Trimble-LOGO

Trimble GD0375-V2 Wireless Line Riding Tensiometer

Trimble-GD0375-V2-Wireless-Line-Riding-Tensiometer-PRODUCT

Wireless Line Riding Tensiometer and Rope Payout Sensor

Features

  • All stainless frame and hardware treated 4140 steel sheaves and fully sealed bearings.
  • Wire rope dimensions from 3/8” (9.5mm) to 4” (102mm) diameter
  • Single line capacity up to 450,000 lb (250 000 kg)
  • Load reading precision: +/-2% of rope capacity
  • Rope payout resolution: 1” (25.4 mm)
  • Optimized for crane or marine vessel applications; load and rope payout are transmitted up to four times per second.
  • Swing arm or permanent feet installation options
  • Radio range with line of sight: 4000 ft. (1300 m)
  • Operates with one ‘D’ cell battery lithium 3.6V or alkaline 1.5V.
  • 1 to 2 years battery life for typical applications
  • ISM license free radio: wavelength and modulation optimized for radio communication in industrial environments.
  • Temperature range: -40°C to 85°C (-40°F to 185°F)
  • Temperature compensated
  • Potted electronics for increased water protection

Trimble-GD0375-V2-Wireless-Line-Riding-Tensiometer- (1)

Applications

Measurement of wire rope tension (load) and/or rope payout with payout speed in all environments, including off shore.

 

Trimble-GD0375-V2-Wireless-Line-Riding-Tensiometer- (2)

Figure: Installation example on the main boom of a crane for the measurement of load and rope payout

 

Trimble-GD0375-V2-Wireless-Line-Riding-Tensiometer- (3)

General Description

The Line Riding Tensiometer operates by displacing a cable thru 3 sheaves and reading the bending force. In order to have a reliable load reading, the cable must contact all 3 sheaves in all operation positions. The payout sensor reads magnet encoders on the center sheave to compute a payout and speed value. Transmitter box mounted to the line riding tensiometer houses the battery, radio transmitter, load converter, and payout sensor.

Ordering Information

Model Description
GDXXXX-V2 Line Riding Tensiometer frame with appropriate sheaves for the wire rope. Thefour ‘X’ digits are the wire rope diameter in micro inches. For example, GD2500 – V2 is for a 2.5” diameter cable, GS1417 is for a 36mm cable.
GS007-01 Load only RF transmitter (902-928MHz)
GS007-CE-01GS007-0XM-CSA-V2 Load only RF transmitter (868-870 MHz)Load only RF transmitter (915MHz) frequency band with Class 1, Div 1 Certification
GS007-02 Load and Rope Payout/Speed RF Transmitter (902 -928MHz)
GS007-CE-02 Load and Rope Payout/Speed RF Transmitter (868 -870 MHz)
GD01X-V2 Appropriate swing arm for the frame size (see table page 6)
GD02X-V2 Appropriate feet kit for the frame size (see table page 6)

Specifications

Parameter Test Condition Min Typ Max Unit
Rope Tension Measurement
Resolution +/- 0.05 0.2 0.5 % of SWL
Accuracy +/- 1 2 6 % of SWL
Rope Movement Measurement
Payout Resolution (see page 6 for more precisevalues) +/- 0.5(12.7) 0.6(15) 1(25.4) in.(mm)
Radio Power
GDM-1125-FCC-V2 0.0054 W
7 dBm
Radio Frequency
North American version GS007 903 916 927 MHz
European version GS007-CE 868 868 870 MHz
Battery life
‘D’ cell battery lifedepends on usage 12 24 28 Month

Absolute Maximum Ratings

Parameter Test Condition Min Typ Max Unit
Temperature range Operating -40-40 +85+185 ºCºF

Certifications

  • FCC/IC/CE certification : FCC Part 15 Subpart C 15.247,15.205, 15.207 & 15.209
  • ETSI EN 300 220 (AA)
  • EMI/C – EN 61000-4-3, EN 301 489-1 – Clause 8.2
  • CSA Certificate Number – 80130757
  • CSA C22.2 No. 60079-0:19, 60079-11:14 (R2018), 61010-1-12, Update 1&2, Amd1:2018
  • UL 60079-0-2020, UL 60079-11-2018, UL 61010-1-2018
  • Class I, Division 1, Group A, B, C & D T4
  • Ex ia IIC T4 Ga
  • Class I, Zone 0, AEx ia IIC T4 Ga
  • Ambient Temperature: -20°C to 40°C.

