PEEM-S100 WiFi Smart Meter
“
Specifications:
- Model: PEEM-S100
- Communication: WiFi
- Installation Mode: DIN Rail
- Wiring Mode: CT Connected
Product Introduction:
The Smart Meter is a power meter that uses WiFi communication.
It is installed in the home distribution box, collects voltage,
current, power, and other information of the power grid, and
transmits it to microinverter or micro storage unit through the
WiFi network. It assists microinverter or micro storage unit in
performing control functions such as zero-export function.
Product Installation:
Confirm the Phase of the Circuit:
Warning: The maximum passing current of the
Smart Meter is 100A. The load current in this circuit cannot exceed
this upper limit.
Pre-installation Check:
Check the Product and Accessory for any signs of damage. If
damage is found, contact your dealer.
- Meter * 1
- Antenna * 1
- CT * 1
- SN Label * 1
Check the Installation Environment and Location:
Install the Smart Meter:
Danger: Installers must ensure that the
three-phase switch as well as all other switches remain in a closed
state during the whole operation process. Be cautious not to touch
the exposed conductive part on the grid-side of the three-phase
switch to prevent electric shock.
Monitoring System:
Download and Install APP
- iOS users can directly search for TSUN Smart in the APP Store
and download the software. - Android users can directly search for TSUN Smart in Google Play
and download the software. - Android users who cannot access Google Play can scan the QR
code provided to download and install TSUN Smart.
FAQ:
Q: What should I do if I encounter difficulties during
installation?
A: If you face challenges during installation, refer to the user
manual for troubleshooting steps or contact customer support for
assistance.
“`
PEEM-S100 WiFi Smart Meter_User Manual _ EN
Update Instructions
This section records the updates of the Sm art M eter User M anual.
Version
Update Date
Content
V1.0
2 0 2 4 -11 -8
Initial version
Read Before Use
T his m anual contains im portant instructions for S m art M eter, w hich m ust be read com pletely before installing or debugging the equipm ent. For safety reasons, only qualified technicians who have been trained or have proven skills can install and m aintain this Sm art M eter under the guidance of this docum ent.
This m anual is applicable to the following products:
Model
Communication
Installation Mode
Wiring Mode
P E E M -S 100
W iFi
DIN Rail
CT Connected
The following security sym bols are used in this m anual. Before installing or operating the system , fam iliarize yourself with these sym bols and their m eanings.
Identification
Explanation
Danger:
Danger indicates a dangerous situation that m ay cause fatal electric shock, other serious personal injury, or fire danger.
Warning:
W arnings indicate instructions that m ust be fully understood and followed to avoid potential safety hazards, including equipm ent dam age or personal injury.
Note:
Notes indicate that the described operation should not be perform ed. Before continuing, readers should stop using and
fully understand the explained operation.
Product Introduction
System Introduction
Sm art M eter is a power m eter that uses W IFI com m unication. It is installed in the hom e distribution box, collects voltage, current, power and other inform ation of the power grid, and transm its it to m icroinverter or m icro storage unit through the W IFI network. It assists m icroinverter or m icro storage unit in perform ing control functions such as zero-export function. Exam ple : Sm art M eter and TSUN Products integrated with W iFi
Product Introduction
A
C o n n e c to r
D
B
Antenna Port
E
C
Status Light
Screen Buttons
Product Installation
Confirm the Phase of the Circuit
If this sm art m eter is installed on a single-phase power grid, ignore this section and proceed to the next step, “Install the Sm art M eter”. If this sm art m eter is installed on a three-phase power grid, it is necessary to confirm the installation position of the m eter according to the following m ethod. Confirm the corresponding switch and the phase of the m icroinverter or m icro storage unit in the household distribution box. As shown in the figure below, it is necessary to confirm which phase of the m icroinverter or m icro storage unit is in. The sm art m eter m ust be installed next to the electricity m eter. W hen the m eter is in the sam e phase as the corresponding m icroinverter or m icro storage unit, the m icroinverter or m icro storage unit can turn on the zero export function.
