VEVOR RT015 Router Table Instruction Manual

VEVOR__logo

RUTER TABLE

MODEL: RT015

Technical Support and E-Warranty Certificate
www.vevor.com/support

MODEL: RT015

VEVOR RT015 Router Table - 1

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

General Safety Instructions

Extreme caution should be used when operating all power tools. Know your power tool, be familiar with its operation, read through the owner’s manual and practice safe usage procedure at all times.

  • CONNECT your machine ONLY to the matched and specific power source.
  • ALWAYS wear safety glasses respirators, hearing protection and safety shoes, when operating your machine.
  • DO NOT wear loose clothing or jewelry when operating your machine.
  • A safe environment is important. Keep the area free of dust, dirt and other debris in the immediate vicinity of your machine.
  • DISCONNECT the power source when changing drill bits, hollow chisels, router bits, shaper heads, blades, knives or making other adjustments or repairs.
  • ALWAYS keep all safety guards in place and ensure their proper function
  • NEVER reach over the table when the tool is in operation. It is dangerous.
  • ALWAYS keep blades, knives and bits sharpened and properly aligned.
  • NEVER leave a tool unattended while it is in operation.
  • BE ALERT! DO NOT use prescription or other drugs that may affect your ability or judgment to safely use your machine.
  • ALWAYS use push sticks and feather boards to safely feed your work through the machine.
  • ALWAYS make sure that any tools used for adjustments are removed before operating the machine.
  • Always keep the bystanders safely away while the machine is in operation.
Router Table with Fence & Stand
Specific Safety Instructions

Like all power tools and machinery, proper safety and attention must be adhered to. There is danger associated with using any tool or machine so pay careful attention each and every time you use your tool. If you are not familiar with the operations of a router table, you should obtain the advice and/or instructions from a qualified professional.

  • MAKE SURE the router has been installed securely before staring the machine, for safe operation method.
  • NEVER perform any “Free Hand” operation. Do not use your hands to support or guide the work piece. Always use toggle clamp to secure the work piece for cutting.
  • DO NOT wear jewelry or loose clothing while operating this machine.
  • SAFETY GLASSES & RESPIRATOR is highly recommended when working with this machine. Some saw dust can be harmful to your lungs; please take caution when using this machine.
  • ALWAYS feed the work piece to the router bit against the rotation direction.
  • INSPECT your work pieces. Make sure that they are free of nails, staples, tacks, knots and other objects that may be harmful to your router bit.
  • DO NOT jam or try and over push the work piece into the machine during operation. This may cause damage to the machine. Feed the work piece with a firm grasp, slowly and easily and hold the work piece against the fence.
  • MAKE SURE the spindle rotates in the correct direction.
  • DO NOT let anyone stand in front of the machine while operation.
  • TECHNICAL DIFFICULTIES. Any problems you may run into should be carefully looked at with the power OFF and the machine unplugged from the power source.
  • NEVER draw the work piece back during the cutting operation. Stop the router bit before drawing back the work piece.
  • ALWAYS keep bits sharpened and clean.

IMPORTANT: The safety instructions given above can not be complete because the environment in every shop is different. Always consider safety first as it applies to your individual working conditions.

ROUTER TABLE
FEATURES

TABLE TOP

Size: 800*606*36mm
Aluminum Miter Track: 800mm
Table Insert: 306*229mm

FENCE

Size: 460*150mm
Dust Port: 63/77.3/68.2mm
Gaurd: Fluorescent Plastic Plate
Aluminum Miter Track: 460mm
Ruler Label: 456mm

STAND

Made of: Steel
Height: 1025mm
Includes: 4 non-marring Rubber Feet
PHYSICAL FEATURES

VEVOR RT015 Router Table - 2a

  1. Aluminum Miter-Track
  2. Ruler Label
  3. Dust Port
  4. Guard
  5. Aluminum T-Track
  6. Guide Pin
  7. Rubber Feet
  8. Table Insert
  9. Table Top
ASSEMBLY & INSTALLATION

Before assembling the stand, please take a look at the list below. Your stand comes with the following parts and mounting hardware.

  • Short Angle Brace:               2-pcs
  • Shorter Angle Brace:           2-pcs
  • Long Angle Brace:                2-pcs
  • Longer Angle Brace:            2-pcs
  • Round Head Bolt M8x12:  32-pcs
  • Hex Nut M8:                           32-pcs
  • Flat Washer8:                        32-pcs
  • Hex Bolt M6x16:                   4-pcs
  • Flat Washer:                          4-pcs
  • Rubber Feet:                          4-pcs
Stand Assembly

Take the two short and the two longer angle braces out of the box and put it on the floor. Now take the four legs upside down, and attach them to the four braces using 1/4″ x 1/2″ nuts and bolts. (Finger tighten) See Figure-1.

VEVOR RT015 Router Table - Figure-1Figure-1 Attaching legs to the braces

Now, mount the two other longer and the two short angle braces to the legs with the help of the nuts and bolts, (Finger Tighten). See Figure-2

VEVOR RT015 Router Table - Figure-2Figure-2 Attaching the middle braces to the legs

Now, turn the stand upright and adjust the legs so that they are evenly positioned, tighten all the screws well.

Installing the Router Table on the Stand

Take the router table and put it upside down on the floor or bench. The router table and the upper braces of the stand feature 4 holes to mount the router table to the stand. Position the stand inverted, on the router table so that the holes are aligned and then mount it with the help of washers and bolts provided, (Finger Tighten). See Figure-3

VEVOR RT015 Router Table - Figure-3Figure-3 Mounting the stand to the router table

Take the 4 rubber feet out of the package and attach one on each leg. Now, turn the stand up right and your router table is installed on the stand.