WARNING: Only use Tadiran TL-5930 3.6V or Saft LS33600 cell 3.6V text.

Specifications by Model and Options

 Line Rider model Max load (lb) Max Load (kg) Payout resolution* (in) Payout resolution* (mm) Cable diameter (in) Weight lb [kg]  Load Only RF Transmitter Load and Rope Payout RFTransmitter  Swing Arm option  Feet Kit Option
GD0375-V2 4743 2156 0.57 14.46 3/8            GS007-01            GS007-02  GD012-V2  GD030-V2
GD0500-V2 8343 3792 0.53 13.47 ½ 29
GD0563-V2 10571 4805 0.51 12.97 9/16 [13]
GD0625-V2 12971 5896 0.49 12.47 5/8
GD0750-V2 18514 8416 0.75 18.95 ¾   62[28]   GD013-V2   GD030-V2
GD0875-V2 25029 11377 0.71 17.95 7/8
GD0945-V2 32514 14779 0.68 17.21 24mm
GD1000-V2 32514 14779 0.67 16.96 1
GD1125-V2 40857 18571 0.63 15.96 1 1/8
GD1250-V2 50229 22831 0.52 13.30 1 ¼   GD014-V2   GD031-V2
GD1375-V2 60571 27532 0.50 12.63 1 3/8 100
GD1417-V2 71429 32468 0.48 12.30 36mm [45.5]
GD1500-V2 71429 32468 0.47 11.97 1 ½
GD1625-V2 83429 37922 0.45 11.30 1 5/8
GD1750-V2 96571 43896 0.68 17.29 1 ¾  GD022-V2  GD031-V2
GD1890-V2 124000 56364 0.63 16.13 48mm 250
GD2000-V2 124000 56364 0.62 15.79 2 [113.5]
GD2250-V2 155429 70649 0.56 14.30 2 ¼
GD2500-V2 214857 97662 1.05 26.60 2 ½ 1010[459]  GD023-V2  GD032-V2
GD3000-V2 307429 139740 0.92 23.27 3
GD4000-V2 528571 240260 0.72 18.29 4

Do not use Payout data as a precise measurement.

Materials:
The frame, load sensing pin, and hardware are made of stainless steel (AISI 304 and 17-4PH1025), this includes the optional swing arm and brackets. The sheaves are in nitride 4140 steel and the bearings are integrally sealed from the environment.

Replacement parts

 Line Rider model  Cable Roller  Bearing  Seal
GD0375-V2/GD0500-V2/GD0563-V2/GD0625-V2 PF504 5205** CR 25x52x7 HMS5 RG
GD0750-V2/GD0875-V2/GD0945-V2/GD1000- V2/GD1125-V2 PF604 6205 CR 25x52x7 HMS5 RG
GD1250-V2/GD1375-V2/GD1417-V2/GD1500- V2/GD1625-V2 PF704 6207 CR 35x72x12 HMS5 RG
GD1750-V2/GD1890-V2/GD2000-V2/GD2250-V2 PF804 6210 CR 50x90x10 HMS5 RG
GD2500-V2/GD3000-V2/GD4000-V2 PF904 33113 CR 70x110x10 HMS5 RG
  • All bolting can be replaced with UNC nuts and bolts. Material is AISI 304 stainless steel or better.
  • Bearing number 4205 on models sold before 2012.

