JetWave RC3000 Remote Controller User Manual

JetWave RC3000 Remote Controller

Özellikler

The JetWave Remote Controller features a touch screen, intercom button, gear down button, audio speaker, microphone, OK/Power button, gear up button, wristband, NFC magnetic charging port, trigger, and lanyard hole.

• Görüntülemek: Dokunmatik Ekran
• Bağlantı: NFC, Wireless (for board pairing)
• Güç: Rechargeable via Magnetic Charging Port
• Kontroller: Intercom, Gear Up/Down, OK/Power, Trigger
• Ses: Hoparlör, Mikrofon
• giyilebilirlik: Wristband, Lanyard Hole

Ürün bileşeni adı

Uzaktan Kumanda

Bağlantı ve Eşleştirme

Uzaktan Kumanda Eşleştirme
Press and hold the power button on the remote control for 3 seconds, to poweron. Connect the paired Board according to the prompt.

• Press Power Button 3s (vibrates on)
•  Select “Search Pairing”
• Waiting for search

When it is turned on for the first time, the board will be automatically activated after the battery is installed (please ensure a network connection). Check whether the network of the remote control is normal. Only when the network is normal can the board be successfully activated

• Choose Board from list
• Connected and paired

Cihaz Yükseltme

JetWave devices support OTA upgrades. We highly recommend regularly checking for firmware upgrades and updating to the latest version for a better user experience. Refer to P41 for details.

Initial Device Binding

For board owners, it is recommended to scan the QR code with the App to bind the device in order to enjoy more services, such as remotely accessing device session records, setting safety zones, and activating product warranty periods.

1. Open the QR code on the remote control when successfully connected to the board.
   • Swipe down to pop up the Remote Controller Settings
   • "Hakkında"ya tıklayın
   • Click “Bind ID”
   • Show QR code.
2. In the app, tap “+” on the Device page, Scan QR code.
3. After successful binding, the APP device interface will display the bound device information; the controller will display the bound ID information.

• Warranty period varies by region and usage. Additional warranty benefits beyond standard coverage are only available to the original owner after binding. See JetWave webGaranti koşullarının tamamı için site.

Operasyon Rehberi

User Login (Optional)

Login Method 1: Open the “Login” interface on the remote control and log in by scanning the code with the APP.

• Swipe up to access login screen
• In APP, go to Personal Center and tap scan icon

Login Method 2: Enter the JetWave ID and password on the remote control screen to complete the login.

• Get your JetWave ID/password from APP Personal Center > Avatar > Personal Information.
• Riders can view sessions on devices they log into.
• Device owners can view all records for their devices.

Mode Selection & Gear Setting

Choose between three control modes (Beginner/Sport/Wild) based on your skill level.

• Each mode has different gear settings that you can adjust as needed.

Yolculuğunuzu Sonlandırma

• Hold the power button for 3 seconds to end your ride and sync data to the app.

• To power off, hold until the shutdown screen appears, then slide to confirm.
• For a force shutdown, hold for 10 seconds.
• View Session Log in app (Personal Center → Ride History).

Not: Session records are only valid when logged in before riding.

Gelişmiş İşlemler

Yazılım Yükseltmesi

1. Power on remote control,ensure connection to board and online.
2. Swipe down and select firmware upgrade option.
3. Review current versions. Click “Firmware Upgrade” to update all modules with “NEW” status.
4. For system upgrade, swipe left and click “Upgrade Now”.
5. Click “Check Version” to upgrade automatically. Remote will restart after upgrade.

• The remote control battery must be above 50% before upgrading.

Remote Control Re-Pairing

If the remote control loses connection or is replaced, you’ll need to pair it with the surfboard.

1. Power on the board with the battery installed.
2. Turn on the remote control, click search, find the board’s Bluetooth signal, and select it to connect.

Uzaktan Kumanda Kalibrasyonu

1. Power on remote control in end-of-session state
2. Go to Settings → Remote Control Calibration
3. Follow prompts to calibrate throttle trigger by fully pressing and releasing multiple times

Remote Control Network Status Checking

Network must available at first power-on for successful board activation.

1. Power on remote control, swipe down for settings.
2. Go to System Parameters → Network Settings.
3. Check network status – contact support if not normal.

• JetWave provides 2 years of free 4G data. After expiry, users should renew their subscription or use a WiFi hotspot.

Teknik Özellikler

Uyumluluk Bilgileri

FCC Beyanı
This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved could void the user’s authority to operate the equipment.

SAR Bilgileri

This Smart Controller meets government requirements for radio wave exposure. The FCC SAR limit is 1.6 W/kg averaged over one gram of tissue.

FCC KİMLİĞİ: 2BQTS-RC3000
Highest reported SAR value: 1.331 W/kg (body-worn)
This device was tested for body-worn operation with the back of the device kept 0 mm from the body. To maintain FCC RF exposure compliance:

• Use accessories that keep a 0 mm separation between the body and the back of the device.
• Belt clips, holsters, and similar accessories must not contain metal components.
• Avoid using accessories that do not meet these requirements.

Vücuda Takılan Operasyon
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 0 mm must be maintained between the user’s body and the device, including the antenna.

• Bu cihazla birlikte kullanılan üçüncü taraf kemer klipsleri, kılıflar ve benzeri aksesuarlar hiçbir metalik bileşen içermemelidir.
• Bu gereksinimleri karşılamayan vücuda takılan aksesuarlar RF'ye maruz kalma gereksinimlerine uymayabilir ve bunlardan kaçınılmalıdır.
• Yalnızca verilen anteni veya onaylı anteni kullanın.

FCC BEYANI

Not: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measure s:

• Alıcı anteni yeniden yönlendirin veya yerini değiştirin.
• Ekipman ile alıcı arasındaki mesafeyi artırın.
• Ekipmanı, alıcının bağlı olduğu devreden farklı bir devre üzerindeki prize bağlayın.
• Yardım için satıcınıza veya deneyimli bir radyo/TV teknisyenine danışın.

Sorun giderme

• Remote not powering on: Ensure the remote is charged. Connect it to the magnetic charging port.
• Remote not pairing with the board:
  • Ensure the board battery is inserted and the lid is closed.
  • Check if the remote control has a normal network connection.
  • Try restarting both the remote and the board.
  • Ensure both devices are within range.
• App not binding to the device:
  • Ensure the remote is successfully connected to the board.
  • Check your app’s internet connection.
  • Ensure you are scanning the correct QR code (from “Bind ID” on the remote).
• Cannot log in:
  • Verify your JetWave ID and password.
  • Check your remote’s network connection.
  • If using app scan, ensure the app is connected to the internet.
• Session records not appearing in app: Ensure you were logged into your account on the remote control before starting your ride.