VEKOOTO N92 RV Backup System Wired Kit Camera

VEKOOTO N92 RV Backup System Wired Kit Camera

Thank You!

Thank You for Buying VEKOOTO Product.
Read This User Manual Before Installing and Using It.
Pls keep this instruction or write down our email Vekooto@outlook.com So you can find us once you have any question. You are Always the First for us.

Monitor introduction

The user can perform the manipulation of the guest power segment on the display parameters through the following nuclear health operations.

Monitor introduction

①MODE: Confirm / Select button
②V1V2: Switch channel
③-: Increase button
⑤M: Menu / Return button
④+ : Decrease button
⑥POWER: Turn On/Off button
⑦IR: IR Connector

Remote Controller introduction

  1. Standby: Power ON/OFF
  2. Video Select: Channel switch
  3. Menu: Go in setting page
  4. Mode Select: Turn on / off recording
  5. Function Down: Reduce when in setting page
  6. Function Up: Increase when in setting page
    Note: Button cell model: CR2025 3V

Wiring instructions

Wiring instructions

The wiring method when product use, as follows

  1. Connect Yellow wire to positive power(12-35V).
  2. Connect Red wire to ACC.
    The red wire is connected to the car ignition wire ACC switch (which is the gear switch before starting up the car’s motor), when the car key is turned on, the device will start automatically, and if the vehicle key is turned off, it will automatically turn off.
  3. Connect Black wire to negative power / Ground / Sheet Metal
  4. Connect Blue wire (CH2 trigger) to reversing light.

The wiring method when product test, as follows

  1. Connect Yellow wire and red wire together to the positive power (12-35V).
  2. Connect Black wire to Ground.
  3. Ignore Blue color trigger wires.
  • Before installing it by professional person, please test it if works well, like image display, just in case and save your precious time. Please contact us if you have any question anytime, our email is Vekooto@outlook.com

Note:

  1. Before connecting, you need to confirm that the voltage of the battery is between 12 – 35V.
  2. After connecting the wires, pay attention to the insulation between the power cables to prevent. the power cables from short-circuiting the battery.
  3. The yellow wire must be connected to the ignition wire, otherwise the device will not support the ignition switch.
  4. When you install the 4pin cable, please target every pin to the hole, avoid breaking the pin.

About Trailer installation

If you need to extend the cable for your trailer, please tell us via our email: Vekooto@outlook.com

So we can send the extend cable for you, then you can extend it as the attached picture below shows, and you can disconnect them by Rotating the button of cable. And please tell us how much cable you need and how many feet you need. Email us your Amazon Order ID# :

About Trailer installation

How to install the monitor and camera

① Install the monitor (Ceiling bracket)

Ceiling bracket
How to install the monitor and camera

② Install the monitor brackets
How to install the monitor and camera

③ Install the camera
How to install the monitor and camera

Basic Function

Time Setting Time

Press the Function Icon → button→ Time Setting → Function IconFunction Icon (Increase time/ decrease time)-+ ED (into next time setting)→ Function Icon until last complete set.

  1. Loop Video: 1/3/5/10min
  2. Format: Format the TF card content and system.
Picture
Basic Function

Playback

Press the Function Icon button → Press Function Icon→ Press Function IconFunction Icon twice → Function IconFunction Icon choose AHD1 or AHD2

Basic Function

Split Setting

Press Function Icon button to switch between 4 split modes.

Function

Press the Function Icon bettor→ on Press Function IconFunction Icon Turn On or Off Mirror

Basic Function

MENU FAQ

(1). How to return interface while viewing the Video List?

A. Press the M/V1V2 button, then it can back to the monitor page. At other time, press the Menu button to go back the monitor page.

(4). What is the function of Trigger wire?

A. If you connect the trigger line to the reversing light, the screen will automatically switch to the camera that connected to the reversing light when you reverse. You don't need to manually switch to the camera channel.

(5). How to find the TF card video on the computer?

A: Plug and play. Use a card reader that can read and plug it into your computer.

CUSTOMERS SUPPORT

Email: Vekooto@outlook.com

Logo

Documents / Resources

VEKOOTO N92 RV Backup System Wired Kit Camera [pdf] Installation Guide
N92 RV Backup System Wired Kit Camera, N92, RV Backup System Wired Kit Camera, Backup System Wired Kit Camera, System Wired Kit Camera, Wired Kit Camera, Camera

References

Leave a comment

Your email address will not be published. Required fields are marked *