Dimensions

Trimble-GD0375-V2-Wireless-Line-Riding-Tensiometer- (4)

Trimble-GD0375-V2-Wireless-Line-Riding-Tensiometer- (5)

Units are in inches [millimeters] Alternative mounting holes for the swing arm + Secondary feet mounting holes

 Line Rider model D I M E N S I O N S  (inches)
   A    B    C    D    E    F    G Hadjustable in 6″ [152mm]increments    J    Z    Bolt
GD0375-V2 4.53 2.25 3.32 18.00 7.38 0.44 21.5 47.00-77.00 2.25 0.41 3/8-16
GD0500-V2 4.53 2.25 3.32 18.00 7.38 0.44 21.5 47.00-77.00 2.25 0.41 3/8-16
GD0563-V2 4.53 2.25 3.32 18.00 7.38 0.44 21.5 47.00-77.00 2.25 0.41 3/8-16
GD0625-V2 4.53 2.25 3.32 18.00 7.38 0.44 21.5 47.00-77.00 2.25 0.41 3/8-16
GD0750-V2 5.15 2.88 3.82 24.00 9.50 0.44 28.50 48.00-78.00 2.25 0.41 3/8-16
GD0875-V2 5.15 2.88 3.82 24.00 9.50 0.44 28.50 48.00-78.00 2.25 0.41 3/8-16
GD0945-V2 5.15 2.88 3.82 24.00 9.50 0.44 28.50 48.00-78.00 2.25 0.41 3/8-16
GD1000-V2 5.15 2.88 3.82 24.00 9.50 0.44 28.50 48.00-78.00 2.25 0.41 3/8-16
GD1125-V2 5.15 2.88 3.82 24.00 9.50 0.44 28.50 48.00-78.00 2.25 0.41 3/8-16
GD1250-V2 5.88 3.50 5.02 32.00 10.75 0.80 36.00 46.75-76.75 2.25 0.53 3/8-16
GD1375-V2 5.88 3.50 5.02 32.00 10.75 0.80 36.00 46.75-76.75 2.25 0.53 3/8-16
GD1417-V2 5.88 3.50 5.02 32.00 10.75 0.80 36.00 46.75-76.75 2.25 0.53 3/8-16
GD1500-V2 5.88 3.50 5.02 32.00 10.75 0.80 36.00 46.75-76.75 2.25 0.53 3/8-16
GD1625-V2 5.88 3.50 5.02 32.00 10.75 0.80 36.00 46.75-76.75 2.25 0.53 3/8-16
GD1750-V2 6.91 4.54 6.70 42.00 14.50 0.25 48.50 64.06-88.06 3.25 0.53 1/2-13
GD1890-V2 6.91 4.54 6.70 42.00 14.50 0.25 48.50 64.06-88.06 3.25 0.53 1/2-13
GD2000-V2 6.91 4.54 6.70 42.00 14.50 0.25 48.50 64.06-88.06 3.25 0.53 1/2-13
GD2250-V2 6.91 4.54 6.70 42.00 14.50 0.25 48.50 64.06-88.06 3.25 0.53 1/2-13
GD2500-V2 11.90 7.50 10.04 60.50 21.00 0.50 68.00 63.81-87.81 3.25 1.00 1/2-13
GD3000-V2 11.90 7.50 10.04 60.50 21.00 0.50 68.00 63.81-87.81 3.25 1.00 1/2-13
GD4000-V2 11.90 7.50 10.04 60.50 21.00 0.50 68.00 63.81-87.81 3.25 1.00 1/2-13
 Line Rider model D I M E N S I O N S  (mm)
   A    B    C    D    E    F    G Hadjustable in 6″ [152mm]increments    J    Z    Bolt
GD0375-V2 115.1 57.2 84.3 457.2 187.5 11.2 546.1 1194-1956 57.2 10.4 3/8-16
GD0500-V2 115.1 57.2 84.3 457.2 187.5 11.2 546.1 1194-1956 57.2 10.4 3/8-16
GD0563-V2 115.1 57.2 84.3 457.2 187.5 11.2 546.1 1194-1956 57.2 10.4 3/8-16
GD0625-V2 115.1 57.2 84.3 457.2 187.5 11.2 546.1 1194-1956 57.2 10.4 3/8-16
GD0750-V2 130.8 73.2 97.0 609.6 241.3 11.2 723.9 1219-1981 57.2 10.4 3/8-16
GD0875-V2 130.8 73.2 97.0 609.6 241.3 11.2 723.9 1219-1981 57.2 10.4 3/8-16
GD0945-V2 130.8 73.2 97.0 609.6 241.3 11.2 723.9 1219-1981 57.2 10.4 3/8-16
GD1000-V2 130.8 73.2 97.0 609.6 241.3 11.2 723.9 1219-1981 57.2 10.4 3/8-16
GD1125-V2 130.8 73.2 97.0 609.6 241.3 11.2 723.9 1219-1981 57.2 10.4 3/8-16
GD1250-V2 149.4 88.9 127.5 812.8 273.1 20.3 914.4 1187-1949 57.2 13.5 3/8-16
GD1375-V2 149.4 88.9 127.5 812.8 273.1 20.3 914.4 1187-1949 57.2 13.5 3/8-16
GD1417-V2 149.4 88.9 127.5 812.8 273.1 20.3 914.4 1187-1949 57.2 13.5 3/8-16
GD1500-V2 149.4 88.9 127.5 812.8 273.1 20.3 914.4 1187-1949 57.2 13.5 3/8-16
GD1625-V2 149.4 88.9 127.5 812.8 273.1 20.3 914.4 1187-1949 57.2 13.5 3/8-16
GD1750-V2 175.5 115.3 170.2 1066.8 368.3 6.4 1231.9 1627-2237 82.6 13.5 1/2-13
GD1890-V2 175.5 115.3 170.2 1066.8 368.3 6.4 1231.9 1627-2237 82.6 13.5 1/2-13
GD2000-V2 175.5 115.3 170.2 1066.8 368.3 6.4 1231.9 1627-2237 82.6 13.5 1/2-13
GD2250-V2 175.5 115.3 170.2 1066.8 368.3 6.4 1231.9 1627-2237 82.6 13.5 1/2-13
GD2500-V2 302.3 190.5 255.0 1536.7 533.4 12.7 1727.2 1621-2330 82.6 25.4 1/2-13
GD3000-V2 302.3 190.5 255.0 1536.7 533.4 12.7 1727.2 1621-2330 82.6 25.4 1/2-13
GD4000-V2 302.3 190.5 255.0 1536.7 533.4 12.7 1727.2 1621-2330 82.6 25.4 1/2-13
  • PMN: GDM-1125-FCC-V2
  • HVIN: MB103-00-SD-A

