VEVOR AB-720 Cutting Plotter Instruction Manual

VEVOR AB-720 Cutting Plotter

Product Information

This cutting plotter is designed for precise cutting of various materials. It comes in multiple models with specific features tailored to different cutting needs. Please read the user manual carefully before operating.

Product Usage Instructions

Basic Safety Rules

• Maintenance and operation should not be done by childrenwithout supervision.
• Close supervision is necessary when the appliance is used near children.
• Do not immerse cords, plugs, or appliances in water or other liquids to prevent fire or electric shock.

Blade Safety

The blade is sharp. Avoid touching it directly with your hand to prevent injury. Use caution when handling the blade.

Matters Needing Attention

Follow the instructions carefully to prevent damage to the plotter:

• Ensure safe use methods and pay attention to warnings toprevent injury or machine damage.
• Do not allow the plotter to come into contact with liquids or metal objects.
• Do not damage or replace the power cord; avoid bending or pulling it excessively.
• Place the plotter on a stable surface to prevent falls.
• Unplug the power cord from the socket if the plotter will not be used for an extended period.
• Avoid using the plotter during thunderstorms to prevent lightning damage.
• Check power supply voltage and cable condition before plugging in the device.

Contents

1. Protective material must be removed before turning on the cutting plotter.
2. Check the label on the back of the plotter to match the required voltage with the power supply voltage.
3. Ensure the power switch is off before plugging into a grounded power outlet.

Frequently Asked Questions

Loading PDF…

−+Fit width100%View FullscreenDownload PDFPrint PDF

×

Loading PDF…

CUTTING PLOTTER
MODEL:AB-720, B-720,KH-720A, KI-720S, KW-720D, KW-720S, KW-720, SK-720L, SK-720T, B870, KH-870A, KI-870A, KI-870S, KW-870D, KW-870, SK-870T, SK-870, KW-870S, AB-1350, B-
1350, KH-1350A, KI-1350A, SK-1350, KH-375A

CUTTING PLOTTER
MODEL:AB-720, B-720,KH-720A, KI-720S, KW-720D, KW-720S, KW-720, SK-720L, SK-720T, B870, KH-870A, KI-870A, KI-870S, KW-870D, KW-870, SK-870T, SK-870, KW-870S, AB-1350, B1350, KH-1350A, KI-1350A, SK-1350, KH-375A
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

.Bacic Safety Rules
WARNINGRead all safety warnings, instructions, illustrations and specifications provided with this appliance. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. 1.Protective material must be removed before turning on the cutting plotter. 2.Check the label on the back side of the plotter to confirm that the rated voltage required by the plotter matches the voltage of the power base. 3.Firstly make sure that the power switch is off, then plug the power supply into grounded power outlet. 4.Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions, or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment. 5.Type X attachment: If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent. 6.Please do not touch the power cord with wet hands to avoid electric shock. 7.Please only use the power cord, data cable provided with this product, or manufacturer-approved replacements. 8.Do not use outdoors. INDOOR USE ONLY 9.Please do not drop metal objects and liquids into the machine to avoid malfunction. 10.After shutting down, you must wait another 5 seconds to turn on the cutting plotter again, otherwise it will cause damage to the cutting plotter. 11.In thunderstorms, turn the power switch to OFF and unplug the power cord. 12.Please do not privately change the manufacturer’s components. 13. Manufacturer reserves the right to change product specifications without prior notice. 14.The manufacturer only bears the legal obligations of the product itself sold to the users, and does not bear other losses caused by the malfunction of the products. 15 . Without our company’s permit, no part of this manual can be copied or transmitted in any name.

16.Do NOT drag the carriage by hand. 17. If there is an abnormal sound after powering on the machine, please turn off the power immediately and contact the after-sales department for feedback. 18.This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision. 19.Close supervision is necessary when any appliance is used by or near children. Children shall not use the appliance. Cleaning and user maintenance shall not be made by children. 20.To protect against fire, electric shock, or personal injury, do not immerse cords, electric plugs, or appliances in water or other liquids.
21 . WARNING:
SA”Blade is very sharp.Please do not touch the blade directly with your
hand, otherwise, your finger will be injured and the tip will be blunt. and hold the arbor on the blade when you remove it.

.Matters needing attention
To ensure that the operator can correctly use the plotter to prevent damage to the plotter, please follow the instructions with the following marks.

1.Ensure safe use methods warning

Improper operation can result in injury. Improper operation may cause damage to the machine.

Pay attention to

Improper operation may result in personal injury or damage to other objects.

