How do I connect a second CPE710 as a repeater to an existing CPE710 SSID?
Answer
To connect a second CPE710 as a repeater (Client or Bridge mode) to your primary CPE710, please follow these steps within the PharOS web interface:
Check Operation Mode: Ensure the primary CPE710 is set to Access Point mode and the second unit is set to Client or Bridge mode. The CPE710 does not have a dedicated 'Repeater' mode in the traditional sense; 'Bridge' mode is typically used for this purpose.
Alignment: Since the CPE710 is a highly directional 23dBi antenna, the units must be precisely pointed at each other. Even a slight misalignment can prevent a successful connection.
Frequency Settings: Ensure both devices are using the same Channel Width (e.g., 20/40/80MHz). If the primary unit is set to a specific frequency, the secondary unit must be able to scan and find that frequency.
Security Match: The WPA2/PSK password and encryption type on the secondary unit must exactly match the settings on the primary Access Point.
IP Address Conflict: Ensure both units have unique static IP addresses on the same subnet (e.g., 192.168.0.254 and 192.168.0.253) so you can manage them independently.
If you still cannot connect, try performing a Survey on the secondary unit's Wireless settings page to see if the primary SSID appears in the list of available networks.
Is it possible to use the TP-Link CPE series antennas to view monitoring data from NEC monitoring devices (CSDX or CSDJ) on a PC?
Answer
Yes, it is generally possible to use the TP-Link CPE710 (or other CPE series devices) to transmit data from NEC monitoring devices like the CSDX or CSDJ to a PC, provided both devices support standard Ethernet/IP networking.
The CPE710 acts as a high-speed wireless bridge. To achieve this, you would typically follow these steps:
Network Connection: Connect the NEC monitoring device to one CPE unit (configured as an Access Point) and the PC (or the network the PC is on) to a second CPE unit (configured as a Client).
Transparent Bridge: The CPE series creates a transparent Layer 2 bridge, meaning the NEC device and the PC will behave as if they are connected by a physical Ethernet cable.
IP Configuration: Ensure that the NEC device, the CPE units, and the PC are all within the same IP subnet so they can communicate.
Software: You will still need the specific NEC monitoring software installed on your PC to view the data; the CPE units only provide the wireless link.
Note: Since the CPE710 is a highly directional 5GHz antenna, a clear line-of-sight between the two antennas is required for a stable connection.
CPE710のSSIDで別のCPE710を中継機として使いたいのですがうまく接続できません。
How do I connect a second CPE710 as a repeater to an existing CPE710 SSID?
To connect a second CPE710 as a repeater (Client or Bridge mode) to your primary CPE710, please follow these steps within the PharOS web interface:
If you still cannot connect, try performing a Survey on the secondary unit's Wireless settings page to see if the primary SSID appears in the list of available networks.
Read the full Q&A page
CPEシリーズアンテナを利用して、NEC製監視装置CSDX(またはCSDJ)の監視をPCにて閲覧することは可能でしょうか。
Is it possible to use the TP-Link CPE series antennas to view monitoring data from NEC monitoring devices (CSDX or CSDJ) on a PC?
Yes, it is generally possible to use the TP-Link CPE710 (or other CPE series devices) to transmit data from NEC monitoring devices like the CSDX or CSDJ to a PC, provided both devices support standard Ethernet/IP networking.
The CPE710 acts as a high-speed wireless bridge. To achieve this, you would typically follow these steps:
Note: Since the CPE710 is a highly directional 5GHz antenna, a clear line-of-sight between the two antennas is required for a stable connection.
Read the full Q&A page