TRIGGR Striker Wireless Gaming Controller User Manual

TRIGGR-Striker-logo

TRIGGR Striker Wireless Gaming Controller

TRIGGR-Striker-Wireless-Gaming-Controller-product

USER MANUALTRIGGR-Striker-Wireless-Gaming-Controller  (2)

PRODUCT SPECIFICATIONS

  • Frequency Range: 2.402-2.480 GHz
  • Bluetooth Protocol: BT2.1+EDR
  • Battery Specification: 3.7V/600mAh
  • Operating Voltage: 3.7V-4.2V
  • Working Distance: 10M
  • Polling Rate: 1000Hz
  • Working Platforms: PC, Switch, Steam Deck, iPhone, iPad, Android, PS3, PS4
  • Input: 5V/200mA-300mA
  • Charging Time: about 3 hours
  • Playing time: Up To 10* Hrs
  • Connection Mode: Wired / Wireless / Dongle
  • Dimensions: 155x105x65mm
  • Working Mode: PC-X-Input/D-Input, PS3, PS4, Android HID, iOS MFI

IN THE BOX

TRIGGR-Striker-Wireless-Gaming-Controller  (3)

MODES AND PLATFORMS

The One S supports the following Modes and each Mode supports the following Platforms respectively.

TRIGGR-Striker-Wireless-Gaming-Controller  (4)

SWITCH (BLUETOOTH)

  1. Press and hold the [Home+Y] keys to enter pairing mode (The Home key’s LED will blink).
  2. Double-click the [Controller] icon on the host, then click [Change Grip/Order] again.
  3. Pairing successful (The controller will vibrate and blue LED always-on upon successful pairing).

TRIGGR-Striker-Wireless-Gaming-Controller  (5)

STEAM DECK (BLUETOOTH)Dinput Mode:

  1. Press and hold the [Home + X] keys to enter pairing mode (The Home key will light up red).
  2. Turn on your computer’s Bluetooth and go to Bluetooth settings.
  3. Connect to the device “TRIGGR Striker” (white LED always-on once paired successfully).

Xinput Mode:

  1. Press and hold the [Home + B] keys to enter pairing mode (The Home key will light up yellow).
  2. Turn on your computer’s Bluetooth and go to Bluetooth settings.
  3. Connect to the device “Xbox ONE Wireless Controller” (Blue LED always-on once paired successfully).

TRIGGR-Striker-Wireless-Gaming-Controller  (6)

USB DONGLE CONNECTION

  • Plug the receiver into your device’s USB port.
  • On the Controller, press and hold the [Home + A] keys to enter pairing mode (The Home key LED will blink).
  • Hold the receiver’s pairing button for 3 seconds — its blue LED flashes rapidly to enter pairing mode with the controller.
  • Turn on your computer’s Bluetooth and go to Bluetooth settings.
  • Connect to the device “Xbox 360 Controller for Windows“.
  • Successful pairing: Receiver blue LED always-on; controller white LED always-on.

Timeout Rules:

  • Failed pairing: Controller auto-sleeps after 60 seconds.
  • Paired but idle: Controller auto-sleeps after 5 minutes of inactivity.
  • Default mode: X-INPUT. Hold the View / Menu buttons together for 3 seconds to switch between D-INPUT (Bluetooth Name: Gamepad) and NS modes (Bluetooth Name: Pro Controller).

TRIGGR-Striker-Wireless-Gaming-Controller  (7)

BLUETOOTH WINDOWS

  1. Press and hold the [Home + B] keys to enter pairing mode (The Home key will light up yellow).
  2. Turn on your computer’s Bluetooth and go to Bluetooth settings.
  3. Connect to the device “Xbox Wireless Controller” (Blue LED always-on once paired successfully).

TRIGGR-Striker-Wireless-Gaming-Controller  (8)

iOS (BLUETOOTH)

  1. Press and hold the [Home + B] keys to enter pairing mode (The Home key will light up yellow).
  2. Turn on your phone’s Bluetooth and go to Bluetooth settings.
  3. Connect to the device “XBOX WIRELESS CONTROLLER” (The controller will vibrate and blue LED always-on once paired successfully).

TRIGGR-Striker-Wireless-Gaming-Controller  (9)

ANDROID (BLUETOOTH)

  1. Press and hold the [Home + X] keys to enter pairing mode (The Home key will light up red).
  2. Turn on your phone’s Bluetooth and go to Bluetooth settings.
  3. Connect to the device “TRIGGR Striker” (The controller will vibrate and blue LED always-on once paired successfully).

TRIGGR-Striker-Wireless-Gaming-Controller  (10)

PS4 CONNECTION

  1. Plug the USB cable to a PS4 console.
  2. Press the HOME button.
  3. Unplug the cable for wireless reconnection.
  4. Blue LED stays always-on once paired successfully.

Note: In game, the screenshot button functions the same as the touchpad.

PS3 MODE

  1. Plug the USB cable to a PS3 console.
  2. Press the HOME button.
  3. Unplug the cable for wireless reconnection.
  4. Blue LED stays always-on once paired successfully.

TRIGGR-Striker-Wireless-Gaming-Controller  (11)

USB WIRED CONNECTION – PC X-INPUT / PS3 / PS4 / SWITCH

  1. Connect the device and the controller using a Type-C cable (the controller will vibrate to indicate successful pairing).
  2. Note for PC wired connection: It defaults to Xinput mode (Bluetooth Name: Xbox 360 Controller). Press and hold the “View” and “Menu” buttons for 3 seconds to switch between Xinput (Blue light) and Dinput mode (Red light) (Bluetooth Name: Gamepad).
  3. Note for Android: Android devices support both Xinput (Blue light) and Dinput mode (Red light).

