TOSIBOX NODE675 Industrial Wireless Access Points User Manual

Avoid operating the device in areas with explosive atmospheres
or near sensitive equipment.
Power off the device and cellular modem in sensitive areas to
prevent radio interference.

FAQ:

Q: What is the Tosibox Key?

A: The Tosibox Key is an intelligent USB-connected device with a
secure cryptoprocessor used to establish secure connections to the
endpoint device. It ensures interoperability between Keys and
devices.

Q: What are Sub Key and Backup Key?

A: Sub Key has restricted access rights, while Backup Key is a
duplicated backup copy of the original Key. Matched Keys and
devices are automatically synchronized between the original Key and
Backup Key.

“`

View Fullscreen

Tosibox endpoint devices
User Manual

Contents
1 Introduction………………………………………………………………………………………………………………………… 4 2 Regulatory information ………………………………………………………………………………………………………… 5
2.1 Tosibox endpoint device intended use……………………………………………………………………………. 5 2.2 Important notice for wireless operation …………………………………………………………………………… 5 2.3 Safety and hazards ……………………………………………………………………………………………………… 5 2.4 Informations réglementaire …………………………………………………………………………………………… 5 2.5 Domaine d’application du Tosibox endpoint device ………………………………………………………….. 5 2.6 Information importante pour l’utilisation du réseau sans fil ………………………………………………… 6 2.7 Sécurité et dangers ……………………………………………………………………………………………………… 6 2.8 Overview ……………………………………………………………………………………………………………………. 6 2.9 Tosibox Key ……………………………………………………………………………………………………………….. 6 2.10 Tosibox Lock………………………………………………………………………………………………………………. 7 3 Getting started ……………………………………………………………………………………………………………………. 7 3.1 Deploying in Lock mode……………………………………………………………………………………………….. 7 3.2 Deploying endpoint device in client mode……………………………………………………………………….. 8 3.3 Lock Sub Lock connection …………………………………………………………………………………………. 8 3.4 Updating the device software………………………………………………………………………………………… 9 3.5 Cellular modem settings ………………………………………………………………………………………………. 9 3.6 WLAN settings ……………………………………………………………………………………………………………. 9 3.7 Advanced settings……………………………………………………………………………………………………….. 9 3.8 Service port………………………………………………………………………………………………………………. 10 3.9 Input powering options……………………………………………………………………………………………….. 10 4 Maintenance instructions……………………………………………………………………………………………………. 10 5 Technical data ………………………………………………………………………………………………………………….. 11 5.1 TOSIBOX 175 …………………………………………………………………………………………………………… 11 5.2 TOSIBOX 350 …………………………………………………………………………………………………………… 12 5.3 TOSIBOX 375 …………………………………………………………………………………………………………… 13 5.4 TOSIBOX 610 …………………………………………………………………………………………………………… 14 5.5 TOSIBOX 675 …………………………………………………………………………………………………………… 14 5.6 TOSIBOX 695 …………………………………………………………………………………………………………… 16 6 Limited warranty ……………………………………………………………………………………………………………….. 17 7 Legal notices ……………………………………………………………………………………………………………………. 18 8 Mentions légales ………………………………………………………………………………………………………………. 19 9 Declarations …………………………………………………………………………………………………………………….. 19 9.1 TOSIBOX 175 …………………………………………………………………………………………………………… 19

2 / 27

9.2 TOSIBOX 350 and TOSIBOX 375 ……………………………………………………………………………….. 20 9.3 TOSIBOX 610 …………………………………………………………………………………………………………… 21 9.4 TOSIBOX 650 …………………………………………………………………………………………………………… 22 9.5 TOSIBOX 670 …………………………………………………………………………………………………………… 23 9.6 TOSIBOX 675 …………………………………………………………………………………………………………… 24 9.7 TOSIBOX 695 …………………………………………………………………………………………………………… 27

3 / 27

1 Introduction
Congratulations on choosing the Tosibox solution!
Tosibox is globally audited, patented and performs at the highest security levels in the industry. The technology is based on two-factor authentication, automatic security updates and the latest encryption technology.
Tosibox solution consists of modular components that offer unlimited expandability and flexibility. All Tosibox products are compatible with each other and are internet connection and operator agnostic. Tosibox creates a direct and secure VPN tunnel between the physical devices. Only trusted devices can access the network.

