tp-link UH7021C USB Type C 7 In 1 Hub Installation Guide

This hub supports the Plug and Play feature. Follow these steps to connect the hub to your host device:
Plug the USB-C connector into your host device.

Plug your external peripheral into the corresponding port of the hub.
When using external peripherals with the hub, follow these guidelines:

Ensure the hub is securely connected to your host device.
If you need to use a PD charger, make sure it meets the input specifications of the USB-C PD port.

When not in use, unplug or remove external peripherals from the hub before disconnecting the hub from your host device.
Understand that the USB-C PD port is for charging only and does not support data transfer.

Use an original or certified PD charger that meets the input specifications of the USB-C PD port.

Product Overview

(1)USB-C Connector	For connecting to your host device.
(2) USB-C PD (Power Delivery) Port*	For unidirectionally charging your host device when connected to a PD charger. PD 3.0; Up to 100W * Does not support data transfer.
(3)USB-A Port (7)USB-A Port ×2	USB 3.0; Up to 5 Gbps data transfer
(4)HDMI® Port	Up to 4K@60Hz (backward compatible)
(5)TF (microSD) Card Slot (6) SD Card Slot	SD 3.0; UHS-I; Up to 200MB/s; Supports simultaneously reading and writing two cards

Input	PD: 5V/3A, 9V/3A, 12V/3A, 15V/3A, 20V/5A USB-C Connector: 5V/3A
Supported Systems	Windows, macOS, iPadOS, iOS, ChromeOS, Linux, Android
Plug and Play	USB-C PD port, HDMI® port, TF (microSD) card slot, SD card slot, USB-A ports.

Note: The ports’ actual performance may vary based on your host device specifications.

Using the Hub

This hub supports the Plug and Play feature.
Plug the USB-C connector into your host device, then plug in your external peripheral into the corresponding port of the hub.

Note: A PD charger (not included) is not required. If you wish to use a PD charger to charge your host device, please refer to Tips (2B).

Tips

When not in use, please unplug or remove the external peripherals from the hub first, and then unplug the hub from your host device.

If you need to connect a PD charger to the hub’s USB-C PD port, please:
- A) Notice that it only has the charging function and is input-only.
- B) Use an original or certified PD charger to charge your host device. The output of the PD charger should meet the input specifications of the USB-C PD port.

The terms HDMI, HDMI High-Definition Multimedia Interface, HDMI trade dress and the HDMI Logos are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2011/65/EU, 2009/125/EC and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/support/ce/
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of the Electromagnetic Compatibility Regulations 2016.
The original UK declaration of conformity may be found at https://www.tp-link.com/support/ukca/

Safety Information

When the product has a power button, the power button is one of the ways to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Keep the device away from water, fire, humidity, or hot environments.
This equipment can be powered only by equipments that complies with Power Source Class 2 (PS2) or Limited Power Source (LPS) defined in the standard of IEC 62368-1.

Operating Temperature: 0°C~40°C (32°F~104°F),
Storage Temperature: -40°C~60°C (-40°F ~140°F)

FCC Statement

FCC Compliance Information Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
We, TP-Link Systems Inc., have determined that the equipment shown above has been shown to comply with the applicable technical standards, FCC part 15. There are no unauthorized changes made in the equipment, and the equipment is properly maintained and operated.

Explanation of the symbols on the product label
The equipment marking is at the bottom of the device. Symbols may vary from product.

Indoor use only
DC voltage
AC voltage

RECYCLING
This product bears the selective sorting symbol for Waste Electrical and Electronic Equipment (WEEE). This means that this product must be handled pursuant to European Directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. The user has the choice to give his product to a competent recycling organization or to the retailer when he buys new electrical or electronic equipment.
Energy efficiency marking (level VI)
Polarity of output terminals

Class II equipment
Caution
Operator’s manual

CONTACT

Product Name: USB Type-C 7-in-1 Hub
Model Number: UH7021C
Responsible party:

TP-Link Systems Inc.
Address: 10 Mauchly, Irvine, CA 92618
Website: http://www.tp-link.com/us/

Tel: +1 626 333 0234
Fax: +1 909 527 6804
E-mail: sales.usa@tp-link.com

FAQ

Q: Can I use this hub with any host device?
- A: The hub is compatible with Windows, macOS, iPadOS, iOS, ChromeOS, Linux, and Android systems. However, actual performance may vary based on your host device specifications.
Q: Do I need a PD charger to use this hub?
- A: The hub supports Plug and Play functionality without requiring a PD charger. However, if you wish to charge your host device using a PD charger, please ensure it meets the necessary specifications.

Documents / Resources

tp-link UH7021C USB Type C 7 In 1 Hub [pdf] Installation Guide
UH7021C, UH7021C USB Type C 7 In 1 Hub, UH7021C, USB Type C 7 In 1 Hub, 7 In 1 Hub, Hub

References

User Manual

tp-link UH7021C USB Type C 7 In 1 Hub

Specifications

Product Usage Instructions