WAKEPress and hold the Home key for 1 second to wake the controller. Paired controllers will auto-connect.

Note: 1. Vibrates on success. 2. Supported services: PS3, PS4, Switch, Android, iOS.

SLEEP

  1. The controller enters sleep mode automatically when the Switch console sleeps.
  2. When connected: The controller sleeps after 5 minutes of inactivity.
  3. Manual Sleep: When connected, press and hold the Home key for 3 seconds to manually enter sleep mode.

FUNCTION SETTINGSTURBO SETTINGS

Press the TURBO button + any of the following keys to set the Turbo function: A / B / X / Y / LB / RB / LT / RT / D-Pad

  • First Press (TURBO + Button): Manual TURBO (Hold the button to fire continuously).
  • Second Press (TURBO + Button): Auto TURBO (Fires continuously automatically without holding the button).
  • Third Press (TURBO + Button): Turn off TURBO for this specific button.

Note: Hold the TURBO button for 5 seconds to clear all TURBO settings. If vibration is enabled, the controller will vibrate as a confirmation prompt.

TRIGGR-Striker-Wireless-Gaming-Controller  (13)

VIBRATION SETTINGSPress the Vibration Key to adjust vibration intensity (confirmed via vibration feedback).
Vibration intensity cycles through: 100% > 75% > 50% > 30% > 0%.
Note: Supports power-off memory function.

TRIGGR-Striker-Wireless-Gaming-Controller  (14)

STICK DEADZONE CALIBRATIONPress the Calibration Key to set the stick deadzone range (confirmed via vibration feedback).

Deadzone range cycles through: 0° > 2° > 4° > 6°.
Note: Supports power-off memory function.

TRIGGR-Striker-Wireless-Gaming-Controller  (1)

STICK AND TRIGGER CALIBRATION

  1. With the controller powered off, press the “View” + “Home” + “B” buttons simultaneously to enter calibration mode.
  2. Rotate both joysticks fully 2 to 3 times, and press LT/RT fully 2 to 3 times.
  3. Press the View and Menu keys to exit calibration.

INDICATOR (HOME BUTTON)

  • Charging while powered off: Home button blue light flashes slowly; turns off when fully charged.
  • Charging while playing: Home button red light flashes slowly; red light stays solid when fully charged.
  • Low battery alert: Home button red light flashes rapidly.

LED SETTINGHold Turbo + single-click right joystick to switch the ABXY light modes: Steady On / Off.

MACRO PROGRAMMABLE FUNCTION (ML/MR)Macro Sequence Recording

  • Press the ML/MR button -> the HOME LED turns red.
  • Input your desired key combination (up to 20 steps).
  • Press ML/MR again to finish recording (vibration feedback).
  • Editable keys for macros: A, B, X, Y, LT, RT, LB, RB, R/L Joystick, View, Menu, D-pad. Perfect for in-game combo moves.

Macro Mapping Function

  • Press the Right ML/MR button -> the HOME LED turns red.
  • Input the single key you want to map.
  • Press ML/MR again to finish recording (vibration feedback).
  • All Programmable & Mapping settings include a memory function that retains settings even when powered off.
  • Double-click ML/MR to clear macro functions (vibration feedback).

RESETUse a pin to press the physical reset key to force-restart the device if it becomes frozen or unresponsive.

CUSTOMER CARE

Creovaive Ventures Pvt. Ltd. Address: Building no. 55, Block-B, Sector-4, Noida, U.P – 201301 Email: care@gettrigr.com Tel: +91 8851340679 Web: www.gettrigr.com

This product is not designed, manufactured, sponsored, or endorsed by Nintendo. All other trademarks are the properties of their respective owners.

“Nintendo”, “SWITCH”, and their logos are trademarks of Nintendo of America Inc. “Playstation” and its logo are trademarks of Sony Entertainment America Inc. “ANDROID” and its logo are trademarks of GOOGLE LLC. “iOS” is a trademark of Cisco in the U.S. USB Type-C and USB-C are registered trademarks of USB Implementers Forum. The Bluetooth word mark and logos are trademarks owned by the Bluetooth SIG, Inc. All trademarks are the property of their respective owners. These owners did not design, manufacture, sponsor, or endorse this product.

MATTERS NEEDING ATTENTION

  • Do not leave the device unattended while charging to avoid overcharging.
  • Avoid exposing the controller to high temperatures, humidity, or direct sunlight.
  • Do not disassemble, drop, or squeeze the controller to prevent internal damage.
  • Keep the controller away from water or liquids to prevent short circuits or damage.
  • Charge the controller periodically during long periods of inactivity to protect the battery.
  • Do not store the controller with sharp objects to avoid surface scratches.
  • Stop using and contact support immediately if the controller overheats, smokes, or emits unusual odors.
  • Do not allow children to use the controller unsupervised to prevent choking hazards or other risks.
  • Read the manual carefully before use to ensure proper operation.

Documents / Resources

PDF thumbnailStriker Wireless Gaming Controller
User Manual · TRIGGR, Striker, Controller, Gaming

References

Ask a Question

Use this section to ask about setup, compatibility, troubleshooting, or anything missing from this manual.

Ask a Question

Ask about setup, compatibility, troubleshooting, or anything missing from this manual. Name and email are optional.