UbiBot GW1-V1.0.0 LoRa Smart Gateway User Manual

Wired Connectivity: Support Ethernet RJ-45 port 10/100 Mbps*
Auto-sensing Half/Full Duplex Switched Port*
Operating Environment: -20 to 60 degrees Celsius, 10-90%
RH

Product Usage Instructions

Device Operations

Switch On/Off: The device automatically
switches on/off when the power is plugged in/unplugged.
Setup Mode: Press and hold the button for
about 5 seconds until the device status indicator flashes red and
green alternately to enter setup mode.

Send Data: Press the button once under
power-on state to connect to the network and send data.
Reset to Default Settings: Press and hold the
button for about 15 seconds until the red device status indicator
blinks to restore factory settings.

Device Setup Options

Option 1: Using Mobile App
Download the App from www.ubibot.com/setup or search for
‘Ubibot Connect’ on the AppStore or Google Play.
Option 2: Using PC Tools
Download the tool from www.ubibot.com/setup. This desktop app
is helpful in device setup and data management.

Setup Using the App for WiFi Connection

Launch the App, tap + on the home page to add your device, and
follow the in-app instructions for setup. Refer to the
demonstration video at www.ubibot.com/setup for guidance.

Setup Using the App for Ethernet Cable Connection*

Step 1: Connect the device with power supply
and plug in the Ethernet cable.

Step 2: Launch the app, tap + on the home page
to add your device, and follow the in-app instructions for
setup.

Setup Using PC Tools

Step 1: Launch the App, connect your device to
the computer using the Type-C USB cable.

Step 2: In the PC Tools, set up the device on
WiFi or other connectivity options as needed.

Frequently Asked Questions (FAQ)

Q: What are the supported frequency bands for the LoRa Smart
Gateway GW1?

A: The LoRa Smart Gateway GW1 supports EU868 / US915 / AU915 /
IN865 / RU864 / KR920 / AS923 frequency bands.

Q: How can I reset the device to its default settings?

A: To reset the device to default settings, press and hold the
function button for about 15 seconds until the red device status
indicator blinks, then release the button.

“`

View Fullscreen

LoRa Smart Gateway GW1
User Manual

This user manual serves as a general guidance for all types of UBIBOT® LoRa Smart Gateway. Some features, which are marked with asterisk, are available only for specific versions. Please refer to related instructions according to the version you purchased.
PACKAGE LIST

1 Device

2 Adapter

INTRODUCTION
1. Basic Features Introduction
DC12V power port Indicator RJ45 Interface TYPE-C Button

LoRa Communication Indicator Status Indicator Network Indicator
1

2.Device Operations

Switch On/Off Setup Mode
Send data Reset to Default Settings

After the power is plugged in/unplugged, the device will Switch On/Off automatically.
With the device switched on, press and hold the button for about 5 seconds until the device status indicator flashes red and green alternately. Release at this time to enter the setup mode.
Under power-on state, press the button once, the green device status indicator will flash, then connect to the network and send data.
Under power-on state, press and hold the function button for about 15 seconds until the red device status indicator blinks, then release the button to restore factory settings.

DEVICE SETUP OPTIONS

Option 1: Using Mobile App
Download the App from www.ubibot.com/setup, or search for ‘Ubibot Connect’ on the AppStore or Google Play.

We recommend you try to use the PC Tools in case the App setup fails, because the failure may be due to mobile phone incompatibility. The PC Tools is much easier to operate and suitable for both Mac and Windows.

Option 2: Using PC Tools
Download the tool from www.ubibot.com/setup. This Tool is a desktop app for device setup. It is also helpful in checking setup failure reasons, MAC address, and offline charts. You can also use it to export offline data stored in the device internal memory.
SETUP USING THE APP FOR WiFi CONNECTION
Launch the App and log in. On the home page, tap “+” to start adding your device. Then please follow the in-app instructions to complete the setup. You can also view the demonstration video at www.ubibot.com/setup for step by step guidance.

