UGP-CTR-W-3-Y-ZZ Master Controller
“
Specifications:
- Product Name: Extension UGP-CTR-E-4-Y
- Number of Readers: 3
- Number of Identifiers: 10000
- Central Unit/Reader Protocol: OSDP V1/TTL/SSCP V2
- Central Unit/Hub Protocol: ONVIF A et C
- Power Supply: 12V(DC) 1.5A or 48V(DC) 1.5A (with POE
module) - Relay Information: NO/NC 48V / 2A max
- LED Output Information: LEDs 24V / 100mA max
- Logical Input Voltages: 0-24V max
- Power Supply Output: 12V / 250mA
- Interface E/S: TTL (Wiegand) or RS485 (OSPD/SSCP)
- Weight: 249g
- Mounting: DIN Rail Mounting
Product Usage Instructions:
Installation:
- Connect the power supply according to the specified voltage
requirements. - Mount the extension unit securely on a DIN rail using
appropriate tools. - Connect the readers and identifiers to the designated
connectors on the extension unit.
Configuration:
- Access the device using the provided identifiers (e.g.,
admin). - Configure the central unit/reader protocols based on your
system requirements. - Set up the logical inputs and outputs as needed for your access
control system.
Maintenance:
- Regularly check the power supply and connections for any signs
of damage or wear. - Clean the device and connectors periodically to ensure proper
functionality.
FAQ:
Q: What should I do if the LED outputs are not
functioning?
A: Check the power supply output and connections to ensure
proper voltage and wiring.
Q: How many identifiers can be stored in the device?
A: The device supports up to 10000 identifiers for access
control purposes.
Q: Can I chain multiple extension units together?
A: Yes, you can chain up to 8 extensions, but only the first one
can be powered by the master controller.
“`
Visuel
Contrôleur Maitre UGP-CTR-W-3-Y-ZZ
Informations générales
Extension UGP-CTR-E-4-Y
Contrôle de portes
Lecteurs
3
4
Identifiants
10000
Protocole centrale/lecteur Protocole centrale/hub
OSDP V1/TTL/SSCP V2
ONVIF A et C
Extension chaînable
De 0 à 8 maximum
Seule la première extension peut être alimentée par le contrôleur maître, les autres doivent être
alimentées par une alimentation indépendante.
Alimentation
Entrée d’alimentation Relais
12V(DC) 1,5A ou 48V(DC) 1,5A (avec module POE)
4
4
Infos relais Sortie LED
NO/NC 48V / 2A max
6
8
Infos sortie LED
LEDS 24V / 100mA max
Entrées logiques
12
12
Tensions entrées logiques
0-24V max
Sortie alimentation
4
5
Infos sorties alimentation
12V / 250mA
Lecteurs
Câble réseau / contrôleur Câble contrôleur / lecteur
Longueur max contrôleur / lecteur
Connecteurs
Conditions d’utilisation et de stockage Homologations Dimensions (H x l x L) Poids Montage Langues Garantie
Interface E/S
3 entrées lecteurs paramétrables :
4 entrées lecteurs paramétrables :
TTL (Wiegand) ou
TTL (Wiegand) ou
RS485 (OSPD/SSCP)
RS485 (OSPD/SSCP)
Exigences relatives au câblage
4 paires F/FTP/Cat6 2 paires torsadées blindées Type LIYCY-P
2x2x0,75 mm²
WIEGAND 100 m SSCP / OSDP 750m
Autres informations Bornier double colorés et débrochage (jusqu’à 1,5mm²) Port Ethernet 10/100 Mbps
De 0°C à 50°C
249g
CEM / Sécurité électrique / FCC / UL 60 x 95 x 160 249g
Montage sur rail DIN Français 2 ans
Unicacces-Groupe 24, chemin des vielles vignes 84240, La Tour d’Aigues NO762x02 Page 1 sur 4 Version du 19/05/2025
Montage : Montage sur Rail DIN
Montage Câblage
Types
Bornier coté contrôleur Maitre Bornier coté Extension 4L Bornier coté lecteur RS485 Bornier coté lecteur TTL Bornier coté Inputs Bornier coté vérouillage
Alimentation
+12V
(12Vdc)
GND
GND
+12V
/
GND
/
GND
/
/
/
/
/
/
/
/
/
/
