UNICOM Engineering E-1800 R7 High-Reliability Medium Density Enterprise Computing Systems
Unit Disassembly for WEEE
| Revision | Date | MR # | Revised By | Description of Changes |
| 01 | 06/29/2023 | 37592 | John Loos | Draft |
| 0A | 11/28/2023 | 37592 | John Loos | Released |
NOTE: Disconnect any AC Power Cords or shut off any DC power source attached to the power supplies and then remove any wires connected to the DC power supplies before disassembly of the unit.
PRODUCT DISASSEMBLY INSTRUCTIONS
Most parts can be removed easily by hand. In some cases, common household tools such as Philips and/or flat-head screwdrivers may be necessary. Some components may require needle-nose pliers. Instructions for removing parts in this product can be found in the Intel System Integration and Service Guide documentation. All removed components should be disposed of in the appropriate recycling bin. The most recent documentation for this server can be found online at:
Revision 1.2 is attached here for reference:
- Intel_Server_System_M50FCP1UR_TPS_Re
Images shown are representative of the product and may vary depending on the actual configuration.
Example: 12-drive, E-1800 R7 Server with lid:]
Example: E-2900 R7 Internal View
| Recycling/Material Code | Important Information |
| Material /Components, which must be removed and treated separately | |
| Lithium Battery | Battery-free of hazardous substances, installed in the socket on the motherboard |
| Printed circuit boards | Motherboard, DIMMs, PCI card, PCI riser, Power Supply, and DVD adapter PCB |
| Disk Drives | Hard Drive, DVD Drive, Solid State Drive |
| Material /Components, which can disturb certain recycling processes | |
| Aluminum | Heat sink, handles |
| Material /Components, through which benefits can normally be achieved | |
| Cold Rolled Steel | Top cover, chassis bottom, and rails |
| * ABS | Pushbuttons, Shroud |
| Cables | Distributed in device |
| Fans | |
| Special notes | |
| * Flame retardant of plastics does not contain PBB and PBDE. | |
Annex A
| Producer: | <Company name, other on addressing the producer> |
| Scope of information sheet: | < Product category as in Annex IA of WEEE Directive, or type of equipment as in Annex 1B of WEEE Directive, or producer’s Product Family, or
single products identified by brand and model name > |
| Component or Material | Remarks / Location |
| Battery (internal *) containing Mercury (Hg)/ NiCad/Lithium/ Other | Lithium battery
Located on the motherboard |
| Backlighting lamps of LCD/TFT or similar screens containing Mercury (Hg) | NONE |
| Mercury (Hg) in other applications** | NONE |
| Cadmium** | NONE |
| Gas discharge lamps | NONE |
| Plastic containing ruminated flame retardants other than in Printed Circuit Assemblies *** | NONE |
| Component or Material | Remarks / Location |
| Liquid Crystal Displays with a surface greater than 100 cm2 | NONE |
| Capacitors with PCB’s | NONE |
| Capacitors with substances of concern**** + height > 25 mm, diameter > 25 mm or proportionately similar volume | NONE |
| Asbestos | NONE |
| Refractory ceramic fibers | NONE |
| Radio-active substances | NONE |
| Beryllium Oxide | NONE |
| Other forms of Beryllium | BE-CU in some connector contacts |
| Gasses – which fall under Regulation (EC) 2037/2000 and all hydrocarbons (HC). | NONE |
| Components with pressurized gas which need special attention (Pressure > 1,5 bar) ***** | NONE |
| Liquids ***** if volume > 10 cl (or equivalence in weight, e.g. for PCB, oil…) | NONE |
| Mechanical components that store mechanical energy (i.e. springs) or equivalent parts that need special attention *****
(diameter > 10 mm and height > 25 mm or proportionally similar volume and expanding) |
NONE |
| PBDE (deca- & octa-BDE) and Perfluorocatane sulfantes (PFOS) in Directive 2006/122/EC | NONE |
- = Arrow indicates the need for the location of the compartment/ substances within the product. When the location of a substance/component is requested, it is at the part level, e.g. main board, housing, etc
- Internal means that batteries can only be removed by opening the product using (a) tool(s).
- Substances are considered to be in the product if present above the levels specified in Commission Decision 2011/65/EU (RoHS Directive) or if their use is permitted through exemptions in Annex III of this directive.
- To be coherent with the industry’s current standards and practices on tracking of plastic parts, the Directive 2002/96 (EC) Annex II requirement is understood to focus on plastic parts that weigh more than 25 g.
- The substance of concern other than PCB, to be specified/ addressed further in the context of Directive 2002/96 (EC) Annex II national requirements and European developments
- Needs of an equivalent nature as those for maintenance, service manuals, and installation for safety purposes.
Specifications
- Product Name: E-1800 R7 Unit
- Document Number / Disk File: 597-2001-00
- Assemblies Covered: E-1800 R7 (786-7327-00)
FAQ
Q: What tools are recommended for disassembling the E-1800 R7 Unit?
A: Common household tools such as Philips and flat-head screwdrivers, as well as needle-nose pliers, may be required for disassembly.
Q: Where can I find the most recent documentation for this server?
A: The latest documentation can be accessed online at the provided Intel website link.
Q: How should I dispose of removed components?
A: All removed components should be disposed of in the appropriate recycling bin following electronic waste disposal guidelines.
Documents / Resources
 |
UNICOM Engineering E-1800 R7 High Reliability Medium Density Enterprise Computing Systems [pdf] Instructions E-1800 R7, E-1800 R7 High Reliability Medium Density Enterprise Computing Systems, High Reliability Medium Density Enterprise Computing Systems, Reliability Medium Density Enterprise Computing Systems, Medium Density Enterprise Computing Systems, Density Enterprise Computing Systems, Enterprise Computing Systems, Computing Systems, Systems |