Via our app and web console (http://console.ubibot.com), you are able to view the readings as well as configure your device, such as create alert rules, set data syncinterval, etc. You can find and watch the demonstration videos at www.ubibot.com/setup.
SETUP USING THE APP FOR ETHERNET CABLE CONNECTION*
STEP 1. Connect the device with power supply and plug the Ethernet cable. STEP 2. Launch the app and log in. On the home page, tap “+” to start adding your device. Then please
follow the in-app instructions to complete the setup. You can also view the demonstration video at www.ubibot.com/setup for step by step guidance.
SETUP USING PC TOOLS
STEP 1. Launch the App and log in. With the device switched on, use the Type-C USB cable provided to
connect your device to the computer. The PC Tools will automatically scan and recognize the product ID and enter the device page.
STEP 2. Click “Network” on the left menu bar. There, you are able to set up the device on WiFi for all the
models. For the SIM or Ethernet cable setup, please click on the corresponding button to continue.
3

DEVICE SPECIFICATION
EU868 / US915 / AU915 / IN865 / RU864 / KR920 / AS923 WiFi 2.4GHz, channel 1-13 Support Ethernet RJ-45 port 10/100 Mbps* Auto-sensing Half/Full Duplex Switched Port* Device working environment: -20 to 60, 10-90%RH

ABS Type-C, DC 12V/1A power supply 190mm x 190mm x 40mm Built-in Memory: 300,000 sensing data

FAQ
1. Device network configuration failure reasons
Please check whether the WiFi account password is correct; Please check whether the router is working properly and the network connection is normal; Please make sure the device has entered the WiFi configuration mode; Please check whether the WiFi band is 2.4GHz and the channel is between 1~13; Please check the WiFi channel width is set to 20MHz or auto mode; WiFi security type: GW1 supports OPEN, WEP and WPA/WPA2-personal; Poor signal strength, please check the WiFi or cell phone data traffic signal strength.
2.Ethernet network* configuration failure reasons
Please check whether the network cable is properly connected to the equipment; whether the network cable is intact; whether the connected network can access the Internet; If the above points are not abnormal, and you still cannot activate the device, you need to check whether the network environment allows DHCP (automatic IP allocation) devices to access the network; or re-scan the device QR code, select Ethernet access (advanced mode), and follow the APP prompts to manually assign IP to the device.

TECHNICAL SUPPORT
The UbiBot team is glad to hear your voice of our profucts and services. For any questions or suggestions, please feel free to create a ticket in the UbiBot app. Our customer services representatives respond within 24 hours and often in less than an hour. You can also contact the local distributors in your contry for localized service. Please go to our website to view their contacts.
WARRANTY INFORMATION
1. The warranty period for this product is one year from the date of purchase. The buyer is required to submit a valid proof of purchase. During the warranty period, free repair will be provided for any failure caused by the quality of the product under normal use. The mailing cost of the returned product is the responsibility of the sender (one way).
2. The following cases are not covered by the warranty:
The product is out of warranty; product failure or damage caused by incorrect or improper operation not in accordance with the product use instructions, configuration instructions, and product maintenance instructions; accidental or man-made damage to the product, such as exceeding the temperature and humidity range of the equipment, water-caused damage, including natural water, such as water vapor, etc., fall, abnormal physical force, deformation, cable breakage, etc.; damage due to natural wear and tear, consumption and aging, etc. (including shells, cables, etc.); failure or damage caused by unauthorized dismantling of the product without permission; failure or damage caused by force majeure, such as earthquake, fire, lightning strike, tsunami, etc.; other non-product design, technology, manufacturing, quality and other issues caused by the failure or damage.
5

PRODUCT MAINTENANCE INSTRUCTIONS
Please always follow the instructions contained in this manual. Always mount the device on a stable surface. Keep away from acidic, oxidising, flammable or explosive substances. When handling the device, avoid using excessive force and never use sharp instruments to try and open it. Please use common USB Cable or original charger, Otherwise, It may resultto danger. When you use a charger for charging, adapter shall be installed nearthe equipment and shall be easily accessible. Manufacturer of Power adapter: Huizhou Guoaotong Technology Co., Ltd. Parameters of Power adapter: Input: AC 110~240V, 600mA, 50/60Hz. Output: DC 12V, 1000mA.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particula installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approvedby manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
6

V1.0.0

Documents / Resources

UbiBot GW1-V1.0.0 LoRa Smart Gateway [pdf] User Manual
GW1-V1.0.0, GW1-V1.0.0 LoRa Smart Gateway, GW1-V1.0.0, LoRa Smart Gateway, Smart Gateway, Gateway

References

User Manual