tp-link Enlarge Your Ethernet Network -logo

Enlarge Your Ethernet Network
10/100 Mbps WDM Media Converter

Package Contents: Converter, Power Adapter, Installation Guide

LED Explanation
Ο PWR
On: Power on
Off: Power off

Ο Link/Act
On: Valid link
Flashing: Transmitting or receiving data
Off: Invalid link

Scenario 1: Connect Devices with and without Optical Interfaces

tp-link Enlarge Your Ethernet Network -figure 1

Scenario 2: Connect Devices without Optical Interfaces

tp-link Enlarge Your Ethernet Network -figure 2

Specifications

General Specifications

Standards IEEE 802.3, IEEE 802.3i, IEEE802.3u
LED PWR, Link/Act
Connector 1 SC fiber optic; 1 RJ45 jack
Twisted-Pair 100BASE-Tx: 2-pair UTP/STP of Cat. 5 or above (≤100 m)
Fiber 9/125 μm single-mode fiber (≤20 km)
WaveLength TL-FC111A-20: 1550 nm TX, 1310 nm RX
TL-FC111B-20: 1310 nm TX, 1550 nm RX
Power External Power Adapter: 5 V/0.6 A
Dimensions External Power Adapter: 5 V/0.6 A

Environmental and Physical Specifications

Operating Temperature 0˚C to 50˚C (32˚F to 122˚F)
Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)
Operating Humidity 10% to 90% RH  non-condensing
Storage Humidity 5% to 90% RH  non-condensing

tp-link Enlarge Your Ethernet Network -iconTo ask questions, find answers, and communicate with TP-Link users or engineers, please visit https://community.tp-link.com to join TP-Link
Community.
tp-link Enlarge Your Ethernet Network -icon 1For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.

tp-link Enlarge Your Ethernet Network - qr codehttp://www.tp-link.com/support

tp-link Enlarge Your Ethernet Network -icon 3If you have any suggestions or needs on the product guides, welcome to email techwriter@tp-link.com.cn.

Safety Information
Keep the device away from water, fire, humidity, or hot environments.

  • Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
  • Do not use a damaged charger or USB cable to charge the device.
  • Do not use any other chargers other than those recommended.
  • The adapter shall be installed near the equipment and shall be easily accessible.
  • Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.

Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due
to improper use of the device. Please use this product with care and operate at your own risk.

EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.

tp-link Enlarge Your Ethernet Network -figure 4

©2020 TP-Link 7106508844 REV1.0.0

Documents / Resources

tp-link Enlarge Your Ethernet Network [pdf] User Guide
tp-link, Enlarge, Your, Ethernet, Network, 10 Mbps, 100 Mbps, WDM, Media, Converter

References

Leave a comment

Your email address will not be published. Required fields are marked *