· Method 1: If the circuits or devices controlled by each switch are clearly m arked on each singlephase switch in the household distribution box, the installer can directly find the circuit switch that controls the m icroinverter or m icro storage unit. · Method 2: If the control circuit of each single – phase switch in the household distribution box cannot be clearly distinguished, the installer can consult the household about the house power grid wiring diagram , obtain relevant inform ation by querying the drawing, and find the circuit switch that controls the m icroinverter or m icro storage unit.
· Method 3: If relevant inform ation cannot be found in the distribution box or drawing m aterials, the installer can quickly find the corresponding circuit switch according to the following steps. 1. S te p 1 : C o n n e ct a n e a sily-o b se rva ble h o u se h o ld a p p lia n ce (su ch a s a n e le ctric fan, desk lam p, etc.) to the socket that is ready to have the m icroinverter or m icro storage unit installed. 2. S te p 2 : Tu rn o n th e h o u se h o ld a p p lian ce a n d p u t it in w o rkin g m o d e (fo r exa m p le , turning on the electric fan or desk lam p). 3. S te p 3 : Tu rn o ff th e sin g le -p h a se sw itch e s in th e h o u se h o ld d istrib u tio n b o x o n e after another, and observe the status of household appliances at the sam e tim e. If the household appliance used for observation stops working after closing a singlephase switch (for exam ple, the electric fan stops rotating, the desk lam p goes out), then the single-phase switch is the control switch of the corresponding circuit. After finding the corresponding circuit switch, install the sm art m eter on the bus (or connection line) between the three-phase switch and the single-phase switch. For exam ple, if the sm art m eter is installed in the L1 phase, the wiring should be as fo llo w s .
Warning: The m axim um passing current of the Sm art M eter is 100A. The load current in this circuit cannot exceed this upper lim it.
Pre-installation Check
Check the Product and Accessary
Although TSUN’s products have passed stringent testing and are inspected before leaving the factory, it is possible that the products m ay be dam aged during transportation. Please check the product for any obvious signs of dam age. If such signs are present, contact your dealer as soon as possible.
Meter * 1
Antenna * 1
CT * 1
SN Label * 1
Check the Installation Environment and Location
W hen selecting the installation location, the following conditions should be adhered to: · Install the PEEM -S100 close to or within the hom e distribution box. · Avoid electrom agnetic interference that could affect the proper operation of electronic equipm ent. · Use a m obile phone to assess the W i-Fi signal strength at the installation site. If the W i-Fi signal is weak, attem pt to install the PEEM -S100 at an alternative location or relocate the W i-Fi router.
Install the Smart Meter
· Step 1: Turn off the three-phase switch and all single-phase switches of the distribution box.
Danger: Installers m ust ensure that the three-phase switch as well as all other switches rem ain in a closed state during the whole operation process. M eanwhile, be cautious not to touch the exposed conductive part on the grid – side of the three – phase switch to prevent electric shock.
· Step 2: Install the Sm art M eter on the rail of the distribution box.
· S tep 3: C onnect the L (Live) and N (N eutral) cables to port 11 and port 14 respectively. Then connect the C T cable to port 4 (using the R ed C able) and port 5 (using the Black Cable).
· Step 4: M ount the CT onto the correct L cable. The arrow direction m arked on the CT should be oriented towards the inverter side.
· Step 5: Connect the W i-Fi antenna cable to the PEEM -S100. Place the antenna outside the distribution box to ensure a strong W i-Fi signal.
· S tep 6: U pon confirm ing the correct w iring of the m eter, turn on the three-phase switch and the single-phase switch.
Monitoring System
Download and Install APP
D o w n lo a d a n d in sta ll the “T S U N S m a rt” A P P. 1. IO S u se rs ca n d ire ctly se a rch fo r “T S U N S m a rt” in th e A P P S to re a n d d o w n lo a d the software. 2. A n d ro id u sers ca n d ire ctly se a rch fo r “T S U N S m a rt” in G o o g le P la y a n d download the software. 3. A n d ro id u sers w h o ca n no t a cce ss G o o g le P la y ca n sca n th e Q R co d e b e lo w to download and install “TSUN Sm art”.