2.Symbol Description warning
Symbol indicates that users need to pay close attention. The picture on the left means “Be careful of electric shock”.
Do not use a power supply that does not meet the rated voltage. Using an unqualified power supply can cause fire or electric shock. If the machine gives out smoke, smell, noise and other abnormal circumstances, please power off immediately, do not use. Use in this condition can cause fire or electric shock. Do not plug or remove the power plug when the power is on. Unplugging the power plug while the power is on will damage the machine. Ensure machine grounding. Electrical shock or mechanical failure if not grounded. Do not disassemble, repair or rectify the machine. Do like this will result in fire or electric shock, resulting in personal injury. Pay attention to
The machine can not penetrate into liquids, fall into metal objects, etc. These objects can cause fires.
Do not destroy or replace the original power cord, and do not allow the power cord to be excessively bent, pulled, tied or pressed under heavy objects. Do like this could damage the power supply, cause an electric shock or cause a fire. If the cutting plotter will not be used for a long time, please unplug the power cord from the socket. Otherwise it will cause a fire.

When operating, do not put your hands on the reel. This may cause injury.

The machine should be placed on a stable surface. Otherwise the machine will fall, resulting in injury.
When unplugging the power cord from the socket, the plug should be pulled, not the cable. Pulling on the cable can cause electric shock or fire.
It is prohibited to use in thunderstorms and lightning weather. To avoid lightning damage to the machine.

Before inserting the power plug, check
whether the power supply voltage and power cable are normal. Make sure there are no exceptions before you plug in the device.

Precautions

1. Protective material must be removed before turning on the cutting plotter.
2. Check the label on the back side of the plotter to confirm that the rated voltage required by the plotter matches the voltage of the power base. 3. Firstly make sure that the power switch is off, then plug the power supply into grounded power outlet.
4. Please do not touch the power cord with wet hands to avoid electric shock.
5. Please only use the power cord, data cable provided with this product, or manufacturer-approved replacements. 6. Please do not drop metal objects and liquids into the machine to avoid malfunction. 7. After shutting down, you must wait another 5 seconds to turn on the cutting plotter again. Otherwise, it will cause damage to the cutting plotter. 8. In thunderstorms, turn the power switch to OFF and unplug the power cord. 9. Please do not privately change the manufacturer’s components. 10. Manufacturer reserves the right to change product specifications without prior notice. 11. The manufacturer only bears the legal obligations of the product itself sold to the users, and does not bear other losses caused by the malfunction of the products. 12. Without our company’s permit, no part of this manual can be copied or transmitted in any name. 13. Do NOT drag the carriage by hand. 14. If there is an abnormal sound after powering on the machine, please turn off the power immediately and contact the after-sales department for feedback.
2

Introduction for main parts

KH Model
1. Cover for rail guide 3. Roller for feeding paper 5. Reset switch 7. Buttons 9. Blade clamp

2. Pinch roller kit 4. Carriage 6. Screen 8. The right cover
10. The left cover

Left side

Right side

11.Power connection 12.Fuse holder 13.Power switch 14.USB port 15.COM port

3

KI Model
1. Cover for rail guide 3. Roller for feeding paper 5. Screen 7. The right cover 9. Blade clamp

2. Pinch roller kit 4. Carriage 6. Buttons 8. Reset switch 10. The left cover

Left side

Right side

11.Power connection 12.Fuse holder 13.Power switch 14.USB port 15.COM port

4

EH Model 1. Cover for rail guide 3. Roller for feeding paper 5. Reset switch 7. Buttons 9. Blade clamp

2. Pinch roller kit 4. Carriage 6. Screen 8. The right cover
10. The left cover

Left side

Right side

11.Power connection 12.Fuse holder 13.Power switch 14.USB port 15.COM port 16.U-disk port

5

SK Model
1. Cover for rail guide 3. Roller for feeding paper
5. Screen 7. The right cover 9. Blade clamp

2. Pinch roller kit 4. Carriage 6. Buttons 8. Reset switch 10. The left cover

Left side

Right side 6

11.Power connection 12.Fuse holder 13.Power switch 14.USB port 15.COM port

. Technical parameters

Mod el Item

720

870

1350

Max. feeding width Max. cutting width Cutting thickness
Speed/Pressure Buffer
LCD display Real- time Speed adjusting Interface Re-cutting function Re-cutting accuracy Language format Voltage