Mounting the Router Base Plate in Your Router Table

When mounting a large router, the handles should fit in the same direction as the long opening. Your current router base plate will function as the drilling jig. However, you should determine the optimum router positioning before the base plate. Make sure to take into account the depth adjustment knobs, depth lock levers/knobs and the location of your switch. Place your router in proper inverted position under the table. Then mark with tape on the front edge of the router’s bed plate to verify the position.

Then, remove the screws from the base plate. Locate the top/front of your base plate by observing the position of the starting pin holes. The holes will be to the right of the opening. Again mark with the tape the front and center on the plate to serve as a reminder.

Center the router base plate on the nearest concentric ridge. Then position the mounting holes along the radial lines. Keep the base plate in place with tape. (3 to 4 pieces arranged around the ring should be adequate).

Next, clamp the 2 plates together using C-clamps or wood.

Note: Spring clamps will not provide enough clamping force and could allow the parts to move out of place.

Drill through the new base using a drill bit that matches the size of the holes in your router’s base plate.

Note: If available, perform this operation on a drill press to keep the holes perpendicular.

Important: A piece of wood should be clamped to the front of the router plate whole drilling to avoid splintering of the plate.

After removing the clamps, countersink holes similar to the router’s own base plate. For best result, we recommend a single flute countersink at a slow speed and a drill press if available.

Finally, mount the base plate to the router. If the screws that came with your router are not long enough, longer screws can be purchased at a hardware store or home center in your area.

VEVOR RT015 Router Table - 3
  1. Bit Rotation
  2. Workpiece
  3. Feed Direction
VEVOR RT015 Router Table - 4
  1. Starting Pin Holes
VEVOR RT015 Router Table - 5
If you are unsure about the installation process, please check the installation video.
Stand Parts Break-Down & Parts List

VEVOR RT015 Router Table - 6

NO DESCRIPTION QTY
1 Longer Angle Brace 4
2 Short Angle Brace 2
3 Short Angle Brace 2
4 Short Angle Brace 2
5 Longer Angle Brace 2
6 Round Head Bolt M8 x 12 32
7 Hex Nut M8 32
8 Flat Washer8 32
9 Hex Bolt M6 x 16 4
10 Flat Washer6 4
11 Rubber Feet 4
Router Table Parts Break-Down & Parts List

VEVOR RT015 Router Table - 7

NO QTY PART DESCRIPTION
1 1 Table Top 32” x 24” x 1-3/8”
2 1 Aluminum Miter Track Length 32”
3 11 Flat Head Tapping Screw 4” x 1/2″
4 4 Nut M 1/4” x 1/2″
5 2 Aluminum T-Track Length 11-3/4”
6 4 Hex Socket Set Screw 6 x 6
7 1 Insert + Guide Pin 9” x 12”
Fence Parts Break-Down & Parts List

VEVOR RT015 Router Table - 8

NO QTY PART DESCRIPTION
1 1 L-Aluminum 4” x 4” x 33”
2 1 Adapter 2-1/2” x 2”
3 2 Pan-Head Machine Screw 1/4” x 1”
4 1 Dust Port 2-1/2” x 3”
5 2 Triangle Knob 1/4″
6 4 Aluminum-Miter Track Length 18”
7 2 Hex Bolt 5/6″ x 1″
8 20 Flat Head Tapping Screw 4# x 1/2″
9 2 Fence 18” x 6” x 1”
10 1 Bit Cover Fluorescent Plastic Plate
11 4 Hex Bolt 5/16” x 1”
12 6 Knob 5/16”
13 2 Ruler Label Length 18”
14 2 Flat Washer 1/4″
15 2 Pan-Head Machine Screw 3/16“x 2-1/4”

Customers need to assemble it by below parts :

RT015: Part name Quantity
1. Round Head Bolt M8 x 12 32
2. Hex Nut M8 32
3. Flat Washer8 32
4. Hex Bolt M6 x 16 4
5. Flat Washer6 4
6. Knob 5/16”+Hex Bolt 5/16” x 1”+Flat Washer 5/16” 6
7. Knob 1/4”+Hex Bolt 1/4” x 1”+Flat Washer 1/4” 2
8. Pan-Head Machine Screw 3/16“x 2-1/4” 2
9. Ruler Label Length 18” 2
10. Bit Cover Fluorescent Plastic Plate 1
11. Dust Port 2-1/2” x 3” 1
12. Adapter 2-1/2” x 2” 1
13. Fence 18” x 6” x 1” 2
14. Table Top 32” x 24” x 1-3/8” 1
15. Insert + Guide Pin 9” x 12” 1
16. Aluminum Miter Track Length 32” 1
17. Longer Angle Brace 2
18. Short Angle Brace 2
19. Short Angle Brace 2
20. Short Angle Brace 2
21. Longer Angle Brace 4
22. M3 hex wrench 1
23. Rubber Feet 4
24. Position axis 1
25. M4 * 16 countersunk cross bolt * 4 (with fixed router screw) 4

VEVOR logo___A
Technical Support and E-Warranty Certificate
www.vevor.com/support

Documents / Resources

PDF thumbnailRT015 Router Table
Instruction Manual · RT015, SF-808, RT015 Router Table, RT015, Router Table, Table
PDF thumbnailRT015 Router Table
Instruction Manual · RT015, SF-808, RT015 Router Table, RT015, Router Table, Table

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.