VEVOR 69300007 Impact Socket Set

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.
Safety Warnings and Precautions
WARNING:
- Usage Risk: Improper use or incorrect tool selection can cause slipping, rounding of fasteners, or tool breakage, leading to personal injury or equipment damage.
Use as intended only. The Impact Socket Set is not a toy, and it cannot be played by children to prevent children from eating it by mistake.
The Impact Socket Set cannot be used to injure people maliciously. Flammable: Keep away from open flame. This product box will ignite and burn if brought into contact with an open flame.
Keep away from sharp points, blades and other items, so as not to scratch the product box. - Electrical Hazard: When working on or near live electrical equipment, always use certified insulated tools and ensure the power is disconnected.
- Protection Required: Always wear safety glasses when operating these tools. Additional protective equipment (gloves, etc.) is required in environments with risk of flying debris, dust, or chemical splash.
- No Modification: Never modify tools by heating, welding, grinding, etc. This severely compromises their strength and can lead to catastrophic failure.
Safety Precautions
- Installation and Inspection Notes
Before First Use: Upon unboxing, verify contents against the checklist. Inspect all tools for shipping damage, cracks, or rust.
Pre-Use Check: Before each use, inspect tools (especially load-bearing areas of wrenches and sockets) for visible wear, cracks, or deformation. Check that the ratchet’s reversing mechanism functions correctly. Matching Principle: Always select a tool that precisely matches the size of the bolt/nut. Using an oversized tool or extending the handle (e.g., with a pipe) can cause overload and tool failure. - Environmental Conditions
Work Area: Keep the work area clean, tidy, and well-lit. Avoid operating tools in wet, oily, or cluttered environments to prevent slips or oily tools from causing a loss of grip.
Explosive Atmospheres: In environments where flammable gases or dust may be present, never use standard steel tools that can create sparks. Use non-sparking (e.g., beryllium copper, aluminum bronze) tools.
Corrosive Environments: Clean tools promptly after use to remove sweat, oil, and corrosive substances to prevent rust. - Maintenance, Shelf Life & Storage
Routine Care: Wipe tools with a clean cloth after each use. Apply a few drops of dedicated tool oil periodically to moving parts.
Deep Maintenance: Conduct a thorough cleaning, inspection, and lubrication of the entire kit quarterly.
Shelf Life/Service Life: With normal use, avoidance of overload, and proper care, the main tools have a service life of 10+ years. Consumables lifespan depends on frequency of use and material hardness.
Storage: Store cleaned tools in a dry toolbox or on a wall organizer to prevent loss and collision. For long-term storage, apply a thin coat of rust preventative oil to metal surfaces. - Correct Key Operations
Force Principle: Pull the wrench towards you; do not push it away, to avoid injury if your hand slips.
Stable Stance: Ensure your feet are planted firmly and your body is balanced. Apply controlled, smooth force—avoid sudden jerks or impact
loads.
Direction Check: Before using a ratchet, always confirm the direction selector is set correctly (“lefty-loosey, righty-tighty” is the common rule). Socket Seating: Ensure the socket is fully seated on the nut/bolt head and remains perpendicular to the handle to prevent slippage and damage to the fastener. - Inherent Risk Prevention
Prevent Slipping: Ensure tools and work surfaces are clean and dry. For rusted or corroded fasteners, apply a penetrating oil first—never force it.
Prevent Overload: Stop immediately if you feel unusual resistance. Check if threads are seized, if it’s a left-hand thread, or if a larger/heavier-duty tool is required.
Prevent Ejection: When disassembling components, anticipate the direction parts may fly and take precautions.
Product Overview
- Intended Use
This Impact Socket Set is designed for tightening and loosening various standard bolts, nuts, and screws during routine maintenance, equipment assembly, vehicle upkeep, and home DIY projects.It is also intended for high-torque pre-loading, professional heavy machinery repair, or use as an impact tool. - Intended Users and Environment
Suitable Environment: Indoor or sheltered outdoor areas such as home garages, repair workshops, and DIY workbenches.
Suitable Users: Adult DIY enthusiasts with basic skills, homeowners, vehicle owners, and entry-level maintenance technicians.
Not Suitable: Children may only use specified small tools (e.g., screwdrivers) under strict adult supervision. Unsupervised use is prohibited. - Storage Instructions
Store in the original case or on a customized tool wall panel for easy access and organization.
Avoid prolonged exposure to moisture, high heat (e.g., near radiators), or direct sunlight.
Store tools of different materials (e.g., standard steel vs. chrome-vanadium) separately to prevent mutual damage from knocking
Installation Instructions (Kit Initialization)
This kit is ready-to-use and requires no complex installation. Follow these initialization steps after unboxing:
- Unbox and Verify: Check all components against the product list.