720mm 615mm

870mm 765mm

1350mm 1245mm

1mm

20-800mm/s

20-500g

1-4M CN/ EN

Support

COM+USB / COM+USB+U-DISK Support ±0.1mm
DMPL/HPGL AC85-264V 50/60Hz MAX100W

To protect the machine, use only the accessories in this accessory box

Product explosion diagram

1-4 AI bracket assembly diagram
2-1 Install the machine on the bracket
12

. Blade assembly

1 Unscrew the cap from the blade carriage.

2 Set the brass ring on the blade carriage to the fully down position.

3 Remove the protective cover from a new blade.

4 Insert the blade into the top of the blade carriage.

5 Screw the cap back onto the blade carriage.

6 Adjust the carriage cap until the blade is protruding approximately 1/64 of an inch.

7 Adjust the brass ring until it fits snugly against the cap. This will help
keep the cap in place during operation.

Blades should be replaced every 6 months. Your blade may need to be replaced more often if you are cutting thicker material, such as flock, glitter, or reflectives.
13

1) . Assemble the blade into the holder. See as below:

(Appearance view)

(Exploded view)

2). Loosen the blade adjustment nut and rotate the shank to adjust the length of the exposed blade tip. Determine the tip length according to the thickness of the material.

Correct

Blade tip is too long

Blade tip is too short

3Press the pressing rod when you want to change the blade. Take out the blade when it is exposed.

Tips: Do not touch the blade tip by finger. Otherwise, your finger will be injured and the tip will be blunt.
14

CARRIAGE SLOT

Holds the blade carriage in place.

LOCKING KNOB

Allows access to the blade/pen carriage slots for exchanging/replacing carriages.

1 Loosen the locking knob on the carriage arm.

2 Place the blade carriage into the carriage arm.

3 Tighten the locking knob on the carriage arm.

15

How to use the product

KI Model SK Model

EH Model

KH Model

The main screen of the cutter allows you to set the main settings of the cutter including the cutting speed and cutting force options. It also allows you to cut a test
pattern or check the amount of force that is currently set.

16

Reset BUTTON Offline/Leave/Option BUTTON SETUP BUTTON TEST/Move BUTTON
ORIGIN BUTTON V+ / V- BUTTONS
F+ / F- BUTTONS

Resets by stopping the cutter, and setting the
origin of the carriage arm to its rightmost position. Accesses the Offline/Pause mode. Accesses the Setup mode.
Will cut a small test shape so that the current force and speed settings of the cutter can be tested. You can use this to determine the proper cutting speed and force settings needed for different materials without wasting large amounts of material from cutting full designs.
Used to test z-axis functionality (by dropping the blade down if the carriage is functioning properly) or to set a new origin point when the machine is in its Offline mode
Adjusts the cutting speed. A cutting speed of 300 mm/s is a reasonable default speed that can be used for most cuts. When working with smaller and more detailed images, a slower speed may be required. When working with larger and less detailed images, a higher speed can be used to shorten the operation time.
Adjusts the cutting force. A cutting force of 100g is a good general starting place to work from when trying to determine the force needed for a specific material. All cuttable materials
will differ in the amount of force needed so proper testing should always be made to determine the amount of force to use. The amount of force used should be enough to fully penetrate the material to be cut while not enough to cut through the backing material.

17

KI Model SK Model

EH Model

KH Model

Offline mode is used to reposition the cutting material and blade so that a new starting position can be set for the next design. Offline mode can also be accessed while the cutter is in operation and will pause the current cutting process. Although changes can be made to the material and blade positions if Offline /Pause mode is accessed during cutting, making changes to either setting is not normally
recommended.
18

Reset BUTTON Offline/Leave/Option BUTTON
SETUP BUTTON TEST/Move BUTTON
ORIGIN BUTTON
V+ / V- BUTTONS F+ / F- BUTTONS

Resets by stopping the cutter, and setting the
origin of the carriage arm to its rightmost position. Ignores any changes that have been made to the material or blade positions and exits Offline/Pause mode, returning the cutter to the main screen. Resumes any cutting that was taking place when Offline/Pause mode was entered.
Has no function in this mode. Accepts any changes that have been made to the material or blade positions and exits Offline /Pause mode returning the cutter to the main screen. Resumes any cutting that was taking place when Offline /Pause mode was entered from the new blade/material positions.
Accepts any changes that have been made to the material or blade positions and exits Offline /Pause mode returning the cutter to the main screen. Resumes any cutting that was taking place when Offline /Pause mode was entered from the new blade/material positions.
Reposition the material by moving the feed rollers. After movements are made, you can confirm the changes by pressing the TEST or ORIGIN buttons or cancel by pressing the
OFFLINE/PAUSE button.
Reposition the blade by moving the carriage arm. After movements are made you can confirm the changes by pressing the TEST or ORIGIN buttons or cancel by pressing the OFFLINE/PAUSE button.

