TP-Link Tapo S310D Scene Controller Mate Switch

Specifications

• Equipment Name: Tapo S310D
• Type Designation: Type
• Unit: PCB
• Lead (Pb): –
• Restricted Substances and Chemical Symbols:
  • Mercury (Hg): 0.1 wt% % (Note 1)
  • Cadmium (Cd): 0.01wt%t % (Note 1)
  • Hexavalent Chromium (Cr+6): Exceeding 0.wt%wt % (Note 1)
  • Polybrominated Biphenyls (PBB): Exceeding 0 wt% wt % (Note 1)
  • Polybrominated Diphenyl Ethers (PBDE): – (Note 3)

Product Usage Instructions

Authentication
Ensure the device is compliant with FCC regulations and adheres to the Canadian Compliance Statement for proper operation.

Radiation Exposure Statement
This equipment complies with IC radiation exposure limits. Maintain a minimum distance of 20cm between the device and your body during installation and operation.

Safety Information

Refer to the symbols on the product label for important safety instructions. Symbols may vary but typically indicate information such as dangerous voltage, risk of electric shock, and energy efficiency marking.

Authentication

FCC compliance information statement

• Product Name: Scene Controller Mate Switch
• Model Number: Tapo S310D
• Responsible party:
• TP-Link Systems Inc.
• Address: 10 Mauchly, Irvine, CA 92618
• Website: http://www.tp-link.com/us/
• Tel: +1 626 333 0234
• Fax: +1 909 527 6804
• E-mail: sales.usa@tp-link.com

This equipment has been tested and found to comply with the limits for a Class B digital device under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedbyh the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement
This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant applies to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”

We, TP-Link Systems Inc., have determined that the equipment shown above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized changes have been made to the equipment, and the equipment is properly maintained and operated.

Canadian Compliance Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)

NCC Notice

BSMI Notice

Equipment name				： Tapo S310D Type designation (Type)
Unit   PCB				Restricted all symbols substances and their chemical
	Lead (P○b)	Mercury (H○g)	Cadmium (C○d)	Hexavalent +c6hromium (C○r  )	Polybrominated biphenyls (P○BB)	(PB○DE)
	○	○	○	○	○	○
	−	○	○	○	○	○
	−	○	○	○	○	○

• Note 1： “Exceeding 0.1 wt% %” and “exceeding 0.01wt%t wt%” indicate that the percentage content of the restricted substance exceeds the reference percentage value of the presence condition.
• Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of the reference value of presence.
• Note 3：The “−” indicates that the restricted substance corresponds to the exemption.

Safety Information

Before installing, servicing, or removing the switch, read and follow all safety precautions, including the following:

• Follow all national and local safety regulations and practices. If you are uncertain or uncomfortable when performing the installation, consult a qualified electrician.
• CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment and luminaire before servicing. A circuit breaker which disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off.
• Do not install the Smart Switch with wet hands or when standing on wet surfaces.
• Keep the device away from water, fire, humidity, or hot environments.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Do not use the device where wireless devices are not allowed.
• Rating: 120 V~ 60 Hz
• Supported Load: Connect up to 20 Tapo L730.
• Operation temperature: -10~40°C /14~104°F
• Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).

Explanation of the symbols on the product label

Note: The product label is on the bottom of the product and its power supply. Symbols may vary from product.

Symbol	Explanation
m	Switch to mini-gap construction
µ	Switch of micro-gap construction (for US version) Switch of micro-gap / micro-disconnection construction (for other versions except US)
ε	Switch without contact gap (Semiconductor switching device)

FAQS

• Q: What should I do if the device does not power on?
  A: Check the power plug connection and ensure there is a stable power source. If the issue persists, contact customer support for further assistance.
• Q: How can I reset the device to factory settings?
  A: Locate the reset button on the device, usually found near the power port. Use a small tool to press and hold the button for atleast 10 seconds until the device resets.

Documents / Resources

tp-link Tapo S310D Scene Controller Mate Switch [pdf] Owner's Manual 2BH7FS310D, s310d, Tapo S310D Scene Controller Mate Switch, Tapo S310D, Scene Controller Mate Switch, Controller Mate Switch, Mate Switch, Switch

References

• User Manual