VEVOR OOT044S Switch Panel Instruction Manual

VEVOR OOT044S Switch Panel

Overview

VEVOR OT044S is a switch panel designed to control 8 auxiliary LED lights or electrical devices, with colorful background lighting, automatic/dimmable backlight, and selectable lighting/load behavior.

Specifications

• Backlight: automatically dimmable based on surrounding brightness
• Lighting mode: optional background light off
• Labels: 80 re-usable switch labels (DIY icons)

Quick Setup / Use

1. Read the manual instructions carefully before operating.
2. Confirm the control box and switch panel installation location; ensure clearance behind the drilling area so you do not damage wiring harnesses/components.
3. Mount the control box using either fix mount (mounting bracket) or flush mount method.
4. Mount the switch panel using either an adjustable-angle mounting bracket or a slim-line flush mount bracket; the ideal mounting surface thickness is 1/8 to 1/4.
5. Ensure the control wire and extension “plug & play” wire are long enough for the chosen location.
6. Wire and connect to up to 8 auxiliary LED lights/electrical devices; ensure all lamps are connected before connecting the power cable.
7. Turn OFF all switches after vehicle shutdown to prevent battery drain.
8. To turn off the background light: press the OFF/ON key (this turns OFF both load switches at the same time and retains the last memory function).

SAFETY WARNING

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

• Warning-To reduce the risk of injury, user must read instructions manual carefully.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.
• This product is subject to the provision of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices

SAFETY INSTRUCTION

• WARNING: Auxiliary off-road lights FOR OFF-HIGHWAY USE ONLY. Do not operate on public roads, may violate local traffic laws.
• WARNING: Turn OFF all switches after vehicle shutdown to prevent battery drain.
• WARNING: High-intensity light may cause eye damage. Do not stare directly into lamp.
• WARNING: Disconnect vehicle battery before wiring installation to avoid short circuit & fire hazard.
• WARNING: Do not overload circuit, risk of overheating & fire.
• NOTICE: Turn off extra lights during oncoming traffic to prevent glare accidents.

 PACKING LIST

PRODUCT FEATURES
Control 8 auxiliary LED lights or electrical devices Colorful LED background lighting Automatic + Manual Backlight brightness adjustment ON/OFF switch or momentary press operation 80 Labels / stickers / decals design + DIY

SWITCH PANEL INDICATION

BACKLIT BRIGHTNESS DIMMABLE
The back lit brightness of the switch panel is automatically dimmable according to the brightness variation of the surroundings/ environment.In the tunnel or other dark places, the switch panel will be dim ,reduce the impact on the driver’s vision.On the road or other bright places, the switch panel will be brighter,make you control it more easier.

80PCS REUSABLE SWITCH L ABELS

1. Thoroughly clean the switch panel.
2. Peel off the lable and firmly press down on the switch panel.
3. Multi-function labels for DIY your specific needs. (80 icons)

LIGHTING MODE SETTING Turn off the background lightPressing the OFF/ON key will turn OFF both load switches at the same time and retain the last memory function

MOUNTING THE CONTROL BOX
TWO different installation methods are available: Fix mount bracket Flush mount The ideal mounting of the control box should low for an unobstructed path for the power wires, accessory wires and the control harnesses included. If you decide to drill, please check the clearance behind the drilling location. Make sure you are not going to drill through and damage any wiring harnesses and components of the vehicle.

• Fix Mount
  Using the mounting bracket as a guide, find a good and desired location to mount the control box.
• Flush Mount
  Using the control box as a guide, find a good and desired location to mount.

SWITCH PANEL MOUNTING
TWO different installation methods are available mounting bracket angle is adjustable:Angle-adjustable mount bracket Slim line flush mount bracket Attach the switch panel to the mount bracket you need, then use the supplied screw accessories to fix the bracket. The ideal thickness of the mounting surface should be between 1/8″ to 1/4″.Check to make sure the control wire and extension plug&play wire is long enough to mount the desired location. Check the clearance behind the installation location. Make sure you are not going to drill through and damaged any wires and components of the vehicle. Once you decide where to mount, use the bracket to mark the drill location. After the installation of the panel, proceed to the wiring installation.

Angle Adjustable Mount

SWITCH ASSEMBLY WIRING DIAGRAM

High Temperature Malfunction IndicatorIf the operating temperature of the equipment exceeds the system set value, the indicator light at the center of the control board illuminates accompanied by a buzzing alarm. The system locks up and shuts down automatically. When the temperature drops below the preset threshold, the indicator light turns off, the buzzing sound ceases, and the system resumes normal operation. Single Circuit Malfunction Indicator A red light next to the fuse clip lights up in the event of a single circuit failure.

Connect to 8 auxiliary LED lights or electrical devices

• Total power will go to 600w at 12V, 1200W at 24V and the maximum current is 60A.
• The maximum output current of ground 7 & 8 is 30A, the maximum output current of ground 1-6 is 20A.
• The recommended connection method is to increase the current gradually from ground 1 to ground 8.
• Make sure all the lamps are connected before connecting the power cable.

Troubleshooting

• High temperature malfunction (high temperature indicator + buzzer): If the equipment operating temperature exceeds the system set value, the center indicator light illuminates and a buzzing alarm sounds; the system locks up and shuts down automatically. When temperature drops below the preset threshold, the indicator turns off, buzzing stops, and normal operation resumes.
• Single circuit malfunction (single circuit indicator): If a single circuit failure occurs, the red light next to the fuse clip lights up.