XtremepowerUS MIG-195 گیس-کم فلوکس کور ویلڈر ہدایت نامہ

1. اہم حفاظتی معلومات

Read and understand all safety warnings and instructions before operating this welding machine. Failure to follow these instructions may result in electric shock, fire, serious injury, or death.

• الیکٹرک شاک مار سکتا ہے: لائیو برقی حصوں کو مت چھونا۔ خشک ویلڈنگ کے دستانے اور حفاظتی لباس پہنیں۔ اپنے آپ کو کام اور زمین سے الگ رکھیں۔
• Fumes and Gases Can Be Hazardous: Keep your head out of the fumes. Use ventilation or exhaust to remove fumes from the breathing zone.
• آرک شعاعیں آنکھوں اور جلد کو جلا سکتی ہیں: ایک مناسب شیڈ فلٹر کے ساتھ ویلڈنگ ہیلمیٹ پہنیں۔ جلد کی حفاظت کے لیے حفاظتی لباس پہنیں۔
• آگ اور دھماکے کا خطرہ: Remove all flammable materials from the welding area. Have a fire extinguisher nearby.
• گرم حصے شدید جلنے کا سبب بن سکتے ہیں: Allow welded materials to cool before handling.
• مقناطیسی میدان: پیس میکر پہننے والوں کو آپریشن سے پہلے اپنے ڈاکٹر سے مشورہ کرنا چاہیے۔
• گرنے والی اشیاء: Secure workpieces before welding.
• شور: سماعت کا تحفظ پہنیں۔

Always ensure proper grounding and use appropriate personal protective equipment (PPE) including welding helmet, gloves, and protective clothing.

2. پروڈکٹ ختمview

The XtremepowerUS MIG-195 is a gas-less flux core wire welding machine designed for welding normal thin steel and iron. It features automatic wire feed and operates on 220V power. This compact welder is suitable for home DIY projects and general repair work.

Figure 1: XtremepowerUS MIG-195 Gas-Less Flux Core Welder with included welding mask, ground clamp, and torch.

3. سیٹ اپ ہدایات

3.1 پیک کھولنا اور معائنہ کرنا

1. پیکیجنگ سے تمام اجزاء کو احتیاط سے ہٹا دیں۔
2. Inspect the welder and all accessories for any signs of damage during shipping. If any damage is found, do not operate the machine and contact customer support.
3. Ensure all included components are present: MIG 195 Welder, Torch, Ground Cord, Chipping Hammer/Wire Brush, Tip, Welding Mask.

3.2 پاور کنکشن

This welder requires a 220V power supply. Ensure your electrical outlet matches this requirement. The unit comes with a power plug that may require wiring to a suitable 220V receptacle. Consult a qualified electrician if unsure about wiring.

Figure 2: Included power plug components. This welder operates on 220V. Consult a qualified electrician if unsure about wiring.

3.3 وائر سپول کی تنصیب

The MIG-195 is designed for gas-less flux core welding. Use appropriate flux core wire for your application.

1. وائر فیڈ میکانزم تک رسائی کے لیے ویلڈر کے سائیڈ پینل کو کھولیں۔
2. Place the wire spool onto the spool holder. Ensure the wire unwinds smoothly from the bottom of the spool towards the wire feed rollers.
3. Thread the wire through the guide tube and into the wire feed rollers.
4. Close the wire feed roller tension arm and adjust the tension. The tension should be firm enough to feed the wire without slipping, but not so tight that it deforms the wire.
5. Feed the wire through the torch liner until it exits the contact tip. You may need to press the trigger on the welding torch to activate the wire feed motor.

شکل 3: اندرونی view of the welder, illustrating the wire feed mechanism and spool holder for flux core wire.

Figure 4: A spool of flux core welding wire, suitable for use with the MIG-195 welder.

3.4 Polarity Setting

For gas-less flux core welding, the polarity is typically DC electrode negative (DCEN), meaning the welding torch is connected to the negative terminal (-) and the ground clamp to the positive terminal (+). Verify the correct polarity for your specific flux core wire type.

3.5 گراؤنڈ کلamp کنکشن

زمین سے جڑیں clamp to the workpiece. Ensure a clean, bare metal connection for optimal electrical conductivity. A poor ground connection can lead to unstable arcs and poor weld quality.

Figure 5: The welding torch and ground clamp, essential components for the welding process.

