UNTITLED SWS Series Wind and Solar Hybrid Controller
Important Safety Warning
Before using the controller, please read all instructions and cautionary markings on the unit and this manual. Store the manual where it can easily be accessed.
This manual includes all safety warnings, installation, and operation guidance of the SWS series wind & solar hybrid controllers.
- Before installing and using this controller. Read all instructions and cautionary markings on the controller and all appropriate sections of this guide.
- Do not use the machine in the place where has flammability and explosive gas/articles. Beware of flames and sparks.
- Please contact our after-sales person if the machine doesn’t work.
- Do not change the electrical components and parts yourself, or we will not be responsible for the warranty items and related duties.
- Please install the machine indoors to avoid rainwater from entering the controller.
- Please keep good ventilation and heat dissipation.
- Please install a circuit breaker outside the controller if conditions allow.
- Please use copper cable for the line connection, and choose the right diameter of cable according to the actual current.
- To avoid a risk of fire and electric shock, make sure the existing wiring is in good condition and that the wire is connected tightly.
- Do not restart the controller immediately when it alarms. Please analyze the fault reasons and repair them first.
Basic Information
Introduction and Features
- SWS is a kind of MPPT wind &solar hybrid controller. It can control the wind turbine generation and solar generation to charge the battery in an efficient and safe way.
Features
- Wind&Solar hybrid controller of high quality.
- LCD Display. Easy setup.
- Complete protection functions.
- RS232/RS485/RJ45/GPRS/ WiFi /Bluetooth Optional (For those with GPRS/WiFi/Bluetooth/RJ45 can also be monitored through App.)
Product Installation
Installation Notes
- The machine should be kept indoors and well ventilated.
- Environment temperature: -20~+40°C; Humidity: <=95%, no condensing
- Altitude should not be more than 40000m (when the altitude is more than 1000m, the machine should be used according to the GB/T3859.2 regulations)
- Avoid using the machine in direct sunlight, sun exposure, rain, humidity, acidic food, and dust.
- To guarantee the lifespan, it is suggested that the space around the device has no other items within 30 cm.
- The machine can only charge the battery in the rated voltage range.
- The machine can only be connected to the wind turbine and PV with the allowed power and voltage.
Installation and Wiring
Installation Steps
- Please refer to the specific installation situation. Generally speaking, if it is used in a street light pole, you can fix the controller to the rail inside the light pole.
- If it is installed in the power box, the power box is drilled according to the hole size, and the controller is fixed with M4 screw.
Electrical Connection
Please connect those parts according to the order of (1)-(4), and notice the following items.
- Connect the load positive and negative terminal to the “DC OUTPUT terminals < as”+”-1′”-2″ relatively. 2 output loads share the same “+” terminal.
- Connect the battery bank to the controller by the terminal which marks “BATTERY”. (do not reverse the connection of positive and negative terminals)
- When the wind turbine is still or running at a low speed, connect its output cable to the “WIND INPUT’ terminal on the controller.
- Connected the terminals of solar panels to “SOLAR INPUT” terminals +””-“on the controller;
- Check all the connections to make sure they are connected correctly and tightly.
Operation Interface Introduction
LCD Display
- After the power is connected, the whole screen is in a browsing state.
- It shows battery voltage, and can be changed to the following information by pressing the relevant buttons.
LCD Information Define
Load Output Modes
- 7 load output modes are optional, and can be set on the LCD display or software on the computer.
Parameters Setting
When you need to adjust specific parameters, please follow the steps below:
- Press
to browse the interface. And then press ” Enter ” to enter the setting interface. (LCD shows “SET) - Press to adjust the parameter values.
- Press” Enter” to save the setting and back to the browsing status. Or press “Esc” to cancel the adjustment and back to the browsing status.
See the following table for specific parameter settings
Trouble Shooting
Technical Parameters
Warranty
- The product shall be in warranty for one year from production.
- Please take the contract as the final one if it has special terms on warranty.
Documents / Resources
 |
UNTITLED SWS Series Wind and Solar Hybrid Controller [pdf] User Manual WWS06, 24, SWS Series Wind and Solar Hybrid Controller, SWS Series, Wind and Solar Hybrid Controller, Solar Hybrid Controller, Hybrid Controller |