1. Вступ
This manual provides essential information for the proper installation, operation, and maintenance of the Gentex 24VDC Plain White Horn Strobe, model GEC24-15/75PWW. This device is designed to provide audible and visual notification in fire alarm and emergency signaling systems. It features a 15/75 candela strobe and an integrated horn, operating on a 24VDC power supply. Please read this manual thoroughly before installation and use to ensure safe and effective operation.
2. Налаштування та встановлення
Proper installation is crucial for the reliable operation of the horn strobe. It must be installed by qualified personnel in accordance with all local and national electrical codes, and the instructions provided herein.
2.1 Розпакування та перевірка
- Carefully remove the horn strobe from its packaging.
- Inspect the unit for any signs of physical damage. Do not install damaged units.
- Verify that all components are present as per the packing list.
2.2 Місце монтажу
Select a mounting location that is suitable for the device's intended purpose, ensuring clear visibility of the strobe and unobstructed sound propagation from the horn. The unit is designed for wall mounting.
2.3 Інструкції з підключення
УВАГА: Disconnect all power to the circuit before wiring to prevent electrical shock or equipment damage.
- Ensure the power supply is a regulated 24VDC source, compatible with fire alarm signaling devices.
- Connect the wiring from the Fire Alarm Control Panel (FACP) to the terminal block on the back of the horn strobe unit. Observe proper polarity.
- Зверніться до схеми підключення, що додається до упаковки виробу, щоб дізнатися про конкретне призначення клем.
- Переконайтеся, що всі з’єднання надійні та належним чином ізольовані.

На цьому зображенні зображено передню частину view of the Gentex Horn Strobe unit. It features a white casing with a circular amber strobe lens at the bottom and an opening for the horn component at the top.
2.4 Встановлення пристрою
- Secure the mounting plate (if separate) to the wall or electrical box using appropriate screws.
- Attach the horn strobe unit to the mounting plate, ensuring it clicks securely into place.
- Verify that the unit is firmly mounted and cannot be easily dislodged.
3. Інструкція з експлуатації
The Gentex Horn Strobe is an automatic notification appliance designed to activate upon receiving a signal from a compatible Fire Alarm Control Panel (FACP).
3.1 Нормальна робота
Under normal conditions, the horn strobe remains in a standby state, drawing minimal current from the FACP.
3.2 Активація
- When the FACP detects an alarm condition (e.g., smoke, heat, manual pull station activation), it will send a signal to the notification appliance circuit.
- Upon receiving the activation signal, the horn strobe will simultaneously emit a loud audible alarm (horn) and a bright visual flash (strobe) at its rated candela setting (15/75 CD).
- The horn and strobe will continue to operate until the alarm condition is cleared and the FACP is reset.
4. Технічне обслуговування
Regular maintenance ensures the continued reliability and performance of your Gentex Horn Strobe.
4.1 Очищення
- Periodically clean the exterior of the unit, especially the strobe lens, using a soft, damp тканина.
- Не використовуйте абразивні засоби для чищення, розчинники або агресивні хімікати, оскільки вони можуть пошкодити пластикові компоненти.
- Переконайтеся, що волога не потрапляє всередину компонентів.
4.2 Testing and Inspection
- Regularly test the horn strobe in conjunction with the entire fire alarm system as per local codes and manufacturer recommendations (typically annually).
- During testing, verify that both the horn sounds clearly and the strobe flashes brightly.
- Inspect the unit for any visible damage, loose connections, or signs of wear.
- Any issues identified during inspection or testing should be addressed immediately by a qualified technician.
5. Вирішення проблем
If your Gentex Horn Strobe is not functioning as expected, consider the following common issues. For complex problems, always contact a qualified fire alarm technician.
5.1 No Horn Sound or Strobe Flash
- Перевірте живлення: Ensure the unit is receiving the correct 24VDC power from the FACP.
- Перевірте проводку: Verify all wiring connections are secure and correct, paying attention to polarity. Loose or incorrect wiring is a common cause.
- FACP Status: Confirm that the Fire Alarm Control Panel is in an alarm state and is sending a signal to the notification circuit. Check for FACP faults or troubles.
- Circuit Integrity: There might be an open circuit or short circuit in the notification appliance circuit. This requires FACP troubleshooting.
5.2 Weak Horn Sound or Dim Strobe Flash
- томtage Drop: Недостатній обtage at the device due to long wire runs or undersized wiring. Consult a technician to measure voltage на пристрої.
- Проблема з блоком живлення: The FACP's power supply might be overloaded or failing.
- Unit Damage: The unit itself may be faulty. If other troubleshooting steps fail, the unit may need replacement.
Важливо: Do not attempt to repair internal components. Refer all servicing to qualified fire alarm professionals.
6. Технічні характеристики
| Особливість | Деталь |
|---|---|
| Номер моделі | GEC24-15/75PWW |
| Бренд | Gentex |
| Тип | Рупорний строб |
| томtage | 24 В постійного струму |
| Рейтинг Candela | 15/75 CD |
| Колір | Звичайний білий |
| Монтаж | Настінне кріплення |
| Вага товару | 1.05 фунта |
| ASIN | B00IPQZ8CG |
| Дата першої доступності | 28 лютого 2014 р |
7. Гарантія та підтримка
For specific warranty information, please refer to the documentation included with your product or visit the official Gentex website. For technical support, service, or replacement parts, please contact Gentex customer service or your authorized Gentex distributor.
Корпорація Gentex
Webсайт: www.gentex.com
(Please note: Contact information may vary by region. Refer to your product's packaging or Gentex's official website for the most current support details.)