19

1. Place the roll on top of the stand rollers. For heat press vinyl, please flip the roll.
2. Release the pinch rollers release levers.
3. Feed the vinyl underneath the pinch rollers (if working from a single sheet instead of a roll, the vinyl can also be fed from the front). 4. Adjust the pinch rollers so there is one roller located on each side of the vinyl (and, on models with 3 or more rollers, one roller near the center). Avoid lowering a pinch roller to the gap between the two feed rollers.
20

5. Leave a gap of between1/2″-1 1/2″ from the edge of the roller and the edge of the vinyl on both sides.
6. Engage the Pinch Rollers by pushing down on the Pinch Roller Release Levers.
If the cutter is not already on, turn it on now.
If you would like to change the position of where the cut will be made:
1. Press the OFFLINE/PAUSE button to enter offline mode. 2. Adjust the vinyl to where you want to make your cut to start by using the Up and Down arrow keys on the control panel.
21

3. Now, adjust the blade to where you want your cut to start by using the Left and Right arrow keys. 4. Now press the Origin button to tell the cutter that this is the location where you would like the cut to begin.
22

How to connect products to software
Attach the power cord to the cutter and then plug in the unit and turn on the power.
INSTALLING VINYL MASTER SOFTWARE It comes bundled with SignMaster software, an easy-to-use software with the tools to help you take your projects from concept to a ready-to-cut computer image file. The driver is automatically installed during software installation. You do not need to install the driver separately.
23

. Software and driver installation
1. First download the installer via the link below
https://get.signmaster.software

(pic 1)

(pic 2)

2. Double click to open the downloaded application.( pic 3)

(pic 3)

3. After opening optical drive, click Install Software (pic 4)

Click on the icon in the red box

Select the language

24

Enter the PSN code

Agree to click next

Default installation path, click next
(pic 4-5) 25

Select the unit
(pic 4-6) Select machine model

(pic 4-7)

T he selected m ach in e m odelcan be view ed in the labelabove the m ach in e p ow er socket

26

Next
(pic 4-8) The installation is complete
(pic 4-10) 27

This activation window appears when you open the software
(pic 4-11) Click activate and enter your email twice
(pic 4-12) 28

Activation successful, exit
(pic 4-13)
. Connection of software and machine
1.Open the software, select cut content, and click send to the cutting plotter Click the cutter icon in the red box
(pic 5-1)
29

Click properties

Click connect

(pic 5-2)

(pic 5-3) Select machine model

(pic 5-4) Select Direct USB Port
30

(pic 5-5) Drop-down select driver

Click finish

(pic 5-6) Click cut now

(pic 5-7)

(pic 5-8) 31

Click cut now
(pic 5-9)
The output is completed, the cutting plotter is cutting
(pic 5-10) Note: Specific operation can refer to USB flash drive operation video, including as follows 1. Ordinary cutting video 2. Automatic contour video 3. Automatic deviation correction video 4. Software installation video
.Troubleshooting
1.The computer does not have the CD drive cannot load the CD installation software how to do.
32

Solution: The software installation package is included in the usb flash drive. You can also download the software from the following link:https://fcws6.com/downloads/signmaster/SignMaster_UniverDSR_35_GW.exe
2. Product cannot connect to software. Solution:Software port Settings, as shown below:

3.Paper deviation occurred during cutting.
Solution: Because the tension of paper press is inconsistent, rotate the two yellow copper nuts on each paper press to the same height, then the pressure is balanced, as shown below:

High inconsistency

Rotate to the same height

4.The effect of small graphics cutting is not ideal. Solution: When the cutting height is 3-5 mm letters, the software compensation value is set to 0.45 and the speed is adjusted to 400mm/s. When the cutting height is more than 5 mm letters, the software compensation value is set to 0.3 and the speed is adjusted to 600 mm/s or more.

33

5.Often repeated cutting, cutting before automatic paper and other problems. Solution: Cancel the automatic paper feeding function after cutting in the software, as shown below:
6.The cutting process stops and does not return to the origin. Solution:Do not use any data conversion connector. Data may be lost and the cutting process may stop. Please plug the data line directly into the computer interface.
34

FCC Information
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment! This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This product may cause harmful interference. 2)This product must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this product not expressly approved by
the party.responsible for compliance could void the user’s authority to operate the product.
Note: This product has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this product does cause harmful interference to radio or television reception,which can be determined by turning the product off and on, the user is encouraged to try to correct the interference by one or more of the following measures. · Reorient or relocate the receiving antenna. · Increase the distance between the product and receiver. · Connect the product to an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for assistance.
35

VIIII CORRECT DISPOSAL
This product is subject to the provision of European Directive 2012/19/EC.
The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol. Products marked as such may not be discarded with normal domestic waste, but must be taken to a collection point for recycling electrical and electronic devices.
Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. EC REP: E-CrossStu GmbH. Mainzer Landstr.69, 60329 Frankfurt am Main. UK REP: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730