VAXEE NPWL Wireless Mouse User Guide

NPWL Wireless Mouse
User Guide

Contents hide

1 Contents of Package

2 Mouse Features

3 Motion Sync Adjustment

4 Documents / Resources

4.1 References

5 Related Posts

Contents of Package

Mouse
Wireless Dongle (USB)

Wireless Dongle Adapter
Charging and Data Cable

Setup Wired Mode
Connect the mouse to any USB port on your PC using the charging cable Wireless Moode
Plug the wireless USB dongle into any USB port on your PC.

Mouse Features

Left Button

Right Button
Middle Button

Back Button
Forward Button

DPI Switch Button
Report Rate Button

Click Latency Button
Power Switch

Specifications
DPI Settings: 400 /800 /1600 /3200 dpi
Adjustable USB Report Rate: 125 /500 /1000 |
Adjustable Click Latency: 2/3/4/8ms
Adjustable Competitive
Adjustable Motion Sync:
Made: On / Off
On/ Off
Battery Life: Consistent motion at 1000Hz Up to 100hrs in Standard Made and 55hrs in High Competitive Mode
Charging Speed: From 0%-100% in roughly Thr 50mins
Weight: 73g

	DPI
Sensor: PAVW3AE2S	400 dpi
Connector: USB	800 dpi
Buttons: 9 buttons	1600 dpi
Cable Length: 2 meters (6.6 feet)	3200dpi

Recommended Usage Environment
For optimal wireless performance, use mouse within 20cm of Wireless Dongle and further than 2m from sources of 2.4GHz interference (such as Wi-Fi routers)

Charging and Power LED Lights


Connect the USE cable to use it in wired mode Charging: Both lights blink in a cycle	Fully Charged: Both lights stay on continuously


Both Lights – On Lights return to charging mode in S seconds	Upper Light – On Lights return to charging made in S seconds.


Lower Light – On Lights return to charging mode in S seconds.	Lower Light – Continuous Blinking Lights return to charging mode in 5 seconds.

Lift-off distance Adjustment Hold the Report rate switch button ( ) . A while power is off, fU then turn on the power:


125Hz light blink for 3 times and goes off, mens switch to Low maode (Default).	1000Hz light blink for 3 times and goes off, means switch to High mode.

Motion Sync Adjustment

Hold the DPI switch button ( ) while power is off, then turn on the power:


Dpi light blink in green for 3 times and goes off, means switch the Motion Sync to On.	DPI light blink in blue for 3 times and goes off, means switch the Motion Sync to Off. (Default)

Competitive Mode Adjustment Hold the Click Latency button (8) while power is off. ) While holding, turn the power on.


If the number 4 indicator light blinks 3 times and goes off – Competitive Mode Off.	If the number 2, 4 and 8 indicator lights blink 3 times and go off – Competitive Mode On. (Default)

Displaying Mouse Status Hold the Forward button + Back button + Middle button (3+4+5) ndicator lights on the bottom will show the current status of the mouse. B Dongle Function
NP-01 Wireless provides an A/ B dongle switch function.
If you require an additicnal dongle, please visit the VAXEE website to make your purchase.
For dongle pairing and switching, please scan the QR code below for the “VAXEE Dongle User Manual”.

https://download.vaxee.co

Regulatory
FCC Approval
This device had been tested in accordance with the rocedures and in compliance with Part 15 Subpart B of FCC Rules, and keeps all requirements according to ANSI C63.4 & FCC Part 15 B Regulation and CISPR22 Class B.
FCC15.21:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
15.109:
This device complies with part 15 of the FCC Rules, Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
15.105:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Warning: This device contains transmitters and receivers which emit Radio Frequency (RF) energy.
The device is designed to comply with the limits for exposure to RF energy set by the Federal Communications Commission (FCC) of the United States, Industry Canada (IC) of Canada, and the regulating entities of other countries.