Autoprotection &
Autoprotection
/
/
/
/
/
powertest*
Powertest
/
/
/
/
/
Inputs (bouton poussoir, bris de
IN A IN B
glace, contact de porte)
IN C
GND
IN A
/
IN B
/
IN C
/
GND
/
/
NC ou NO
/
/
NC ou NO
/
/
NC ou NO
/
/
COM
/
+12V
+12V
+12V
+12V
/
/
Reader
GND
GND
– ou GND
– ou GND
/
/
(lecteur de badge, clavier à code, …)
D0/L+ D1/LLEDG
D0/L+ D1/LLEDG
L+
D0
/
L-
D1
/
/
LEDG
/
/ / /
LEDR
LEDR
/
LEDR
/
/
NC
NC
/
/
/
NC
Relay
COM
COM
/
/
/
COM
(vérouillage)
COM
COM
/
/
/
COM
NO
NO
/
/
/
NO
MASTER to Extension &
+12V GND
+12V
/
GND
/
Extension to Extension
OUT A
IN A
/
OUT B
IN B
/
/
/
/
/
/
/
/
/
/
/
/
/
* Seulement si le contrôleur est dans un coffret d’alimentation
Mise en service
La configuration du contrôleur, incluant notamment le paramétrage des adresses IP et la gestion des droits
d’accès, s’effectue via son interface. Quitter le mode chantier
Pour sortir les contrôleurs du mode chantier, appuyez une fois sur le bouton RST situé à côté des
borniers rouges.
Connexion au contrôleur
1 Ouvrez un navigateur internet (Chrome, Mozilla, Edge, etc.). 2 Saisissez l’adresse IP du contrôleur dans la barre de recherche (192.168.1.150 par défaut). 3 Connectez-vous :
– Identifiant : admin
– Mot de passe : numéro de série du contrôleur (situé au dos du produit ou dans le coffret
d’alimentation). Reset IP des contrôleurs
Pour réinitialisé l’adresse IP, appuyez sur le bouton RST à coté du borner rouge pendant 5s jusqu’au clignotement de la led orange. (adresse IP par défaut : 192.168.1.150)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation.
NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
La directive Européenne 2012/19/EU sur les Déchets des Équipements Électrique et Électronique (DEEE), exige que les appareils électroniques usagés ne soient pas jetés dans le flux
normal des déchets électroniques. Les appareils usagés doivent être collecté séparément afin d’optimiser le taux de récupération et le recyclage des matériaux qui les composent et réduire l’impact sur la santé humaine et l’environnement. Le symbole de la poubelle barrée est apposé sur tous les produits pour rappeler les obligations de la collecte séparée. Les consommateurs devront contacter les autorités locales ou leurs revendeur concernant la démarche à suivre pour l’enlèvement de leur appareil. Conformément à la législation le niveau de conformité à la directive européenne 2014/30/UE, dite CEM, nos contrôleurs sont conformes aux normes : EN 50130-4 pour immunité et EN
55032 pour l’émission. Ils sont aussi conforme aux exigences essentielles des directives POC 2013/35/UE et répondent à la norme EN 62311 : 2008, selon la recommandation 1999/519/CE. Une copie de notre déclaration est disponible sur demande à l’adresse : qualité@unicacces-groupe.com Nos produits doivent être installer par des professionnels qualifiés. Dans le cadre d’une installation et/ou d’une utilisation incorrecte qui notamment ne suivent pas les recommandations indiquées (non exhaustives) ci-dessus, UNICACCES-GROUPE ne pourra être retenu pour responsable.
Unicacces-Groupe 24, chemin des vielles vignes 84240, La Tour d’Aigues NO762x02 Page 2 sur 4 Version du 19/05/2025
Visual
Master Controller UGP-CTR-W-3-Y-ZZ
General Information
Extension UGP-CTR-E-4-Y
Door Control
Readers
3
4
Identifiers
10000
Central Unit/Reader Protocol Central Unit/Hub Protocol
OSDP V1/TTL/SSCP V2
ONVIF A et C
Chainable extension
From 0 to 8
Only the first extension can be powered by the master controller; the others must be powered by
an independent power supply.
