VALBERG VL-ICM20W Ice Cube Maker Instruction Manual

To start making ice, press the button corresponding to the desired size setting.
The ice full indicator light will illuminate when the ice basket is full, and production will stop.

To remove ice, open the lid, lift out the ice basket, and use the ice scoop.
If the water tank is empty, refill it and press the button to restart ice production.

To stop ice production, press the button and unplug the power plug when not in use.

Thank you!

Thank you for choosing this VAL BERG product.
VAL BERG products are chosen, tested, and recommended by ELECTRO DEPOT, so you can be sure you are getting a top-quality, easy-to-use product that won’t let you down.

We’re confident your new device will be a pleasure to use every day!
Welcome to ELECTRO DEPOT.

Product Overview

Parts

A: Ice basket

B: Lid
C: Control panel

1: Small ice cubes indicator light
2: Large ice cubes indicator light

3: Ice full indicator light
4: Add a water indicator light

5: Ice cube size selection button
6: Start/stop button

D: Evaporator
E: Ice shovel

F: Infrared sensors
G: Air vent

H: Power cable with plug
I: Ice scoop
J: Water tank with maximum water level mark – MAX
K: Filter cover with water inlet below
L: Drain hole with plug

Unpack the unit. Remove all the labels from the product except the nameplate. Check that it is complete and in good condition. If the unit is damaged or faulty, do not use it and take it to your retailer or after-sales service centre.
Keep all packaging out of the reach of children and pets. There is a risk of accidents if children or pets play with packaging materials.

Intended use

This unit has been designed to make ice cubes. Do not use it for any other purpose.
Any other use may damage the unit or cause injury.

Specifications

Model: 10003128, VL-ICM20W
Operating voltage: 220-240 V~, 50 Hz, 1 A
Power consumption: 120 W
Water tank capacity (max.): 1.0 L
Daily ice output: 12 kg every 24 hours
Ice storage capacity: 1.0 L / 340 g
Refrigerant: R600a (14 g)

Climate type: N/SN
Off mode power consumption: 0.17 W
The period after which the equipment automatically enters off mode: 10 minutes

Insulation blowing gas: Cyclopentane (C5H10)
Protection class: Class I

Product Usage

Before first use

Clean the unit and its components. ( Cleaning and maintenance).

Use

WARNING!

Before use, make sure that the drain hole plug on the bottom is securely closed.
Make sure that the unit is placed on a dry, level, stable table or surface, away from any heat sources, such as ovens or heaters, to prevent it from malfunctioning.
To ensure good ventilation, leave a gap of approximately 20 cm on all sides of the unit.

Before using the unit for the first time, after transportation or an extended storage period, leave it with the lid open for 2 hours after levelling and positioning the unit on a countertop. This allows the liquids inside the compressor to settle before use. After 2 hours, connect the unit to the power supply.
Do not fill the water tank with hot water. This may damage the unit. Fill the water tank with room temperature water or lower.
Do not use the unit in a very cool environment (less than 5 °C).

Open the lid. Remove the ice basket.
Fill the water tank with drinking water.
Do not fill above the MAX watermark.

Reinsert the ice basket. Close the lid.
Connect the power plug to an appropriate mains socket. The indicator lights will momentarily display.
Then the large ice cube indicator light flashes green. This is the default setting. The unit is now in standby mode.

Press the button to switch the size setting to small ice cubes. The small ice cube indicator light will then turn on and flash green. Similarly, press the button to switch back to the large ice cube setting.
Press the button to start making ice. The selected ice cube indicator light will stop flashing and become solid.
The ice full indicator light lights up red when the ice basket is full. The unit will automatically stop producing ice.
NOTE:
Once the ice has been removed from the ice basket, the unit will automatically restart ice production after approximately 5 seconds.

To remove the ice, open the lid. Lift out and remove the ice basket.
Remove the ice cubes using the ice scoop.
When the water tank is empty, the add water icon lights up red. Open the lid. Remove the ice basket and fill the water tank with water. Reinsert the ice basket and close the lid. Do not fill above the MAX water level mark. When the water tank is full, press the button to restart ice production.

Once you have obtained the desired amount of ice, press the button to stop ice production.
Unplug the power plug from the mains socket.

NOTES

You can stop the ice production process at any time by pressing the button.

Only use drinking water.
The first three cycles of ice production may have smaller and irregularly shaped ice cubes.
When the ambient temperature is around 25°C, ice can remain solid inside the unit for up to 1.5 hours.

If the compressor does not work due to a lack of water, a full ice tray, or a power outage, the unit will pause for three minutes before restarting.

Cleaning and maintenance

WARNING!

For hygiene reasons, the unit must be cleaned before and after each use.

