TUISS Shutter Blinds Installation Guide

TUISS-LOGO

TUISS Shutter Blinds

TUISS-Shutter-Blinds-PRODUCT

Before you begin

  • Your shutters will arrive in separate parcels. The longer and slimmer parcel will contain the sections of the frame and the flatter rectangular parcel will contain the panels.
  • A maximum of two panels will be packed together, so for wider sets of shutters there will be additional parcels containing the additional panels.
  • The fixing kit will be packed in the frame parcel.TUISS-Shutter-Blinds-FIG-1

Your fixing kit

TUISS-Shutter-Blinds-FIG-2

Installation Guide

Assemble the frame

Start by unpacking all of the frame pieces, then laying them face-down.

TUISS-Shutter-Blinds-FIG-3

Line up all the corners, then insert the Hoffman keys from your fittings kit to join the frames securely together. The key can be a little tight, so you may have to give it a few taps with a hammer to fully insert it.

Top Tip
Use the packaging your shutters arrived in to protect them during this stage – open out one of the boxes so you can lay the shutter down on that and avoid any risk of scratching it. Like wise, you may need to gently hammer the hoffman keys into place as they’re quite tight, so you can use a strip of cardboard over the key as you’re hammering.

Wider shutters over 1250mm will have a ‘T-Bar’ provided with the frame.
The T-Bar is fitted vertically in the centre of the frame, providing extra support for the shutter.
To fit the T-Bar, simply slot it into place in the centre of the shutter and use 4 of the 75mm screws provided – 2 at the top of the frame and 2 at the bottom – to secure it in place. The screw holes will be pre-drilled in your shutter frame so that the T-Bar can be located correctly and easily.

TUISS-Shutter-Blinds-FIG-4

Pre-drill the fixing holes in the frame

Assemble the frame, then drill the holes you’ll be putting screws through to fit the shutter. For the sides, make your holes roughly in line with the centre of each hinge. For the top and bottom, make the holes roughly 10-15cm in from the sides.

TUISS-Shutter-Blinds-FIG-5

Ensure the frame sits level in the window

Place the assembled frame in the recess and use a spirit level to make sure that it is sitting perfectly straight on all sides.

TUISS-Shutter-Blinds-FIG-6

Make sure you also use the spirit level on the front of the frame, on all sides, to ensure there’s no ‘twist’ to the frame.

Install the frame

Making sure that the frame stays still and level, push the drill through each of the fixing holes you made in the frame and drill a small pilot hole in the surface you’re fixing the shutter to (the inside of the recess). Drill through the plaster as far as the timber beneath. You should now be left with shallow pilot holes all around the recess – two for each side, the top and the sill.

TUISS-Shutter-Blinds-FIG-7

Give the frame another level check, then use the 75mm screws from your fixing kit to secure the frame in place.

TUISS-Shutter-Blinds-FIG-8

Install the panels

Start by loosening the frame hinges, as this will make aligning the two parts of the hinge easier (one part is fixed to the frame, the other part is fixed to the panel). This will also allow you enough room to slot the hinge pins into place.

TUISS-Shutter-Blinds-FIG-9

Next, place the panels in position inside the frame.

TUISS-Shutter-Blinds-FIG-10

Top Tip
It is normal for the panels to rest on the bottom frame of the shutter when closed, this does not require any adjustment.

Finishing

Tighten the hinge screws and insert a final screw in the centre hole for each frame hinge, to lock the hinges in place.

TUISS-Shutter-Blinds-FIG-11

Next, attach the magnets that help to keep the panels closed.
Use the centre point of your panels as a guide to line up your magnet. Mark the screw hole positions on the shutter’s frame.
Make the same marks on your magnet riser, then pre-drill the holes in the riser. Use 2x 18.5mm screws to fix the magnet and riser to the inside of the shutter’s frame, one at the top of the frame and one at the bottom.

TUISS-Shutter-Blinds-FIG-12

Finally, attach the metal strike plates to the back of the shutter panels, so that they’re in line with the magnets.

Finally, cover the screws you used to fix the frame inside the recess:

TUISS-Shutter-Blinds-FIG-13

Top Tip
As a final finishing touch, use decorator’s caulk to fill in any gaps around the edges of the frame (usually only required for Inside Recess Frames).

Frequently Asked Questions

  • Q: How many panels can be packed together in one parcel?
    A: A maximum of two panels will be packed together. Additional panels for wider sets will be in separate parcels.
  • Q: What should I do if the Hoffman keys are tight to insert?
    A: Give them a few taps with a hammer for a secure fit, or use a strip of cardboard over the key while hammering.
  • Q: How do I ensure the T-Bar is correctly fitted for wider shutters?
    A: Slot the T-Bar into the center of the frame and secure it with 75mm screws at the top and bottom. The screw holes will be pre-drilled for easy installation.

Documents / Resources

PDF thumbnailShutter Blinds
Installation Guide · PO, Shutter Blinds, Shutter, Blinds

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.