| SN | Model | Qty | Type | Socket List |
| 1 | 69300003 | 29 | 1/2”Metric/SAE | Extension rod: 3, 5, 10 inchSAE deep: 10, 11, 12, 13, 14, 15, 16,17, 18, 19, 20, 21, 22, 23, 24 mmMetric deep: 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1 inch |
| 2 | 69300005 | 50 | 3/8”Metric/SAE | 3” drive impact extension rod, 6” drive impact extension rod, 3/8” universal joint, 1/2” to 3/8” adapter, 3/8” drive ratchet handle, hexagonal handle adapterSAE deep: 5/16, 3/8, 7/16, 1/2, 9/16,5/8, 11/16, 3/4 inchSAE Shallow: 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4 inchMetric deep: 8, 9, 10, 11, 12, 13, 14,15, 16, 17, 18, 19, 21, 22 mmMetric Shallow: 8, 9, 10, 11, 12, 13, 14,15, 16, 17, 18, 19, 21, 22mm |
| 3 | 69300006 | 64 | 3/8”Metric/SAE | 3” drive impact extension rod, 6” drive impact extension rod, 3/8” universal joint, 1/2” to 3/8” adapter, 3/8” drive ratchet handle, hexagonal handle adapterSAE deep: 5/16, 3/8, 7/16, 1/2, 9/16,5/8, 11/16, 3/4, 15/16, 1 inchSAE Shallow: 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 15/16, 1 inch |
| Metric deep: 6, 7, 8, 9, 10, 11, 12, 13,14, 15, 16, 17, 18, 19, 20, 21, 22, 23,24 mmMetric Shallow: 6, 7, 8, 9, 10, 11, 12,13, 14, 15, 16, 17, 18, 19, 20, 21, 22,23, 24 mm | ||||
| 4 | 69300007 | 96 | 3/8”Metric/SAE | spark plug sockets:13/16”, 5/8”,14mm; drive impact extension rods: 3,6 inch; T-bar adapter, 3/8” universal joint, 3/8 “(F) -1/4” (M) adapter, 3/8” drive ratchet handle, hexagonal handle adapter, screwdriver rotation handle, spring sleeve screwdriver head adapter, 40*drill bitsSAE deep: 5/16, 3/8, 7/16, 1/2, 9/16,5/8, 11/16, 3/4 inchSAE Shallow: 5/16, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4 inchMetric deep: 8, 9, 10, 11, 12, 13, 14,15, 16, 17, 18, 19, 21, 22 mmMetric Shallow: 8, 9, 10, 11, 12, 13, 14,15, 16, 17, 18, 19, 21, 22mm |
- Clean: Wipe all tools with a dry cloth to remove any anti-corrosion coating or storage dust.
- Function Test: Test the ratchet’s forward/reverse function for smooth operation. Verify wrench openings correspond accurately to marked sizes.
- Organize: Place small items like sockets into their designated slots in the toolbox in order of size to prevent loss.
- Lubricate: Add 1-2 drops of light machine oil into the ratchet mechanism and work it back and forth a few times to distribute.
Instructions for Use
- General Safety and Operating Procedure
Inspect (tools and conditions) → Select (appropriate impact socket and attachments) → Connect (securely lock all interfaces) → Align (ensure socket is square to the bolt) → Bump Test (short trigger bursts to confirm stability) → Proceed with Work - Core Component: Impact Sockets
Dedicated Use: Must and can only use sockets specifically designed to withstand impact forces. They are made from special alloy steel and heat-treated to have high toughness for absorbing impact energy. The use of regular sockets is strictly forbidden as they pose a risk of shattering and flying fragments.
Size Matching: Select a socket of the correct size (e.g., 17mm, 19mm) and drive size (e.g., 1/2 inch, 3/4 inch) based on the bolt size and workspace.
Installation & Removal: Firmly push the socket’s drive square hole onto the impact wrench’s output shaft (anvil) until it is secured by the locking ball or retainer clip. Press the locking collar on the output shaft to remove. - Attachment Usage Points
Universal Joint (Impact-rated):
- Purpose: Provides a flexible connection in non-linear spaces. Universal joints for impact tools have a more robust internal construction.
- Use: Connect it between the impact wrench and the socket or extension bar. Allows for some angular offset.
- Critical Limitation: Significantly reduces effective torque and is the weakest link in the torque chain. Never use it for high-torque tightening/loosening at high angles (typically >30 degrees). Use only to overcome minor spatial obstacles.
Extension Bar (Impact-rated):
- Purpose: Increases working distance to reach deep or difficult-to-access locations.
- Use: Select extension bars rated for use with impact tools. They can be connected in series, but each added connection point increases torsional vibration and energy loss.
- Note: Excessively long setups can make socket alignment difficult and reduce torque transfer efficiency. Ensure all connections are locked tight. Adapter (Impact-rated, e.g., drive size reducer/increaser):
- Purpose: Converts between different drive sizes (e.g., 1/2″ to 3/8″) to use different socket series.
- Use: Select adapters rated for use with impact tools. Note that after conversion, the torque capacity of the entire system is limited by the weakest link’s rating (usually the smaller drive end).
- Warning: Never use adapters not rated for impact or stack multiple adapters, as this greatly increases the risk of failure.
Drive Ratchet Handle (Manual):
- Purpose: For manually driving sockets when an impact wrench cannot be used or when fine control is needed.
- Use: Insert its square drive into the socket. For manual operation only. Absolutely forbidden to use it with an impact wrench or subject it to impact loads.
- Screwdriver Spinner Handle / Bit Holder Adapter:
- Purpose: Used with hex-shank bits for driving or removing large screws (e.g., self-tapping screws, body bolts).
- Use: Insert the bit into the adapter’s elastic collet or magnetic holder. Ensure the bit type (PH, SL, TX, etc.) perfectly matches the screw head. Note: Apply firm pressure to seat the bit into the screw drive to prevent “cam-out,” which can damage both the screw and the bit.
Documents / Resources
![]() | 69300007 Impact Socket Set |
References
- User Manualmanual.tools
Published: November 4, 2026