Do not use organic solvents, boiling water, cleaners, strong acids or alkalis, etc., to clean the unit.
Do not clean the evaporator.
Before cleaning or maintaining the unit, make sure that it has been switched off and unplugged from the mains socket. Let it cool completely and remove any ice cubes.

Never immerse the unit, power cord, or plug in water or any other liquid.
Clean the unit (inside and outside) with a soft, slightly damp cloth.
Drain the water tank and refill with fresh water every 24 hours to ensure the quality of the ice cubes.

After use, leave the lid open to prevent mould and bacteria growth.

Draining water from the water tank:

Move the unit forward until it hangs at least 10 cm off the edge of the countertop and over the edge of a sink or container to collect the water. Remove the drain plug on the bottom of the unit to release the water.

Tilt the appliance up to 30° to assist the draining. If there is residual water in the ice-making area, gently push the ice shovel backwards so that all the water drains into the water tank.
After draining, insert the drain plug into the drain plug hole.

Cleaning the internal parts and flushing the pipes

Fill the water tank to the MAX water level mark with water. If there is a buildup of scale, you can use a solution of 50% water and 50% white vinegar.
Press and hold the button to start cleaning. The four indicator lights flash alternately, and the pump starts to pump water around the appliance. The cleaning program takes 5 minutes.
To stop the cleaning mode at any time, press the button.

When the cleaning program has finished or it has been stopped, the unit will enter the standby mode (the selected green ice cube indicator light flashes). Drain the water from the water tank.

Cleaning the filter cover:

Remove the ice basket.

Take out the filter cover.
Clean with clean water and a soft brush (such as a toothbrush).
Reinsert the filter cover.

Troubleshooting

Problem	Possible Cause	Solution
The indicator is lit.	• Low water level or no water. • The water inlet under the filter cover is blocked, or there is air in the system.	• Stop ice production. Fill with water. Press to restart ice production. • If the unit still does not work, take it to the nearest service centre.
The indicator is lit.	• The ice basket is full. One or both infrared sensors are blocked by ice. • The infrared sensors are not working.	• Remove the ice from the ice basket. • Clean and remove any foreign objects from the infrared sensors. Restart the unit.

Problem	Possible Cause	Solution
The,, and indicators are lit up simultaneously.	• The ice basket is not in the correct position. • There is ice under the ice shovel, jamming it. • The motor is damaged.	• Unplug the unit and take out the ice basket, then plug it back in again. Restart the unit. • Disconnect the power cable from the mains socket. Gently push the ice shovel to the rear of the unit and remove the ice chips or allow them to melt before restarting the unit. After 3 minutes, the unit will restart. • Take the unit to the nearest service centre.
The unit is turned on, but no indicator lights display.	• Blown fuse.	• Replace the fuse and restart the unit.
The ice cubes are stuck.	• It is taking too long to make ice. • The water in the water tank is too cold. • There is too much ice in the ice tray.	• Stop ice production. Restart the unit once the ice has melted. • Fill the water tank with water at a temperature between 8°C and 25°C. • Remove the ice from the ice basket.
Ice production appears normal, but no ice is being produced.	• The ambient temperature or water temperature is too high. • The compressor has no refrigerant, is damaged, or the fan motor is damaged.	• Start ice production in an environment with an ambient temperature below 32°C. Fill the water tank with fresh water. • Take the unit to the nearest service centre.
Low ice production.	• Low heat dissipation. • The water temperature is too high. • The ambient temperature is too high.	• Check there is sufficient ventilation around the unit (min. 20 cm on all sides). • Fill the water tank with water at a temperature between 8°C and 25°C. • Use the unit in an environment with an ambient temperature below 32°C.

Storage

Always unplug the unit before storing it.
Store the unit in a fresh, dry and dust-free place, out of the reach of children and pets.

Please retain the packaging and use it to store your unit when it is not in use for an extended period of time.

WARRANTY CONDITIONS

This product is guaranteed against faults caused by defects in manufacturing or the materials used for a period of two years, starting from the date of purchase.
This warranty does not cover defects or damage caused by failure to install the device correctly, incorrect use of the product, or excessive wear and tear. *Proof of purchase required.

FAQ

Q: How often should I clean the appliance?
- A: It is recommended to clean the appliance every few weeks to maintain optimal performance.
Q: What should I do if the ice production stops suddenly?
- A: Check if the water tank is filled to the appropriate level and restart ice production as instructed.

Documents / Resources

VALBERG VL-ICM20W Ice Cube Maker [pdf] Instruction Manual
VL-ICM20W, VL-ICM20W Ice Cube Maker, Ice Cube Maker, Cube Maker, Maker

References

User Manual

VALBERG VL-ICM20W Ice Cube Maker

Product Using Instructions