TG-LX3F82418 LanderX Running Board
Installation Guide
BEFORE INSTALLATION
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE0 CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT
TORQUE VALUES
| Fastener Size | Class 8.8 Torque (ft-lbs) | Class 10.9 Torque (ft-lbs) |
| 6mm | 6-7 15-16 |
6-7 |
| 8mm | 22-23 | |
| 10mm | 31-32 | 44-45 |
| 12mm | 54-55 | 78-79 |
| 14mm | 87-88 | 125-126 |
Parts List
x1 Driver/Left TYGER LanderX
x1 Passenger/Right TYGER LanderX
x1 Driver/Left Front Mounting Bracket A
x1 Driver/Left Center Mounting Bracket B
x1 Driver/ Left Rear Mounting Bracket C
x1 Passenger/Right Front Mounting Bracket D
x1 Passenger/Right Center Mounting Bracket E
x1 Passenger/Right Rear Mounting Bracket F
x12 8mm x 25mm Combo Bolts
x12 10-1.5mm x 30mm Hex Bolts
x12 10mm Lock Washers
x12 10mm x 27mm OD x 3mm Flat Washers
Reference the letters printed on the brackets to determine mounting locations
Bottom View
ATTENTION: Refer to the D or P labelling on the tubes to determine the Driver or Passenger side steps.
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT.
READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
STEP 1
panel. Locate the threaded mounting holes in the rocker panel toward the front wheel opening (Fig 1). Remove the plastic plugs covering the mounting holes.
Passenger/Right side Installation Pictured
STEP 2
Select the Passenger/Right Front Mounting Bracket D (Fig 2). Attach Bracket to passenger/right front location with (2) 10mm x 30mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers (Figs 2 & 3). DO NOT fully tighten hardware.
STEP 3
Move to the center of the vehicle and locate the threaded mounting holes (Fig 4). Select the Passenger/Right Center Mounting Bracket E (Fig 5). Attach the Bracket to the threaded holes with the included (2) 10mm x 30mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers (Fig 6). DO NOT fully tighten hardware.
Passenger/Right side Installation Pictured
STEP 4
Move to the last threaded holes closest to the rear wheel opening. Select the Passenger/Right Rear Mounting Bracket (Fig 5). Repeat STEP 3 to attach the Rear Mounting Bracket (Fig 7).
IMPORTANT: Rear Mounting Brackets feature a small hole for identification purposes.
Passenger/Right side Installation Pictured
STEP 5
Carefully unwrap the TYGER LanderX. Select the Passenger/Right TYGER LanderX. Line up the TYGER LanderX with the (3) Mounting Brackets. Attach the TYGER LanderX to the Brackets with the included (6) 8mm x 25mm Combo Hex Bolts (Figs 8-12).
Passenger/Right side Installation Pictured
STEP 6
Level and adjust the TYGER LanderX and tighten all hardware.
STEP 7
Repeat STEPS 1-6 for driver/left side TYGER LanderX installation.
STEP 8
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
Documents / Resources
 |
TYGER TG-LX3F82418 LanderX Running Board [pdf] Installation Guide TG-LX3F82418 LanderX Running Board, TG-LX3F82418, LanderX Running Board, Running Board, Board |