Fikstur sensori uchun Keilton Basic RM51 masofadan boshqarish pulti

Tavsif

The RM51 Remote is used to program the configurations of the Keilton Basic sensors using infrared (IR) communications with the devices. It offers 6 default modes of configurations plus manual settings. Customer configurations can be created, saved, and then sent to each device, ensuring a rapid deployment.

Xususiyatlari

• Kam quvvat sarfi.
• Infrared communication.
• Setting most of the Keilton Sensors G2.
• Custom Configurations can be saved to A, B, C, D, or For.
• 40′ maximum IR range.
• RML (included with new orders, available as an accessory for order), installed, will increase the IR range. (See table below)

Texnik xususiyatlari

Buyurtma haqida ma'lumot

Model	Tavsif
RM51.A0	Basic Sensor Controller RM51
RM51.A1	Basic Sensor Controller RM51 With RML

Buyurtma haqida ma'lumot - Aksessuarlar

Model	Tavsif
RML	Extended IR range for commissioning

O'lchamlari

Mahsulot yorlig'i

Masofaviy ko'rsatmalar

Xotira rejimi (ishga tushirish)
To begin commissioning, follow these steps:

1. Xotira pro-ni tanlangfile: A, B, C, D yoki E.
2. The remote’s indicator lights will flash, indicating the currently saved settings.
3. Settings can be configured by pressing the appropriate buttons in the highlighted gray area of the remote (TRIM-LEVEL, SENSITIVITY, HOLD TIME, STANDBY DIM, STANDBY TIME, and PHOTOCELL). Review the selected settings and make changes as needed.
4. Point the remote at the desired luminaire and press “SEND.”
5. The luminaire will flash twice to confirm that he settings are saved. Changing a parameter in a memory profile will automatically override previous settings.
6. If configuring multiple luminaires, repeat steps 4 and 5 after selecting the configured memory mode.

E Mode allows for visual adjustment to choose the desired dimming level.

Kunduzgi hosilni yig'ish (F rejimi)
Continuous Adjustment Mode adjusts dimming levels based on daylight.

1. Point the remote at the desired luminaire and press “ON,” then press DIM+ or DIM- to adjust the dimming level.
2. Press “F.” The indicator lights on the remote will show the current saved settings. Note: Only TRIM-LEVEL, SENSITIVITY, and HOLD TIME can be selected for Daylight Harvesting settings
3. Review the selected settings and make changes as necessary. Press “SEND.”
4. If the configuration is successful, the luminaire will flash twice to confirm that the setting is saved. If configuring multiple luminaires, select the configured Daylight Harvesting settings, then follow steps 1, 2, and 3.

Qo'shimcha masofaviy funktsiyalar

ON	Burilishlar ON yoritgichlar.
O'CHIRIB	Burilishlar O'CHIRIB yoritgichlar.
TEST	The fixture enters the test mode and exits automatically after 5 minutes. The test mode parameters are configured as follows: Trim-level: 100%, Sezuvchanlik: YUQORI, Kutish vaqti: 2s, Standby dim: 50%, Kutish vaqti: 2s.
RESET	Trim= 100%, Sensitivity = Yuqori, T1 = 5 min, Standby Dim = 30%, T2 = 60 min, Photocell = O'CHIRIB.
DIM+/-	Press Dim+ or Dim- to adjust brightness in 0.5V increments. Hold the button for continuous xira
TRIM-DARAJA	Set the Maximum brightness.
Sezuvchanlik	Set the motion sensitivity of the sensor PAST:50% / YUQORI:100%, O'chirish: disable the motion detection function.
TUTISH VAQT	Kutish rejimiga oʻtishdan oldin bandlikni aniqlamasdan oʻtadigan vaqt.
KUTISH XARATLI	Select any standby dim level.
KUTING TIME	Standby time, when the time is set to “∞”, the daylight detection function is activated.
FOTOSEL	visible light threshold, the fixture is allowed to be turned on when it falls below the threshold PAST:5fc / YUQORI:20fc, KAL: Collect the current visible light illuminance as the threshold, O'chirish: disable PHOTOCELL function.
REJIM	Default configuration parameters for modes A uchun F.
YUBORISH	Sozlamalarni sensorga yuboring.
SUVAT Rejim A	Trim= 100%, Sensitivity = Past, T1 = 30 min, Standby Dim = 50%, T2 = ∞, Photocell = KAL.
SUVGA REJIM B	Trim= 100%, Sensitivity = Past, T1 = 30 min, Standby Dim = 50%, T2 = 15 min, Photocell = KAL.
SUVGA REJIM C	Trim= 100%, Sensitivity = Past, T1 = 30 min, Standby Dim = 50%, T2 = 15 min, Photocell = O'CHIRIB.
SUVGA REJIM D	Trim= 50%, Sensitivity = Past, T1 = 30 s, Standby Dim = 50%, T2 = 30 min, Photocell = KAL.
SUVGA REJIM E	Manual Dimmer Mode, Trim 100%.
SUVGA REJIM F	Daylight Harvesting, Trim= 50%, Sensitivity = Past, T1 = 15 min.

Biz bilan bog'lanish

• 7001 Columbia Gateway Drive, Suite 210, Columbia, MD 21046, USA
• T: +1 443-320-2233 (M-F 9 am-5 pm ET)
• E: support@autani.com

Tez-tez so'raladigan savollar

How do I change the memory profile sozlamalar?

Select the desired memory profile on the remote and adjust settings as needed before pressing SEND to save

Can I configure Daylight Harvesting settings for multiple luminaires simultaneously?

No, you need to configure Daylight Harvesting settings for each luminaire individually using the F Mode on the remote.

What is the expected operation if the user sets Standby Time to something other than INFINITE?

moiton -> the intensity of ambient light is lower than the threshold set by the PC->turn on the light and dim to trim-level->t1 timeout->dim to standby dim ->t2 timeout->turn off the light.

If it does not turn OFF the fixture, why would Mode B and D use CAL as the default?

The ambient light intensity stored by CAL will serve as the threshold for turning on the lights, but it has no connection with the function of turning off the lights.

Hujjatlar / manbalar

Fikstur sensori uchun Keilton Basic RM51 masofadan boshqarish pulti [pdf] Foydalanuvchi qo'llanmasi Armatura sensori uchun RM51.A0, RM51.A1, RM51 masofadan boshqarish pulti, RM51, armatura sensori uchun masofadan boshqarish pulti, armatura sensori uchun, armatura sensori

Ma'lumotnomalar

• Foydalanuvchi uchun qo'llanma