Power Supply
Input power Relay Relay information LED output LED output information Logical inputs Logical input voltages Power supply output Power supply output information
12V (DC) 1,5A or 48V (DC) 1,5A (with POE module)
4
4
NO/NC 48V / 2A max
6
8
LEDs 24V / 100mA max
12
12
0-24V max
4
5
12V / 250mA
Readers
Network cable / controller Controller / reader cable
Maximum length controller / reader
Connectors
Operating and storage conditions Certifications Dimensions H x W x L Weight Mounting Languages Warranty
I/O Interface 3 configurable
4 configurable
reader input:
reader inputs:
TTL (Wiegand) or
TTL (Wiegand) or
RS485 (OSPD/SSCP)
RS485 (OSPD/SSCP)
Wiring requirements
4 paires F/FTP/Cat6 2 shielded twisted pairs Type LIYCY-P
2x2x0.75 mm²
WIEGAND 100 m SSCP / OSDP 750 m
Other information Color-coded double terminal block and detachable (up to
1.5mm²) Ethernet port 10/100 Mbps
From 0°C to 50°C
EMC / Electrical Safety / FCC / UL
249g
60 x 95 x 160 249g
249g
DIN rail mounting
French, English, Spanish
2 years
Unicacces-Groupe 24, chemin des vielles vignes 84240, La Tour d’Aigues NO762x02 Page 3 sur 4 Version du 19/05/2025
Mounting : DIN rail mounting
Installation Wiring
Types
Controller-side terminal block Extension side terminal block RS485 reader-side terminal block TTL reader-side terminal block Inputs-side terminal block Locking-side terminal block
Power supply
+12V
+12V
/
(12V DC)
GND
GND
/
GND
GND
/
/
/
/
/
/
/
/
/
/
Autoprotection &
Autoprotection
/
/
/
/
/
powertest*
Powertest
/
/
/
/
/
Inputs (push button, glass break,
IN A IN B
IN A IN B
/ /
door contact)
IN C GND
IN C GND
/ /
/
NC ou NO
/
/
NC ou NO
/
/
NC ou NO
/
/
COM
/
+12V
+12V
+12V
+12V
/
/
GND
GND
– ou GND
– ou GND
/
/
Reader
D0/L+
D0/L+
L+
D0
/
/
(card reader, keypad, etc.)
D1/L-
D1/L-
L-
D1
/
/
LEDG
LEDG
/
LEDG
/
/
LEDR
LEDR
/
LEDR
/
/
NC
NC
/
/
/
NC
Relay
COM
COM
/
/
/
COM
(locking)
COM
COM
/
/
/
COM
NO
NO
/
/
/
NO
MASTER to Extension &
+12V GND
+12V GND
/ /
Extension to Extension
OUT A
IN A
/
OUT B
IN B
/
/
/
/
/
/
/
/
/
/
/
/
/
* Only if the controller is in a power supply enclosure
Deployment The controller’s configuration, including IP address settings and access rights management, is performed
through its interface.
Exit construction mode
To exit construction mode on the controllers, press the RST button located next to the red terminals
once.
Controller connection
1 Open a web browser (Chrome, Mozilla, Edge, etc.). 2 Enter the controller’s IP address in the search bar (192.168.1.150 by default). 3 Log in:
– Username: admin
– Password: controller’s serial number (located on the back of the product or in the power supply
enclosure).
Reset controller IP
To reset the IP address, press the RST button next to the red terminal block for 5 seconds until the
orange LED starts flashing. (Default IP address: 192.168.1.150)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. NOTE: The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. The European Directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE) requires that used electronic devices should not be disposed of in the normal flow of electronic waste. Used devices must be collected separately to optimize recovery rates and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed-out trash bin symbol is placed on all products to remind users of the separate collection obligations. Consumers must contact local authorities or their retailer regarding the procedure for removal of their device. In accordance with European legislation, the level of compliance with Directive 2014/30/EU, the EMC Directive, our controllers comply with the standards: EN 50130-4 for immunity and EN 55032 for emissions. They also comply with the essential requirements of the POC Directive 2013/35/EU and meet the EN 62311: 2008 standard, according to recommendation 1999/519/EC. A copy of our declaration is available upon request at: qualité@unicacces-groupe.com Our products must be installed by qualified professionals. In the event of improper installation and/or usage that does not follow the recommendations outlined above (non-exhaustive), UNICACCES-GROUPE cannot be held responsible.
Unicacces-Groupe 24, chemin des vielles vignes 84240, La Tour d’Aigues NO762x02 Page 4 sur 4 Version du 19/05/2025
Documents / Resources
 |
UNICACCESS UGP-CTR-W-3-Y-ZZ Master Controller [pdf] Owner's Manual UGP-CTR-W-3-Y-ZZ, UGP-CTR-W-3-Y-ZZ Master Controller, Master Controller, Controller |