VEVOR OT109 Switch Panel Instruction Manual

VEVOR OT109 Switch Panel

Specifications

Quick Setup & Use

1. Read before operating: Review all manual instructions carefully.
2. Choose the mounting method for the control box: Fix mount bracket or flush mount (ensure clearance behind the drilling location and do not drill into wiring harnesses/components).
3. Mount the switch panel: Use the adjustable-angle mount bracket or the flush mount bracket; use the supplied screw accessories to fix the bracket.
4. Plan cable routing: Ensure the control wire and extension plug-and-play wire are long enough for your chosen location and that wiring clearances are adequate.
5. Wire the auxiliary devices: Connect the switch panel to up to 12 auxiliary LED lights/electrical devices. Confirm lamps are correctly connected before connecting the power cable.
6. Turn on the switch panel: The red indicator light is on when the switch panel is on.
7. Select a lighting mode: Choose the mode so the indicator shows the corresponding color (Red = Toggle, Blue = Momentary, Green = Pulsed).
8. Operate the buttons: For the momentary mode (Blue indicator), press and hold to turn the light on; release to turn it off.
9. Backlight behavior: The switch panel backlight brightness automatically adjusts to ambient brightness (dimmer in dark areas; brighter in bright areas).

Description

This is the original instruction; please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us; we won’t inform you again if there are any technology or software updates on our product.

	Warning: To reduce the risk of injury, the user must read the instruction manual carefully.
	This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.

This product is subject to the provisions of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices

SAFETY INSTRUCTION

WARNING:

• Auxiliary off-road lights FOR OFF-HIGHWAY USE ONLY. Do not operate on public roads; may violate local traffic laws.
• Turn OFF all switches after vehicle shutdown to prevent battery drain. WARNING: High-intensity light may cause eye damage. Do not stare directly into the lamp.
• Disconnect vehicle battery before wiring installation to avoid short circuit & fire hazard.
• Do not overload circuit; risk of overheating & fire.

NOTICE: Turn off extra lights during oncoming traffic to prevent glare accidents.

PACKING LIST

Product Features

• Control 12 auxiliary LED lights or electrical devices
• Colorful LED background lighting
• Lighting modes control,Press and hold for 3 seconds,background light automatically switches colors.
• Automatic Backlight brightness adjustment
• ON/OFF switch or momentary press operation
• 80 Labels/stickers/decals design + DIY

SWITCH PANEL INDICATION

BACKLIT BRIGHTNESS DIMMABLE
The backlit brightness of the switch panel is automatically dimmable according to the brightness variation of the surroundings/ environment.

In the tunnel or other dark places, the switch panel will be dim ,reduce the impact on the driver’s vision.

On the road or other bright places, the switch panel will be brighter, making it easier to control.

80PCS REUSABLE SWITCH L ABELS

1. Thoroughly clean the switch panel.
2. Peel off the label and firmly press down on the switch panel.
3. Multi-function labels for DIY your specific needs. (80 icons)

CONTROL PANEL WORKING MODE

• 3 lighting modes for you to choose from, and different colors represent different working modes:
• Red: Toggle
• Blue: Momentary
• Green: Pulsed
• Blue: Momentary. Press & hold to tum on the light and release to turn off the lights.

LIGHTING MODE SETTING
The red indicator light is on when the switch panel is on. When you select the mode, the indicator will show the color of the corresponding function.

MOUNTING THE CONTROL BOX

• TWO different installation methods are available:
• Fixed mount bracket
• Flush mount
• The ideal mounting of the control box should allow for an unobstructed path for the power wires, accessory wires, and the control harnesses included.
• If you decide to drill, please check the clearance behind the drilling location. Make sure you are not going to drill through and damage any wiring harnesses and components of the vehicle.

Fix Mount
Using the mounting bracket as a guide, find a good and desired location to mount the control box.

Flush Mount
Using the control box as a guide, find a good and desired location to mount.

SWITCH PANEL MOUNTING

• TWO different installation methods are available; the mounting bracket angle is adjustable:
• Angle-adjustable mount bracket flush mount bracket
• Attach the switch panel to the mount bracket you need, then use the supplied screw accessories to fix the bracket.
• The ideal thickness of the mounting surface should be between 1/8″ to1/4″. Check to make sure the control wire and extension plug&play wire is long enough to mount in the desired location.
• Check the clearance behind the installation location. Make sure you are not going to drill through and damage any wires and components of the vehicle.
• Once you decide where to mount, use the bracket to mark the drill location. After the installation of the panel, proceed to the wiring installation.

Angle Adjustable Mount

Flush Mount

SWITCH ASSEMBLY WIRING DIAGRAM

High Temperature Malfunction Indicator
If the operating temperature of the equipment exceeds the system set value, the indicator light at the center of the control board illuminates, accompanied by a buzzing alarm. The system locks up and shuts down automatically. When the temperature drops below the preset threshold, the indicator light turns off, the buzzing sound ceases, and the system resumes normal operation. Single Circuit Malfunction Indicator: A red light next to the fuse clip lights up in the event of a single circuit failure.

Connect to 12 auxiliary LED lights or electrical devices

• Total power will go up to 1000W at 12V, 1500W at 24V, and the maximum current is 80A.
• The maximum output current of ground 1&7 is 30A; the maximum output current of ground 2/3/8/9 is 20A.
• The maximum output current of ground 4/5/10/11 is 10A.
• The maximum output current of ground 6&12 is 5A.
• 1/2/3/4/ 5/ 6/8/ 9/ 10/ 11/ 12: The designed maximum output current is 20A.
• The maximum output current of grounds 1 & 7 is 40A.
• Make sure all the lamps are correct before connecting the power cable.
  

Troubleshooting

High-temperature malfunction indicator (center of control board)

• Symptom: If the operating temperature exceeds the system set value, the center indicator illuminates and a buzzing alarm sounds.
• What happens next: The system locks up and shuts down automatically.
• Recovery: When the temperature drops below the preset threshold, the indicator turns off, the buzzing stops, and normal operation resumes.

Single-circuit malfunction indicator (next to fuse clip)

• Symptom: A red light next to the fuse clip lights up when there is a single circuit failure.
• Action: Review the connected auxiliary device/circuit associated with that single circuit and address the failure, then restore operation (the manual text identifies the indicator and failure condition but does not provide additional reset steps).

Support Center