FCC Compliance Statement (USA)

FCC ID: S9E-GS200G
Compliance Statements: This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including, an interference that may cause undesired operation.

Caution Statements:

  • Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
  • This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

Industry Canada (IC) Compliance Statement

IC: 5817A-GS000G

Compliance Statements: This device complies with Industry Canada license-exempt RSS standard(s).

Caution Statements:

  • This equipment complies with radio frequency exposure limits set forth by Industry Cananda for an uncontrolled environment.
  • This equipment should be installed and operated with a minimum distance of 20 cm between the device and the user or bystanders.

Information to the User

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Frequently Asked Questions

  • Q: What wire rope dimensions are suitable for this product?
    A: Wire rope dimensions ranging from 3/8″ to 4″ in diameter are suitable for this Line Riding Tensiometer.
  • Q: What is the battery life of the transmitter box?
    A: The battery life of the transmitter box ranges from 12 to 28 months depending on usage.

Documents / Resources

Trimble GD0375-V2 Wireless Line Riding Tensiometer [pdf] Owner's Manual
GS200G, S9E-GS200G, S9EGS200G, GD0375-V2 Wireless Line Riding Tensiometer, GD0375-V2, Wireless Line Riding Tensiometer, Line Riding Tensiometer, Riding Tensiometer, Tensiometer

References

Leave a comment

Your email address will not be published. Required fields are marked *