4. آپریٹنگ ہدایات

4.1 کنٹرول اوورview

شکل 6: تفصیلی view of the control panel, showing power switches, voltage/amperage selectors, and wire feed speed dial.

• آن/آف سوئچ: یونٹ کو آن یا آف کرتا ہے۔
• والیومtage/Amperage Selector (1/2, MIN/MAX): Adjusts the welding power output. Use '1' for lower power and '2' for higher power. Within each setting, 'MIN' and 'MAX' provide fine-tuning.
• Wire Feed Speed Dial (0-10): Controls the speed at which the welding wire is fed through the torch. Higher numbers indicate faster wire feed.
• Thermal Overload Indicator: A light that illuminates if the machine overheats, indicating the need for a cool-down period.

4.2 ویلڈنگ کا عمل

1. ورک پیس تیار کریں: Ensure the workpiece is clean, free of rust, paint, and grease.
2. پیرامیٹرز سیٹ کریں: Refer to the welding setup guide (often located inside the welder's cover) or a welding chart for recommended voltage and wire feed speed settings based on material thickness and wire diameter.
3. پی پی ای پہنیں: Always wear your welding helmet, gloves, and protective clothing.
4. ویلڈنگ شروع کریں: Position the torch tip approximately 1/4 to 3/8 inch from the workpiece. Press the trigger to start the wire feed and initiate the arc.
5. Maintain Arc: Move the torch steadily along the joint, maintaining a consistent arc length and travel speed. Observe the weld puddle and adjust your technique as needed.
6. Finish Weld: Release the trigger to stop the arc and wire feed. Allow the weld to cool before chipping away the slag (from flux core).

4.3 ڈیوٹی سائیکل

The duty cycle indicates how long a welding machine can operate continuously within a 10-minute period before needing to cool down. Exceeding the duty cycle can damage the machine.

• 10٪ 180 میں AMP
• 60٪ 74 میں AMP
• 100٪ 60 میں AMP

سابق کے لیےample, at 180 AMP, the machine can weld for 1 minute out of every 10 minutes. If the thermal overload indicator lights up, stop welding and allow the machine to cool down.

4.4 Wire Capacity

• Flux Core: 0.047" (1.2mm), 0.023" to 0.035" (0.6-0.8mm)
• Steel & Stainless Steel (Solid Wire, requires gas): 0.031" (0.8mm)
• Aluminum (Solid Wire, requires gas): 0.030" to 0.039" (1.0mm)

Note: This model is primarily advertised as "Gas-Less" for flux core welding. Using solid wire for steel or aluminum would require an external gas supply and regulator, which are not included with this specific "Gas-Less" model.

5 دیکھ بھال

باقاعدگی سے دیکھ بھال آپ کی ویلڈنگ مشین کی لمبی عمر اور محفوظ آپریشن کو یقینی بناتی ہے۔

• باقاعدگی سے صاف کریں: Use compressed air to blow out dust and debris from the machine's vents and internal components. Do this periodically, especially in dusty environments.
• کیبلز اور کنکشن کا معائنہ کریں: Check all cables (power, ground, torch) for cuts, fraying, or loose connections. Replace damaged cables immediately.
• Torch Maintenance:
  • Clean the contact tip and nozzle regularly to remove spatter.
  • Replace worn contact tips and nozzles as needed.
  • Ensure the torch liner is free of kinks and blockages for smooth wire feeding.
• وائر فیڈ میکانزم: Keep the wire feed rollers clean. Check for proper tension and alignment.
• گراؤنڈ کل۔amp: گراؤنڈ cl کو یقینی بنائیںamp is clean and makes good contact with the workpiece.

Figure 7: Common spare parts for the welder, such as fuses, contact tips, washers, and circlips, which may require periodic replacement.

Figure 8: Included welding mask and chipping hammer with wire brush, useful for post-weld cleaning and protection.

6 خرابیوں کا سراغ لگانا

یہ سیکشن عام مسائل کو حل کرتا ہے جن کا آپ کو آپریشن کے دوران سامنا ہو سکتا ہے۔

7. وضاحتیں

8. وارنٹی اور سپورٹ

For warranty information, technical support, or to order replacement parts, please contact XtremepowerUS customer service. Refer to the contact information provided with your product packaging or visit the official XtremepowerUS webسائٹ

When contacting support, please have your model number (MIG-195) and part number (55016) available.