Trantec S5000 Beltpack Transmitter Microphone
Specifications
- Model: Trantec S5000
- Frequency Channels: 6 (UK license-free channel 70)
- Operating Frequencies: 863.100, 863.400, 863.750, 864.225, 864.550, 864.975 MHz
- Audio Output Connector: 5-pin Lemo connector (FGG series)
Product Usage Instructions
Receiver (Trantec S5000 eng receiver):
- Connect the receiver to a power source.
- Tune the receiver to one of the 6 available frequency channels (863.100, 863.400, 863.750, 864.225, 864.550, 864.975 MHz).
- Ensure proper audio output connection using the 5-pin Lemo connector.
Trantec S5000 eng receiver
Press button under battery door functions:
- Bank – change bank 1 to 4 using the encoder on the top of the pack
- Freq – change the frequency using the encoder on the top of the pack
- Gain – change the audio level gain using the encoder on the top of the pack
- Rf cue – change the squelch level
- Always return to the Freq menu then power down to save settings – then reboot.
- The following 6 frequency are uk license free channel 70
All 6 will operate together
- 863.100
- 863.400
- 863.750
- 864.225
- 864.550
- 864.975
These are the first 6 frequencies of bank 1
Audio output is on a 5 pin lemo connector fgg series Ob
Image is of the solder view of the male connector which plugs into the s5000 eng receiver pack
- PIN 1 – Ground
- Pin 2 audio + output
- Pin 3 Ground
- Pin 4 power from camera external battery 10 v to 18v
- Pin 5 audio – output
Trantec S5000 beltpack radio mic transmitter
- Press button under battery door functions:
- Press and hold on power upp – reset (some models only)
- Press to cycles through the banks 1 to 4 (if programmed) then power down to save settings – then reboot.
Pin Connections : Pin 1 Ground, Pin 2 +9v, Pin 3 Audio/+9v, Pin 4 Audio
| Trantec TS259: | Trantec TS33: | Trantec TS44: |
| Pin 1 Screen | Pin 1 Screen | Pin 1 Screen |
| Pin 2 Not connected | Pin 2 Not Connected | Pin 2 Red |
| Pin 3 White | Pin 3 White and Red | Pin 3 Not Connected |
| Pin 4 Not Connected | Pin 4 Not Connected | Pin 4 White |
| Trantec TS55: | Trantec TS912: | Sennheiser MKE2: |
| Pin 1 Screen | Pin1 Screen | Pin 1 Screen |
| Pin 2 Red | Pin 2 Red | Pin 2 Not connected |
| Pin 3 Not Connected | Pin 3 Not Connected | Pin 3 Red |
| Pin 4 White | Pin 4 Yellow | Pin 4 Not Connected |
| Sony ECM77: | Sanken COS-11PT: | Beyer MCE5: |
| Pin 1 Screen plus Clear | Pin 1 Screen | Pin 1 Screen |
| Pin 2 Not Connected | Pin 2 Black | Pin 2 Red |
| Pin 3 Red | Pin 3 Not Connected | Pin 3 Not Connected |
Frequently Asked Questions
- Q: Can I use multiple Trantec S5000 beltpack radio mic transmitters with one receiver?
A: Yes, all 6 frequencies of the Trantec S5000 eng receiver can operate together, allowing you to use multiple beltpack transmitters simultaneously.
Documents / Resources
 |
Trantec S5000 Beltpack Transmitter Microphone [pdf] Instructions TS259, TS33, TS44, TS55, TS912, S5000 Beltpack Transmitter Microphone, S5000, Beltpack Transmitter Microphone, Transmitter Microphone, Microphone |