Technical support: support@tosibox.com Global support: www.tosibox.com/support Knowledge base: https://helpdesk.tosibox.com Tosibox is patented, incl. US8831020, US9900178, US14/119753, US14/39015

4 / 27

2 Regulatory information
2.1 Tosibox endpoint device intended use
The device is used for controlling other devices remotely over the Internet via a VPN connection. To be installed into a DIN rail, inside a cabinet with the controlled devices. Alternatively, the device may be standing on its rubber feet on a table or a shelf. The product conformity with the requirements is guaranteed only when using the antennas supplied with the product. The use of other antennas will void the conformity and is not allowed.
2.2 Important notice for wireless operation
Because of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a wellconstructed network, TOSIBOX Node with cellular modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property.
Tosibox Oy and its affiliates accept no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using TOSIBOX endpoint device with cellular modem, or for failure of the TOSIBOX endpoint device with cellular modem to transmit or receive such data.
2.3 Safety and hazards
At least 20 cm separation distance between the antennas and persons must be maintained at all times.
Do not operate your device with cellular modem:
In areas where blasting is in progress
Where explosive atmospheres may be present including refueling points, fuel depots, and chemical plants
Near medical equipment, life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the device and the cellular modem MUST BE POWERED OFF. Otherwise, the cellular modem can transmit signals that could interfere with this equipment.
In an aircraft, the Node and the cellular modem MUST BE POWERED OFF. Otherwise, the device and the cellular modem can transmit signals that could interfere with various onboard systems and may be dangerous to the operation of the aircraft or disrupt the cellular network. Use of a cellular phone in an aircraft is illegal in some jurisdictions. Failure to observe this instruction may lead to suspension or denial of cellular telephone services to the offender, or legal action or both. Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. The device and the cellular modem may be used normally at this time.
2.4 Informations réglementaire
2.5 Domaine d’application du Tosibox endpoint device
Le Lock permet de contrôler des équipements distants à travers Internet en créant une connexion VPN. Il peut être installé sur un rail DIN dans une armoire à côté des équipements à contrôler. Il peut aussi

5 / 27

être posé sur ses patins en caoutchouc sur une table ou une étagère. La conformité des caractéristiques de l’équipement est seulement garantie avec l’installation des antennes livrées. L’utilisation d’autre antenne annulera la conformité et n’est pas autorisée.
2.6 Information importante pour l’utilisation du réseau sans fil
En raison de la nature des communications sans fils, les données transmises et reçues ne peuvent être garanties. Les données peuvent être retardées, corrompues (avoir des erreurs) ou être complètement perdues. Bien que les pertes ou les retards de données soient rares lorsque les équipements sont utilisés dans des conditions normales dans des réseaux construits avec les règles de l’art, le TOSIBOX® Node avec un modem cellulaire ne devrait pas être utilisé dans les cas où les erreurs de transmission ou de réception de données pourraient entrainer des dommages de quelque nature que ce soit pour l’utilisateur ou pour une tierce partie, incluant mais ne limitant pas les blessures physiques, la mort ou la perte de jouissance.
Tosibox Oy et ses filiales ne pourront être tenues pour responsables des dommages de quelque nature que ce soit résultant de retards ou d’erreurs dans les données transmises ou reçues en utilisant un TOSIBOX Node avec modem cellulaire ou des problèmes créés par l’équipement TOSIBOX® Node avec modem cellulaire lors de transmission ou réception de ces données.
2.7 Sécurité et dangers
Une distance minimale de 20 cm entre les antennes et les personnes doit être respectée à tout moment.
N’utilisez pas votre Node avec un modem cellulaire interne ou externe :
Dans les zones des explosions sont est en cours
Où des atmosphères explosives peuvent être présentes, y compris des points de ravitaillement en carburant, des dépôts de carburant et des usines chimiques
À proximité d’équipements médicaux, d’équipements de survie, ou de tout équipement susceptible de subir toute forme d’interférence radio. Dans ces zones, le Node et le modem cellulaire DOIVENT ÊTRE ÉTEINTS, sous peine d’émission de signaux par le modem cellulaire susceptibles d’interférer avec ces équipements.
Le Node et le modem cellulaire DOIVENT ÊTRE ÉTEINTS dans un avion. Le Node et le modem cellulaire sont susceptibles de transmettre des signaux pouvant brouiller les systèmes de embarqués pouvant nuire au bon fonctionnement de l’appareil ou interférer avec les réseaux radio.
L’utilisation d’un téléphone cellulaire dans un avion est illégale dans certaines juridictions. Le non-respect de cette règle peut entraîner la suspension ou le refus des services de téléphonie cellulaire pour le contrevenant, ou des poursuites judiciaires, ou les deux. Certaines compagnies aériennes peuvent autoriser l’utilisation de téléphones cellulaires lorsque l’avion est au sol et que la porte est ouverte. Le Node et le modem cellulaire peuvent être utilisés normalement à ce moment.
2.8 Overview
2.9 Tosibox Key
TOSIBOX Key is an intelligent USB-connected device that contains a secure cryptoprocessor. The Key is used to establish a secure connection to the endpoint device. All TOSIBOX Keys and devices are interoperable.

