VEVOR CX-01 Bakery Display Case User Manual

Step 3: Install the rear cover plate on the frame where the left and right support plates have been installed using screw assembly L.
Step 5: Put the tray into the frame.

Step 6: Install the silicone base foot at the 4 corners of the bottom. Install the tray.

Cleaning Instructions:
For cleaning, wipe the surface with a damp (not wet) cloth or wipe dry with a clean lint-free cotton cloth.

FAQ

Q: Where can I get technical support or warranty information?
A: For technical support and e-warranty certificate, visit www.vevor.com/support.

Q: How do I ensure that I have all the parts for assembly?
A: Please identify each part in the parts list provided and check to ensure that all parts are accounted for before assembly.

Thanks for purchasing one of our products.
Please read the assembly instructions carefully before the installation. NEED HELP? CONTACT US!

Have product questions? Need technical support? Please feel free to contact us:
Technical Support and E-Warranty Certificate www.vevor.com/support

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

ASSEMBLY PRECAUTIONS

Assemble needs to follow these instructions. Incorrect assembly can be a hazard.

Wear safety goggles and heavy-duty work gloves during assembly.
Do not assemble when tired or under the influence of alcohol, drugs or medication.

Weight capacity and other product capabilities only apply to a properly and completely assembled product.
Keep the assembly area clean and well-lit.

Keep bystanders out of the area during assembly.

USE PRECAUTIONS

WARNING: TO PREVENT SERIOUS INJURY AND DEATH FROM TIPPING:

This product is not a toy. Do not allow children to play with or approach this item.
Use as intended only. Do not sit or stand on the product.
Inspect before every use. Do not use it if parts are loose or damaged.
Use on flat, level, and hard surfaces only.
Do not exceed the listed weight capacity. Tighten all knobs securely before applying load. Be aware of dynamic loading! The sudden load movement may briefly create an excess load, causing product failure.

PRODUCT PARAMETERS

Model	Product Size(in)	Bandejas extraíbles（Quantity）	Bandejas extraíbles（Size）
CX-01	20.6×15.5×11.9	2pcs	20″x13″

PARTS LIST

NOTE: Part not shown to actual size.

QTY	DESCRIPTION
1	Base Plate
1	Left Side Seal Plate
1	Right Side Seal Plate
1	Top Plate
1	back board
1	Righ tside door
1	Left side door
3	Door handle
4	Hinge
2	Tray
12	Bolt M4*15
2	Screw Assembly M4*15
22	Bolt M4*10
28	Nut M4
2	Inner Hexagon Spanner （different sizes)
4	Silicone bottom foot

Please identify each part and check to ensure that all are accounted for.

ASSEMBLY STEPS

STEP 1
Install the left and right bracket panels on the bottom plate, pay attention to distinguish the left and right panels.The screw assembly used is M4×15.
STEP 2
Install the top on and above the frame.The screw assembly used is M4×15.
STEP 3
Install the rear cover plate on the frame where the left and right support plates have been installed.The screw assembly used is “L”.
STEP 4
Install the left and right sealing door panels on the frame, and pay attention to distinguish between the left and right door panels.The screw assembly used is M4×10.
STEP 5
Put the tray into the frame
STEP 6
Install the silicone base foot at the 4 corners of the bottom. Install the tray.

Cleaning

For cleaning, wipe the surface with a damp (not wet) cloth or wipe dry with a clean lint free cotton cloth.

Manufacturer: Shanghaimuxinmuyeyouxiangongsi
Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia