SPV-VERTEL DMR DMR Two Way Radio
Product Information
Specifications:
- Product Name: DMR Two Way Radio
- Model: Smart Pro-Digital
- Manufacturer: Vertel Digital Private
Limited - Address: H-103, Electronics City, Sector-63,
Noida, (U.P.) 201301, India
Product Usage Instructions:
The DMR two way radio model Smart Pro-Digital is designed for
efficient communication over short to medium distances. Follow
these steps to use the product effectively:
Step 1: Power On/Off
Press and hold the power button to turn the device on or
off.
Step 2: Select Channel
Use the channel selector to choose the desired communication
channel.
Step 3: Adjust Volume
Rotate the volume knob to set the audio output at a comfortable
level.
Step 4: Communicate
Press the PTT (Push-To-Talk) button to transmit your message.
Release the button to listen to incoming messages.
Frequently Asked Questions (FAQ):
Q: How do I charge the DMR two way radio?
A: The DMR two way radio can be charged using the provided
charging cable. Connect the cable to the charging port on the
device and plug it into a power source.
Q: Can I use the Smart Pro-Digital model in rugged outdoor
environments?
A: While the Smart Pro-Digital model is durable, it is
recommended to avoid exposing it to extreme weather conditions or
water to ensure longevity.
DMR two way radio
This manual applies to the model, Smart Pro-Digital
Vertel Digital Private Limited H-103, Electronics City, Sector-63, Noida, (U.P.) 201301, India
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. Verification of harmful interference by this equipment to radio or television reception can be determined by turning it off and then on. The user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a different circuit to that of the receiver’s outlet. Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
The device has been tested and complies with SAR limits, users can obtain Canadian information on RF exposure and compliance. Après examen de cematériel aux conformité aux limites DAS et/ou aux limitesd’intensité de champ RF, les utilisateurspeuvent sur l’exposition aux radiofréquences et la conformité and compliance d’acquérir les informations correspondantes.
SAR tests are conducted using standard operating positions accepted by FCC/ISEDC with the device transmitting at its highest certified power level in all tested frequency bands, although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. Before a new model is a available for sale to the public, it must be tested and certified to the FCC/ISEDC that is does not exceed the exposure limit established by the FCC/ISEDC. Tests for each product are performed in positions and locations as required by the FCC/ISEDC.
To control your exposure and ensure compliance with the occupational/controlled environmental exposure limits, always adhere to the following procedures. Guidelines: Do not remove the RF Exposure Label from the device. User awareness instructions should accompany device when transferred to other users. Do not use this device if the operational requirements described herein are not met. Operating Instructions: Transmit no more than the rated duty factor of 50% of the time. To transmit (talk), press the Push-to-Talk (PTT) key. To receive calls, release the PTT key. Transmitting 50% of the time, or less, is important because the radio generates measurable RF energy only when transmitting (in terms of measuring for standards compliance). Keep the radio unit at least 2.5 cm away from the face. Keeping the radio at the proper distance is important as RF exposure decreases with distance from the antenna. The antenna should be kept away from the face and eyes. When worn on the body, always place the radio in an approved holder, holster, case, or body harness or by use of the correct clip for this product. Use of non-approved accessories may result in exposure levels which exceed the FCC’s occupational/controlled environmental RF exposure limits. Use of non-approved antennas, batteries, and accessories causes the radio to exceed the FCC RF exposure guidelines. Contact your local dealer for the product’s optional accessories.
Les tests SAR sont effectués dans des positions de fonctionnement standard acceptées par la FCC/ ISEDC, l’appareil transmettant à son niveau de puissance certifié le plus élevé dans toutes les bandes de fréquences testées. Bien que le SAR soit déterminé au niveau de puissance certifié le plus élevé, le niveau SAR réel de l’appareil pendant son fonctionnement peut être bien inférieur à la valeur maximale. Avant qu’un nouveau modèle ne soit disponible à la vente au public, il doit être testé et certifié par la FCC/ISEDC pour ne pas dépasser la limite d’exposition établie par la FCC/ISEDC. Les tests de chaque produit sont effectués dans des positions et des emplacements tels que requis par la FCC/ ISEDC. Pour un fonctionnement porté sur le corps, cet appareil a été testé et répond aux directives d’exposition RF de la FCC/ISEDC lorsqu’il est utilisé avec un accessoire désigné pour ce produit ou lorsqu’il est utilisé avec un accessoire qui ne contient pas de métal. Pour maintenir la conformité avec les directives d’exposition RF de la FCC/ISEDC, maintenez l’émetteur et l’antenne à au moins 2,5 cm (1 pouce) de votre visage et parlez d’une voix normale, avec l’antenne pointée vers le haut et éloignée du visage. L’équipement est conforme aux limites d’exposition aux rayonnements FCC/ISEDC définies pour l’environnement d’exposition professionnelle/contrôlée. Afin de se conformer aux exigences d’exposition RF FCC/ISEDC, l’installation de l’antenne doit être conforme aux conditions suivantes : Les utilisateurs doivent être pleinement conscients des dangers de l’exposition et être en mesure d’exercer un contrôle sur leur exposition RF pour être admissibles aux limites d’exposition plus élevées. Votre émetteur-récepteur portable sans fil contient un émetteur de faible puissance. Ce produit envoie des signaux de radiofréquence (RF) lorsque le bouton Push-to-Talk (PTT) est enfoncé. L’appareil est autorisé à fonctionner à un facteur de service ne dépassant pas 50 %.
Antenna model: Smart Pro-Digital,The antenna gain is as follows:
Antenna Type
Antenna Gain
Helical
0 dBi
Documents / Resources
 |
VERTEX DIGITAL SPV-VERTEL DMR DMR Two Way Radio [pdf] User Guide SPV-VERTEL DMR, 2BL7PSPV-VERTEL, 2BL7PSPVVERTEL, SPV-VERTEL DMR DMR Two Way Radio, SPV-VERTEL DMR, DMR Two Way Radio, Two Way Radio, Way Radio |