6 / 27

SUB KEY
An additional Key that has restricted access rights.
BACKUP KEY
A duplicated backup copy of the Key. All matched Keys and devices are automatically synchronized between the original Key and the Backup Key.
2.10 Tosibox Lock
TOSIBOX Lock is a device that accepts remote connections from matched Keys and creates private and secure access to connected network devices. The network devices that are connected to the device LAN port are automatically found. The device automatically distributes IP addresses for the Keys, Sub Keys and the network devices connected to LAN port(s) of the device. The endpoint device can also control network devices with fixed IP addresses.
Device settings can be changed via service port, encrypted TOSIBOX VPN connection local network
Sub Lock
Sub Lock is a device that has been converted to Sub device mode. When connecting two devices to each other, one must be in Sub device mode of operation.
3 Getting started
Make sure the endpoint device is powered before proceeding to matching the Key with the device. Insert the Key into the USB port of the device. When the LED on the Key turns off, the matching is complete (approximately 10 seconds). Remove the Key from the device. You can also match additional endpoint devices to the same Key.
Connect the endpoint device to your network according to your use case. Remember to make sure that the device has a working internet connection.
Connect the Key to your computer and install the Key software.
Secure TOSIBOX connection is now ready to be used for controlling and monitoring devices remotely.
3.1 Deploying in Lock mode
With its factory default settings, the device is connected to the Internet via its WAN port, WLAN or cellular modem. In this mode, the endpoint device creates its own protected local network for the connected devices. In this configuration, only devices that are connected to the endpoint device by cable or via WLAN access point are accessible with the Key.
Note:
If the device is connected to a DHCP enabled network via any of its LAN ports the device’s own LAN functionality can be restored by resolving any DHCP conflicts by removing improper LAN connections to the device.
Connecting network devices in Lock mode
Connecting device(s) that use dynamic IP addresses (DHCP)
Devices with a DHCP client enabled will automatically connect to the endpoint device. Plug the device(s) into the device’s LAN port(s) and go!

7 / 27

Connecting device(s) with Fixed IP addresses by configuring the ENDPOINT DEVICE to the DEVICE:
1. Get the device IP addresses and netmask.
2. Connect your PC to the endpoint´s service port and log in following the step 1 on page 17 “Updating the endpoint device software”.
3. Go to Network->LAN and change the IP address in the “IPv4 address” field to the next IP address above the IP address of the device (step 1). Also check that the “IPv4 netmask” field corresponds to the netmask set on the device and change it if necessary.
4. Plug the devices into the endpoint device´s LAN ports and go!
3.2 Deploying in Client mode
Client mode can be used for connecting the device to an existing network (e.g. an office network). In this mode, the endpoint device joins the network like any other device (e.g. a PC) and provides remote users with access to other devices in the same network. The endpoint device will obtain its address from the DHCP, so the local network needs to have a working DHCP server that allocated IP addresses.
Connecting network devices in Client Mode
Log into the Node´s web user interface as admin and open the LAN settings by clicking Network > LAN.
Change the LAN interface protocol field to “DHCP Client”. Click the “Switch Protocol” button and click “Save”.
Plug in a cable from the local network into one of the Node´s LAN ports and go!
Note:
Do no connect the controlled devices to any LAN port. The endpoint device will scan the entire LAN network for connected devices and will grant device
access to any user with a matched Key. Please keep this in mind when considering network and information security. In cases where access rights need to be restricted, switch on MAC/IP Filtering (under Advanced Settings) or set up the device in its factory default configuration. In this mode, the endpoint device´s inbuilt firewall does not protect the devices in the LAN network. Client Mode is deactivated from the device’s web user interface
3.3 Lock Sub Lock connection
With TOSIBOX Lock one can connect machines in separate places so that the connection between them is permanently and automatically on. One example is a real-time protected connection between home and office. This is made with a Lock – Sub Lock connection.
TOSIBOX 175 can have up to 10 Sub Locks TOSIBOX 600 series can have up to 20 Sub Locks
First match the Key to all the devices to be connected.
Connecting endpoint devices
1. Insert a matched Key to the USB port of the computer. 2. Choose “Devices” from the Key user menu and “Connect devices” from the drop down menu. 3. Choose the devices that you want to connect together and choose “Next”.