R e g iste r a n a cco u n t a n d lo g in to th e A P P.
W hen registering, you can choose to be an installer or an end-user.
The rooftop solar plant which uses m icroinverters needs to be built by a professional installer. Please register as an “installer” and follow the subsequent instructions to execute the APP operation.
The DIY balcony storage plant which uses m icro storage units is built by end – users, but the installation of sm art m eter still needs to be done by professionals. Please register as “end – users” and follow the subsequent instructions to execute the APP operation.
Operation Steps (Professional Installer + Microinverter)
· Step 1: Click “+” to create a soalr plant. After filling in the plant inform ation, click “Save” to com plete the solar plant creation.
Note: The system type is “Photovoltaic + Grid + Load”.
· Click “Add Datalogger” and scan the QR code on the m eter to com plete the device addition.
· First,click “…” in the upper right corner and select “W IFI Configuration”. Then select the corresponding m eter and click “S tart C onfig”. Finally, select the W IFI you want to connect to, enter the W IFI password and click “Start Config” again.
After approxim ately 10 seconds, the W iFi configuration will be com pleted successfully, and the m eter data w ill be uploaded to the server.
· Step 4: Enter the “Device” page and click “M eter Configuration”. Set the installation site to “Grid” and set the arrow to “Energy Purchase”. Click “Save” and finish the configuration.
· Step 5: Click “… ” on the plant hom e page and click “Anti-Reverse Flow Configuration”. Choose “Turn O n” and set the total plant power and offset value
(Norm ally set to 0 W ). Reconfirm all the inform ation and click “O K”. W aiting for around 300 seconds and com plete this configuration.Check the status in the device list after the configuration.
Note: All devices m ust be online during the configuration. If there are any issues, you can try reconfiguring.
Operation Steps (DIY End-Users + Micro Storage Unit)
· Step 1: Click “Create Plant”. After filling in the plant inform ation, click “Save” to com plete the plant creation.
· Step 2: First, click m enu button in the upper right corner and then select “Device List”. Next, click “Add Device” and under the “Accessories” m enu, select “Sm art M eter” device. Finally, scan the Q R code on the m eter to com plete the device addition.
· Step 3: In the “Device List”, click “W IFI Config”. Select the corresponding m eter and click “Start Config”. Select the W IFI you want to connect to, enter the W IFI password, and click “Start Config” again.
After approxim ately 10 seconds, the W iFi configuration will be com pleted successfully, and the m eter data w ill be uploaded to the server.
· Step 4: Click m enu button on the plant hom e page and click “Control Strategy”.
Click “G o to Contiguration” . Turn on the Anti-Reverse Flow Contiguration.
Appendix:
PEEM-S100
AC Input
G rid Type
Input AC Voltage
Input AC Frequency
Max. Current per phase
Power Consum ption per phase
Single phase 230V
50 / 60 Hz 100A 1 W
Communicatio W i-F i Typ e n
W i-Fi Frequency Range
W IFI (802.11 b/g/n) 2 4 0 0 M H z-2 4 8 3 .5 M H z
M axim um Distance to Router (Open Space)
100m
Control Accessary
Mechanical Data
Bluetooth Type
BLE 5.0
Bluetooth Frequency Range
2 4 0 0 M H z-2 4 8 3 .5 M H z
M axim um Distance to m obile phone
50m
(Open Space)
Connection Lim it
5 M icroinverters
Com m unicate to Server
300 s
Com m unicate to M icroinverter
300 ms
External Antenna
Yes
Cable length of antenna
2m
External CT
1
Cable length of CT
2m
CT Type
16mm
Dim ension(m m )
36 * 90 * 90
W eight (g)
130
A m bient Tem perature(°C )
-20~+55
M ounting System
Rail m ounted (35m m )
Indicator Light
1 * LED
Altitude(m )
< 2000
Relative Hum idity
0 – 95%, No condensation
Documents / Resources
 |
TSUN PEEM-S100 WiFi Smart Meter [pdf] User Manual PEEM-S100 WiFi Smart Meter, PEEM-S100, WiFi Smart Meter, Smart Meter, Meter |