turn the stand up right and your router table is installed on the stand.

Mounting the Router Base Plate in Your Router Table

When mounting a large router, the handles should fit in the same direction as the long opening. Your current router base plate will function as the drilling jig. However, you should determine the optimum router positioning before the base plate. Make sure to take into account the depth adjustment knobs, depth lock levers/knobs and the location of your switch. Place your router in proper inverted position under the table. Then mark with tape on the front edge of the router’s bed plate to verify the position.

Then, remove the screws from the base plate. Locate the top/front of your base plate by observing the position of the starting pin holes. The holes will be to the right of the opening. Again mark with the tape the front and center on the plate to serve as a reminder.

Center the router base plate on the nearest concentric ridge. Then position the mounting holes along the radial lines. Keep the base plate in place with tape. (3 to 4 pieces arranged around the ring should be adequate).

Next, clamp the 2 plates together using C- clamps or wood.

Note: Spring clamps will not provide enough clamping force and could allow the parts to move out of place.

Drill through the new base using a drill bit that matches the size of the holes in your router’s base plate.

Note: If available, perform this operation on a drill press to keep the holes perpendicular.

Important: A piece of wood should be clamped to the front of the router plate whole drilling to avoid splintering of the plate.

After removing the clamps, countersink holes similar to the router’s own base plate. For best result, we recommend a single flute countersink at a slow speed and a drill press if available.

Finally, mount the base plate to the router. If the screws that came with your router are not long enough, longer screws can be purchased at a hardware store or home center in your area.

VEVOR RT017 Router Table - installation process,

Bench Top Router Exploded Diagram

VEVOR RT017 Router Table - Bench Top Router Exploded Diagram

VEVOR RT017 Router Table - Bench Top Router Exploded Diagram

Customers need to assemble it by below parts :

VEVOR RT017 Router Table - Parts name

VEVOR RT017 Router Table - VEVOR logo
Technical Support and E-Warranty Certificate www.vevor.com/support

Documents / Resources

PDF thumbnailRT017 Router Table
User Manual · RT017 Router Table, RT017, Router Table, Table
PDF thumbnailRT017 Router Table
User Manual · RT017, RT017 Router Table, RT017, Router Table, Table

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.