8 / 27

4. Choose the endpoint device that you want to attach the Sub devices. The other devices will be changed to Sub device operating mode.
5. Confirm the selection > Save > matching is ready.
Note: The connections will come into effect when the devices have access to the Internet.
The Sub device ends of the connection in the picture do not have their own DHCP service. If the connection between the endpoint device and the Sub device is interrupted, the network devices connected with the Sub device can no longer connect to the Internet and each other.
3.4 Updating the endpoint device software
Connect the computer to the service port of the device with an ethernet cable. First check that you have access to the Internet via the service port. Open an internet browser and type http://172.17.17.17 into the address field to access the Node user interface. Do not type “www” before the “http://” in the address. b. Alternatively you can also log in remotely. When the connection between the Key and the device is active, double click the endpoint device symbol in the Key user interface.
Log in using “admin” for the user ID. The default admin password is visible on the bottom of the device.
Choose “Settings” > “Software update”. If there is a software update available for the device, you can start the update by clicking the “Start software update” button.*
Wait until the update has been downloaded and installed. Do not interrupt the power of the device during the software update process. The update is complete when the software gives a notice “Software updated successfully”.
Automatic software updates are activated as a default setting. You can select the time when the automatic update of the released software is allowed. You can deactivate the automatic software update from the endpoint device user interface.
Choose “Settings” > “Software update” > uncheck the box “Auto-update enabled”.
3.5 Cellular modem settings
You can connect the Node to the Internet with a cellular modem. Before inserting or removing the SIM card(s), disconnect the Node power supply.
Log in as admin user, select “Network” > “Internal Modem” Either use the Automatic APN setting or fill in the APN and if necessary the PIN field according to
the SIM card settings. For APN settings information, please contact your mobile operator.
3.6 WLAN settings
You can configure the WLAN as Client (providing Internet access for the Lock) or as Access Point (providing access to Lock LAN and Internet for wireless devices). For detailed set-up instructions visit www.tosibox.com/support.
3.7 Advanced settings
On the Advanced settings page you can configure LAN and Internet access restrictions and security related settings as well as time zone and NTP server settings. NTP settings are applicable to all products.
1. Log in as admin

9 / 27

2. Choose “Settings” > “Advanced settings” 3. Confirm changes > Save
3.8 Service port
TOSIBOX endpoint devices provide a Service port mechanism to allow login in case device is misconfigured. Enabling Service port sets the last LAN port (typically LAN3) into Service port mode where local login is possible with following settings:
Node management interface IP: 172.17.17.17 DHCP server: enabled
To enable Service port
Remove cable from the Service port (typically LAN3) port Press the reset button for 3 seconds
When completed, the Internet status LED will blink for three seconds. The Node Management Interface can then be accessed by entering management IP address on the address bar of your browser. Assigning the port back to LAN range can be done following the same procedure or by restarting the device.
3.9 Input powering options
TOSIBOX 175
Use the AC adapter included in the sales package. Alternatively, in case the operating voltage of 9-35V DC (absolute value) is available from an external power source, a DC input plug included in the sales package can be used. Connect the stripped wires by tightening the screws with a flat blade screwdriver. Follow the polarity marking in the plug.
TOSIBOX 600-SERIES
Use the AC adapter included in the sales package. Alternatively, in case the operating voltage of 9-50V DC (absolute value) is available from an external power source, a DC input can be used.
TOSIBOX 300-SERIES
Use the AC adapter included in the sales package. Alternatively, in case the operating voltage of 5-35V DC (absolute value) is available from an external power source, a DC input can be used.
4 Maintenance instructions
Treat your TOSIBOX devices with care. By observing the following maintenance instructions, you can enjoy the maximum performance of the devices and ensure full warranty coverage.
Keep the devices dry. Protect the devices from precipitation, moisture and liquids as they can cause corrosion to electronic circuits. The devices are intended for indoor use only. Do not use them in wet environment or outdoors.
Protect the devices from dirt and dust. When necessary, clean the devices with a soft, dry cloth. Do not use chemicals, solvents, detergents or pressurized air.
Protect the devices from heat. High temperatures can damage plastic parts and shorten the life of the electronics.
Protect the devices from cold. Low temperatures can make them more susceptible to breakage. Let the device’s temperature stabilize properly before deploying them into the network.

