TrolMaster DCC-1 Dual Condition Controller
The DCC-1 allows users to use a DS type plug-in style module, and the DCC-1 to have two conditions/variables controlled from a single device DS module. Follow the steps below to install your DCC.
DCC-1 / Dual Condition Controller
In some circumstances, it is necessary to have a single device turned on (or off) when a second control condition is activated. There are many examples of this but the most common are:
- Turn on an exhaust fan at night (or day) to reduce CO2, temp, or humidity.
- Turn on an exhaust fan at night using a recycling timer, OR when Humidity is too high
OR - Shut off a CO2 device when an exhaust fan is running
- Shut off lights if the temperature gets too warm within the area
The DCC-1 is designed to be used in combination with one of TrolMaster’s plug-in style modules… the DSC-1, DSH-1&2, DST-1&2 and the DSP-1. Once the DCC-1 is connected to the plug-in DS module using an RJ12 cable, the DCC-1 will act in concert with that DS module to control whatever device is connected to the DS module.
Product Usage Instructions
To install the DCC-1
- First, you will plug the DS module into a power source near the equipment that will be controlled by the DS module.
- Connect a RJ12 cable from the DS module’s communication port to the female port on the DCC-1.
- Plug the DCC-1 into a splitter and RJ cable that is connected back to the Device port on the HCS-1.
Note: The DCC-1 gets plugged inline with the DS modules RJ12 cable. - Next you will select the desired mode on the DCC-1 by using the SET button to select the correct module type, and then pressing the Address button on the DCC-1. The DCC-1 is now connected to the HCS-1 and assigned as the device station you selected on the DCC1
- Go to the HCS-1 and find the device settings for the DCC-1.
- You can now change the settings for the DCC-1 module.
- If you have not already addressed the DS module that the DCC-1 is connected to, press the addressing button to address the DS module.
- Got to the HCS-1 and enter the settings for the DS module.
- The last thing to do is to decide whether or not to activate the interlock function or not.
Interlock Function
The DCC-1 can operate in two modes with the Interlock function:
- Interlock ON: Both conditions must be activated together for device activation.
- Interlock OFF: Either condition can activate the DS module individually.
To toggle between Interlock modes, press and hold the Interlock button for 3 seconds.
Specifications
- Product Name: Trolmaster DCC-1
- Function: Dual Condition Controller
- Compatible Modules: DSC-1, DSH-1&2, DST-1&2, DSP-1
- Communication: RJ12 cable
FAQS
Q: What modules are compatible with the DCC-1?
A: The DCC-1 is designed to work with TrolMaster's plug-in style modules such as DSC-1, DSH-1&2, DST-1&2, and DSP-1.
Q: How do I install the DCC-1?
A: Follow the installation steps provided in the user manual including connecting the DS module, setting modes, and adjusting settings on the HCS-1.
Q: How do I toggle between Interlock modes?
A: Press and hold the Interlock button on the DCC-1 for 3 seconds to switch between Interlock ON and OFF.
Q: Can I use the DCC-1 with multiple devices?
A: The DCC-1 can control multiple devices connected to compatible DS modules by following the installation and setup instructions.
Documents / Resources
 |
TrolMaster DCC-1 Dual Condition Controller [pdf] Instruction Manual DSC-1, DSH-1 2, DST-1 2, DSP-1, DCC-1 Dual Condition Controller, DCC-1, Dual Condition Controller, Condition Controller |