Zigbee Wall switch
User Manual
Features
- Need to be used with Tuya Zigbee gateway
- Can be controlled through iOS mobile phone/Android mobile phone
- Support “Smart Life” and “Tuya Smart” APP
- Voice control: compatible with Alexa and Google home
- Tmall Genie or small speaker
- Timing function: automatic on/off with timing function
- Delicate appearance, fireproof material, safe and durable
- Overload protection, convenient to replace your traditional mechanical switch (Neutral line required)
- Intelligent scene
- Equipment group
Security information
Risk of electric shock: Improper operation may cause personal injury and property damage. If you are unsure about any part of these instructions, please seek professional help from a qualifiedelectrician.
Product information
Wireless standard: Zigbee 3.0
Working voltage: AC 100-250VAC 50/60Hz
Load power: 1000W/Gang
Maximum load current: 10A
Power consumption: ≤ 0.5W
Working temperature: 0 ℃~40 ℃
Size: 86x86x40.5mm
Installation
Please note that:
- Make sure that the power supply on the circuit breaker is turned off before wiring.
- Neutral wire is required. Confirm that the wall box contains the neutral wire (usually white). If the wall box does not have a neutral wire, please try to install the switch at another place in the home or call a professional electrician.
- The wire color indicated in this manual is the common color, which may be different in some houses.
- Ensure that the wire conductor is firmly fixed on each wire.
- Before wiring, ensure that the Wi-Fi signal is stable and works normally.
- If you have no wiring experience, please call a professional electrician.
Step 1:
- Close the circuit breaker and use the electrical tester to test the power supply.
- Make sure the switch is closed before wiring.

Step 2:
- Remove existing wall panels, Turn on the power supply at the circuit breaker and use the electrical tester to check which wire is the line route, When approaching the line, the tester will flash or beep
- Turn off the power supply at the circuit breaker. If it is powered off, use an electrical tester to pull out the existing switch, Mark line lines and other wires, Disconnect the power supply and remove the wire from the existing switch with pliers.
- Connect the switch wires to the wires in the wall box with wire conductors according to the wiring diagram.

Step 3:
Use the screws provided to install the switch and clip the wall panel onto it.
Step 4:
Turn on the power again at the circuit breaker, and then turn on the light.
Wiring diagram
Live wire connection “L” terminal, The zero line is connected to the “N” terminal, Lighting line is connected to “L1, L2, L3” terminals

1Gang switch lighting wire connection: “L1” terminal

Add device:
4.1 Add devices to “Smart Life” or “Tuya Smart” APP
Step 1: download and install “Smart Life” or “Tuya Smart” APP: scan the QR code below or search directly in the mobile app store.
http://smartapp.tuya.com/smartlife
http://smart.tuya.com/download
Note: Before adding equipment, add Zigbee gateway Step 2: Connect the equipment to the power supply and connect the wires according to the wiring diagram. Press the switch button, the indicator light will flash, enter the configuration mode, and the configuration indicator light will go out after the configuration is successful
Step 3: Open the Tuya smart app, click Zigbee to turn off the device, click Add Device, and select Zigbee switch. Click Add to complete the addition.
How to use smart speakers to control devices, such as Amazon Alexa, Google Assistant, Tmall Genie or Xiaodu?
Open the Smart Life APP to enter the “My” interface and find the user guide corresponding to the smart speaker.
[Note: Before using smart speakers, please log in to your account on Amazon Alexa, Google Assistant, Tmall Genie or Xiaodu.]


Documents / Resources
![]() | RF433 ZigBee Plus Smart Wall Switch |
References
- User Manualmanual.tools