10 / 27

Protect the devices from mechanical shocks. Do not shake, knock or drop the devices. Do not paint the devices. Do not cover the devices or install them on top of each other. This can cause overheating. Allow
enough free space around the devices to ensure the free flow of cooling air. Do not open the devices. There are no serviceable parts inside the devices. If the devices
malfunction or need servicing, contact an authorized service facility. After the service life of the devices is over, do not throw them into domestic waste. Instead, take
them to an authorized waste electronics collection facility.
5 Technical data
5.1 TOSIBOX 175
Ports
1 x RJ-45 WAN connection, 10/100 Mb/s, auto-negotiation (MDI / MDI-X) 1 x RJ-45 LAN connection, 10/100 Mb/s, auto-negotiation (MDI / MDI-X) LAN can be assigned as Service connection, 10/100 Mb/s, auto-negotiation (MDI / MDI-X) RS485 port is not supported in the software. The device can be powered through the port
Connections
9-35V DC 2 x WiFi antenna connector, RP-SMA female 1 x LTE antenna connector, SMA female DIN rail attachment (back)
4G Module
Cellular module: Quectel EG25-G Region: Global LTE Cat-4 Up to 150 Mbps DL, 50 Mbps UL
Frequency Bands
LTE FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28 LTE TDD: B38, B39, B40, B41 WCDMA: B1, B2, B4, B5, B6, B8, B19
WLAN
IEEE 802.11 b/g, 2.4 GHz, max. 150 Mbps Encryptions WEP, WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed mode Frequency 2.412 2.462 GHz, 11 channels Access point or client mode Output power 15 dBm max
Physical properties
Size 104 mm x 28 mm x 110 mm / 4.09″ x 1.10″ x 4.33″ Weight 305 g / 0.67 lbs (net weight article)

11 / 27

Storage Temperature
Node -30°C … +70°C / -22°F … +158°F Power supply -20°C … +80°C / -4°F … +176°F
Operating Temperature
Node -20°C … +55°C / -4°F … +131°F Power supply 0°C … +40°C / 32°F … +104°F
5.2 TOSIBOX 350
Ports
1 x RJ-45 WAN connection, 10/100 Mbps, auto-negotiation (MDI / MDI-X) 4 x RJ-45 LAN connection, 10/100 Mbps, auto-negotiation (MDI / MDI-X) 1 x USB 2.0, type A
Connections
2 pin industrial DC power socket 6-Pin 3.5mm Digital IO socket (6-Pin serial interface not supported in software) 5-35V DC, reverse polarity protection, voltage surge/transient protection 1 x RP-SMA for WiFi DIN rail mounting in the back Maximum power consumption 10W
WLAN
IEEE 802.11 b/g/n, 2.4 GHz, max. 54 Mbps Encryptions WEP, WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed mode Frequency 2.412 2.462 GHz, 11 channels Access point or client mode Output power 20 dBm max
I/O specifications
2 x Digital input, 0 – 30 V as logic high 2 x Digital output, relay, up to 5A and 30 VDC/250VAC output Software configurable I/O state
Physical properties
Size 145 mm x 114 mm x 45 mm / 5.71″ x 4.49″ x 1.77″ Protection class IP30 Weight 625 g / 1.37 lbs (net weight article)
Storage Temperature
Node -35 °C … +75 °C / -31 °F … +167 °F Power supply -20 °C … +80 °C /-4°F … +176 °F
Operating Temperature
Node -35 °C … +75 °C / -31 °F … +167 °F Power supply -10°C … +40°C / 14°F … +104°F
Copyright © 2025 Tosibox. All rights reserved.

