STM32CubeProgrammer dasturi
Mahsulot haqida ma'lumot
Foydalanuvchi qo'llanmasida ko'rsatilgan mahsulot STM32CubeProgrammer hisoblanadi. Bu STM32 mikrokontrolörlarini dasturlash uchun STMicroelectronics tomonidan ishlab chiqilgan dasturiy vositadir. STM32CubeProgrammer STM32 qurilmalarini dasturlash va disk raskadrovka qilish uchun qulay interfeysni taqdim etadi va J kabi turli dasturlash usullarini qo'llab-quvvatlaydi.TAG, SWD va UART.
Dasturiy ta'minotni rasmiy STMicroelectronics'dan yuklab olish mumkin webquyidagi havoladan foydalangan holda sayt: https://www.st.com/en/development-tools/stm32cubeprog.html
Mahsulotdan foydalanish bo'yicha ko'rsatmalar
- STM32CubeProgrammer dasturini quyidagi havola orqali yuklab oling: https://www.st.com/en/development-tools/stm32cubeprog.html
- Kerakli yangilanish bilan USB flesh-diskini tayyorlang files. Yangilanganligiga ishonch hosil qiling files STM32CubeProgrammer bilan mos keladi.
- Qurilmaning o'ng tomonidagi qayta ishga tushirish tugmachasini toping.
- Boot0 tugmasini ushlab turganda qayta ishga tushirish tugmachasini bosing. Bu qurilmani yuklash rejimiga o'tkazadi.
- Kompyuteringizda STM32CubeProgrammer dasturini ishga tushiring.
- Yangilanishni o'z ichiga olgan USB flesh-diskini ulang files qurilmaning o'ng tomonidagi pastki USB portiga o'tkazing.
- Yangilash jarayoni tugashini kuting. Tugatgandan so'ng, qurilma avtomatik ravishda qayta ishga tushadi.
Iltimos, STM32CubeProgrammer dasturi yordamida STM32 mikrokontrollerlarini muvaffaqiyatli dasturlash va yangilashni ta'minlash uchun berilgan ko'rsatmalarga diqqat bilan rioya qilish muhimligini unutmang.
- STM32CubeProgrammerni yuklab oling https://www.st.com/en/development-tools/stm32cubeprog.html
- Yangilangan USB flesh-diskini tayyorlang files
- Boot0 tugmasini ushlab turganda o'ng tarafdagi qayta ishga tushirish tugmachasini bosing
- STM32CubeProgrammerni ishga tushiring
- Tayyorlangan USB xotira kartasini qurilmaning o'ng tomonidagi pastki USB portiga ulang. Yangilash tugallangandan so'ng, qurilma avtomatik ravishda qayta ishga tushadi
1. STM32CubeProgrammer dasturini yuklab oling https://www.st.com/en/development-tools/stm32cubeprog.html
2. Yangilangan USB flesh-diskini tayyorlang files
3. Boot0 tugmasini ushlab turganda o‘ng tarafdagi qayta ishga tushirish tugmachasini bosing. 4. STM32CubeProgrammerni ishga tushiring.
5. Tayyorlangan USB xotira kartasini qurilmaning o'ng tomonidagi pastki USB portiga ulang. Yangilash tugallangandan so'ng, qurilma avtomatik ravishda qayta ishga tushadi
Hujjatlar / manbalar
 |
ST STM32CubeProgrammer dasturi [pdf] Foydalanuvchi qo‘llanmasi MBT-SI09, STM32CubeProgrammer dasturiy ta'minoti, STM32CubeProgrammer, dasturiy ta'minot |