PSU1 Series Direct Fixing Projector
“
Product Information
Specifications
- Product Models: PSU1, PSU2, PSC, PPSU, VSU
- Maximum Weight Capacity: 40-70kg
Product Components
| Description | Quantity |
|---|---|
| PSU1 – Socket & Bar Assembly | – |
| PSU1/2 – Dedicated Fixing Plate (Example) | – |
Product Usage Instructions
Tools Required
- 4mm & 5mm Allen Keys
- 13mm Spanner
- 17mm Spanner
Installers Required
1-2 installers are recommended for the installation process.
Installation Steps
Step 1 (All Models)
Loosen the hex screws to disconnect the upper and lower parts of
the mount. Attach the upper part to the ceiling plate or wall arm
and fix the lower part to the projector.
Step PSU2 1/2
Use the fixing screws to attach the lower part of the PSU to the
inverted projector.
Step PSC
Rest the projector on its feet in the base of the cradle
designed for your specific projector.
Step 2 (All Models)
Align the socket with the column or peg, thread cables through,
and tighten the throughbolt and grub screws. Hook the projector
over the screws and adjust tilt angles.
Use safety throughbolts to secure the PSU and be cautious of
cable stretching when adjusting angles.
Frequently Asked Questions (FAQ)
Q: How do I know which dedicated fixing plate or projector
cradle to use?
A: The dedicated fixing plate or cradle is designed specifically
for the projector model you have ordered, ensuring compatibility
and proper fit.
“`
01865 767676 sales@unicol.com www.unicol.com
PSU1 / PSU2 / PSC / PPSU / VSU
Guide Max. Weight: 40-70kg *Please check model specific details before installing*
Revised 13/08/24
WARNING
Please carefully inspect the product before assembling. If you notice any apparent damage, call your carrier claims agent and do not continue the installation until it has been reviewed. Please watch for pinch points. Do not put your fingers between moveable parts. Do not tamper with or disassemble any spring loaded parts. Before installing, make sure that the supporting surface will support five times the combined load of the solution and the hardware. Never exceed the maximum load capacity. Please also layout all components to ensure that you have all of the required parts before proceeding (see BOM list on following page). Use of this product for anything other than its specified use may result in failure or personal injury. This product is intended for indoor use only. We recommend using a qualified trades person for installation. Use an assistant or lifting equipment to lift and position products.
For support, please call: +44 (0)1865 767676 or email: sales@unicol.com
01865 767676 sales@unicol.com www.unicol.com
#
TOOLS REQUIRED
1 4mm & 5mm Allen Keys
2 13mm Spanner
3 17mm Spanner
INSTALLERS REQUIRED
1-2
COMPONENTS
#
DESCRIPTION
QTY
1 PSU1 – Socket & Bar Assembly
–
2 PSU1/2 – Dedicated Fixing Plate (Example)
–
3 PSC – Socket & Bar Assembly
–
4 PSC – Dedicated Projector Cradle (Example) –
5 PPSU – Socket & Bar Assembly
–
6 PPSU – Dedicated Projector Plate (Example) –
7 VSU – Socket & Bar Assembly
–
8 VSU – Dedicated Projector Plate (Example) –
9 PSU2 – Alternative Heavy duty T-Bar
–
10 CP1 – Standard Ceiling Plate (Example)
–
11 Dedicated Projector Fixing Screw Pack
–
12 Column Length
–
2
Revised 13/08/24
01865 767676 sales@unicol.com www.unicol.com
STEP 1 (ALL)
Loosen the 2 x Hex M8 or M10 hex screws and disconnect the upper and lower parts of the mount.
The upper part of these mounts generally fit onto a column or peg connected to a ceiling plate or wall arm. The lower part fixes to a projector. Cables run through column or peg and sockets to projector.
STPEPSU2 1/2
Using the fixing screws provided fit the lower part of the PSU to the fixing holes of the inverted projector.
The plate fixing to the projector is designed specifically for the projector ordered so may look differently to the one shown.
STEPPS3 C Rest the projector on its feet in the base of the cradle.
Each cradle is manufactured to suit the projector you have ordered the mount for. Balance and ventilation is taken into account within the design.
Revised 13/08/24
STEPPP4SU
Using the fixing screws provided fit the lower part of the PPSU to the fixing holes of the projector, on its side, lens pointing horizontally.
The plate fixing to the projector is designed specifically for the projector ordered so may look differently to the one shown.
3
01865 767676 sales@unicol.com www.unicol.com
STEVP S1 (UALL)
Using the fixing screws provided fit the lower part of the VSU to the fixing holes of the projector, on its side, lens pointing downward.
The plate fixing to the projector is designed specifically for the projector ordered so may look differently to the one shown.
STEPC3EILING SUSPENSION
STEP 2 (ALL)
Remove throughbolt in upper part of bar assembly socket and loosen grub screws. Align socket with column or peg. Thread cables through socket. Insert throughbolt and tighten. Tighten grub screws.
Hook lower part with projector over the 2 x M8/M10 hex screws. Cable up projector and set tilt angles then tighten M8/M10 hex screws. Set rotation angle by turning projector either way to finish installation.
Safety throughbolts must be used to secure the PSU. Grub screws are used to remove slack in the joint.
Revised 13/08/24
Beware of stretching cablies when adjusting angles. 4
Documents / Resources
 |
UNICOL PSU1 Series Direct Fixing Projector [pdf] Installation Guide PSU1, PSU2, PSC, PPSU, VSU, PSU1 Series Direct Fixing Projector, PSU1 Series, Direct Fixing Projector, Fixing Projector |