12 / 27

5.3 TOSIBOX 375
Ports
1 x RJ-45 WAN connection, 10/100 Mbps, auto-negotiation (MDI / MDI-X) 4 x RJ-45 LAN connection, 10/100 Mbps, auto-negotiation (MDI / MDI-X) 1 x USB 2.0, type A
Connections
2 pin industrial DC power socket 6-Pin 3.5mm Digital IO socket (6-Pin serial interface not supported in software) 5-35V DC, reverse polarity protection, voltage surge/transient protection 1 x RP-SMA for WiFi DIN rail mounting in the back Maximum power consumption 10W
4G Module
Cellular module: Quectel EG25-G Region: GLOBAL LTE Cat-4 Up to 150 Mbps DL, 50 Mbps UL
Frequency Bands
LTE FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28 LTE TDD: B38, B39, B40, B41 WCDMA: B1, B2, B4, B5, B6, B8, B19
WLAN
IEEE 802.11 b/g/n, 2.4 GHz, max. 54 Mbps Encryptions WEP, WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed mode Frequency 2.412 2.462 GHz, 11 channels Access point or client mode Output power 20 dBm max
I/O specifications
2 x Digital input, 0 – 30 V as logic high 2 x Digital output, relay, up to 5A and 30 VDC/250VAC output Software configurable I/O state
Physical properties
Size 145 mm x 114 mm x 45 mm / 5.71″ x 4.49″ x 1.77″ (W x H x L) Protection class IP30 Weight 625 g / 1.37 lbs (net weight article)
Storage Temperature
Node -35 °C … +75 °C / -31 °F … +167 °F Power supply -20 °C … +80 °C /-4°F … +176 °F

13 / 27

Operating Temperature
Node -35 °C … +75 °C / -31 °F … +167 °F Power supply -10°C … +40°C / 14°F … +104°F
5.4 TOSIBOX 610
Ports
1x RJ-45 WAN connection, 10/100/1000 Mb/s, auto-negotiation (MDI / MDI-X) 3x RJ-45 LAN connection, 10/100/1000 Mb/s, auto-negotiation (MDI / MDI-X) 1x USB 2.0, type A
Connections
4 pin industrial DC power socket 9-50V DC, reverse polarity protection, voltage surge/transient protection DIN rail mounting slot in the back Maximum power consumption 6W
Digital I/O specifications
1x Digital input, 0-6 V detected as logic low, 8-30 V detected as logic high 1x Digital output, open collector output, max output 30 V, 300 mA Software configurable I/O state Requires separate I/O cable (accessory)
VLAN
802.1Q and 802.1ad compliancy Each LAN port on a separate subnet Inter-VLAN routing Access and trunk ports Tagged/Untagged VLAN traffic Selective LAN access via Key
Physical properties
Size 115 mm x 32 mm x 95 mm / 4.52″ x 1.26″ x 3.74″ Protection class IP30 Weight 345 g / 0.76 lbs (net weight article)
Storage Temperature
Node -40°C … +75°C / -40°F … +167°F Power supply -20°C … +70°C / -4°F … +158°F
Operating Temperature
Node -40°C … +75°C / -40°F … +167°F Power supply -10°C … +40°C / 14°F … +104°F
5.5 TOSIBOX 675
Ports
1x RJ-45 WAN connection, 10/100/1000 Mb/s, auto-negotiation (MDI / MDI-X)
Copyright © 2025 Tosibox. All rights reserved.

14 / 27

3x RJ-45 LAN connection, 10/100/1000 Mb/s, auto-negotiation (MDI / MDI-X) 1x USB 2.0, type A
Connections
4 pin industrial DC power socket 9-50V DC, reverse polarity protection, voltage surge/transient protection 2x RP-SMA for WiFi 2x SMA for LTE 1x GNSS DIN rail mounting slot in the back and on both sides Maximum power consumption 16W
4G Module for TBL675 US and Canada
Cellular module: Quectel EG060K-NA Region: North America LTE Cat-6 Up to 300 Mbps DL, 50 Mbps UL Dual SIM Frequency Bands
LTE FDD: B2, B4, B5, B7, B12, B13, B14, B25, B26, B29, B66, B71 LTE-TDD: B41
4G Module for TBL675 EMEA and APAC
Cellular module: Quectel EG060K-EA Region: EMEA/Australia/Brazil LTE Cat-6 Up to 300 Mbps DL, 50 Mbps UL Dual SIM Frequency Bands
LTE FDD: B1, B3, B5, B7, B8, B20, B28, B32 LTE TDD: B38, B40, B41 WCDMA: B1, B3, B5, B8
WLAN
IEEE 802.11 b/g/n, 2.4 GHz, max. 150 Mbps Encryptions WEP, WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed mode Frequency 2.412 2.462 GHz, 11 channels Access point or client mode Output power 20 dBm max
Digital I/O specifications
1x Digital input, 0-6 V detected as logic low, 8-30 V detected as logic high 1x Digital output, open collector output, max output 30 V, 300 mA Software configurable I/O state Requires separate I/O cable (accessory)
VLAN
802.1Q and 802.1ad compliancy
Copyright © 2025 Tosibox. All rights reserved.

15 / 27

Each LAN port on a separate subnet Inter-VLAN routing Access and trunk ports Port and IP based configuration Tagged/Untagged VLAN traffic Selective LAN access via Key Max 127 concurrent VLANs
Physical properties
Size 115 mm x 44 mm x 95 mm / 4.52″ x 1.74″ x 3.74″ Protection class IP30 Weight 456 g / 1.00 lbs (net weight article)
Storage Temperature
Node -40°C … +75°C / -40°F … +167°F Power supply -20°C … +70°C / -4°F … +158°F
Operating Temperature
Node -40°C … +75°C / -40°F … +167°F Power supply -10°C … +40°C / 14°F … +104°F
5.6 TOSIBOX 695
Ports
1x RJ-45 WAN connection, 10/100/1000 Mb/s, auto-negotiation (MDI / MDI-X) 4x RJ-45 LAN connection, 10/100/1000 Mb/s, auto-negotiation (MDI / MDI-X) 1x USB 2.0, type A
Connections
4 pin industrial DC power socket 9-50V DC, reverse polarity protection, voltage surge/transient protection 2x RP-SMA for WiFi 4x SMA for 5G/LTE 1x GNSS DIN rail mounting slot in the back and on both sides Maximum power consumption 18W
5G/LTE Module
Cellular module: Quectel RG501Q-EU Region: EMEA/APAC/Brazil (excluding China) Sub-6 GHz 5G SA Sub-6 up to 2.1 Gbps DL, 900 Mbps UL 5G NSA Sub-6 up to 3.3 Gbps DL, 600/650 Mbps UL LTE-FDD up to 2 Gbps DL, 200 Mbps UL Dual SIM single standby All antennas are equal
Copyright © 2025 Tosibox. All rights reserved.

16 / 27

Frequency Bands 5G NR: n1, n3, n5, n7, n8, n20, n28, n38, n40, n41, n77, n78 LTE-FDD: B1, B3, B5, B7, B8, B20, B28, B32 LTE-TDD: B38, B40, B41, B42, B43 WCDMA: B1, B5, B8
WLAN
IEEE 802.11 b/g/n, 2.4 GHz, max. 150 Mbps Encryptions WEP, WPA-PSK, WPA2-PSK, WPA-PSK/WPA2-PSK mixed mode Frequency 2.412 2.462 GHz, 11 channels Access point or client mode Output power 20 dBm max
Digital I/O specifications
1x Digital input, 0-6 V detected as logic low, 8-30 V detected as logic high 1x Digital output, open collector output, max output 30 V, 300 mA Software configurable I/O state Requires separate I/O cable (accessory)
VLAN
802.1Q and 802.1ad compliancy Each LAN port on a separate subnet Inter-VLAN routing Access and trunk ports Tagged/Untagged VLAN traffic Selective LAN access via Key
Physical properties
Size 132 mm x 44 mm x 95 mm / 4.52″ x 1.74″ x 3.74″ Protection class IP30 Weight 533 g / 1.17 lbs (net weight article)
Storage Temperature
Node -40°C … +75°C / -40°F … +167°F Power supply -20°C … +70°C / -4°F … +158°F
Operating Temperature
Node -40°C … +75°C / -40°F … +167°F Power supply -10°C … +40°C / 14°F … +104°F
6 Limited warranty
Subject to the exclusions set forth below, Tosibox will repair or replace, at its option without charge, any TOSIBOX product which fails due to a defect in material or workmanship within 24 months following the initial consumer purchase.
This warranty does not apply to water damage, abuse or misuse of unauthorized accessories, unauthorized service or modification or altered products.

17 / 27

This warranty does not include the cost of labor for removal or re-installation of the product.
ANY IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED AS SET FORTH HEREIN AND TO THE DURATION OF THE LIMITED WARRANTY, OTHERWISE THE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. IN NO EVENT SHALL TOSIBOX OY BE LIABLE, WHETHER IN CONTRACT OR TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE, GROSS NEGLIGENCE, BODILY INJURY, PROPERTY DAMAGE AND DEATH) FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATA OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW.
The complete information about Tosibox Terms and Conditions is available at:
https://www.tosibox.com/regulatory-information
For Product Purchased in the USA:
Performance of any obligation under this warranty may be obtained by returning the warranted product, prepaid freight, along with proof of purchase to:
Tosibox, Inc. 11770 Haynes Bridge Rd Suite 205-101 Alpharetta, GA 30004
This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
Note: The above warranty applies only to merchandise purchased in the United States of America or any of the territories or possessions thereof, or from a U.S. Military exchange.
For Product Purchased in Canada:
Performance of any obligation under this warranty may be obtained by returning the warranted product, along with proof of purchase, to your place of purchase in Canada.
This warranty gives you specified legal rights. Additional warranty rights may be provided by law in some within Canada
7 Legal notices
© 2025 Tosibox Oy. All rights reserved.
Reproduction, distribution or storage of part or all of the content of this document without the prior written permission of Tosibox is prohibited.
Because of continuous product development, Tosibox reserves the right to change and improve any product mentioned herein without prior notice.
Tosibox shall not take responsibility of any loss of information or income or any special, incidental, consequential or indirect damages.

18 / 27

The contents of this document are provided “as is”. No warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Tosibox reserves the right to revise this document or withdraw it at any time without prior notice.
Tosibox products contain technology that is based on open source software. When requested by the customer, Tosibox will deliver more detailed information from the parts that the licenses require. Source code requests can be submitted to: sourcecode.request@tosibox.com
Tosibox Oy Elektroniikkatie 2 A 90590 OULU, FINLAND
8 Mentions légales
© 2025 Tosibox Oy. Tous les droits sont réservés.
La reproduction, la distribution ou le stockage de tout ou partie du contenu de ce document sans l’autorisation écrite préalable de Tosibox est interdite.
En raison du développement continu du produit, Tosibox se réserve le droit de modifier et d’améliorer tous produits mentionnés dans le présent document sans préavis.
Tosibox ne pourra être tenu responsable de toutes les pertes d’informations ou de revenus ou autres dommages, indirects ou consécutifs.
Aucune garantie sous quelque forme que ce soit, explicite ou implicite, y compris, mais sans y limiter les garanties implicites d’aptitude à la commercialisation, à l’adéquation à un usage particulier, n’est donnée en ce qui concerne l’exactitude, la fiabilité ou le contenu de ce document.
Tosibox se réserve le droit de réviser ce document ou de le retirer à tout moment sans préavis.
Les produits Tosibox contiennent une technologie basée sur un logiciel open source. À la demande du client, Tosibox fournira des informations plus détaillées sur les composants requis par les licences. Les demandes de code source peuvent être envoyées à: sourcecode.request@tosibox.com
Tosibox Oy Elektroniikkatie 2 A 90590 OULU, FINLANDE
9 Declarations
9.1 TOSIBOX 175
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 175 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at https://www.tosibox.com/tosibox-for-sites.
This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Tosibox Inc. 1212 Corporate Drive, Suite 170

19 / 27

Irwing, TX 75038 Tel: +1 478 419-8674 www.tosibox.com
FCC ID: 2AHCNTBNODE contains FCC ID: XMR201903EG25G
Federal Communication Commission interference statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. Consult the dealer or an experienced radio/TV technician for help.
This radio device has been tested to operate with the external antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
TOSIBOX 175: Wi-Fi monopole antenna, 50 ohm, max peak gain 0.4 dBi.
Brazilian compliance, conformidade brasileiro
Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados.
Para maiores informações, consulte o site da ANATEL
www.gov.br/anatel.
9.2 TOSIBOX 350 and TOSIBOX 375
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 350 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following Internet address: https://www.tosibox.com/tosibox-for-sites.

20 / 27

This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
UL declaration of conformity
This device is UL listed in USA and Canada with UL file number E497243.
Federal Communication Commission interference statement
This device complies with FCC part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Tosibox Inc. 1212 Corporate Drive, Suite 170 Irwing, TX 75038 Tel. +1 478 419-8674 www.tosibox.com
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate this equipment.
TOSIBOX 350
FCC ID: 2AHCNNODE350
TOSIBOX 375
FCC ID: 2AHCNNODE350 contains FCC ID: XMR201903EG25G
This radio device has been tested to operate with the external antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
350: Wi-Fi monopole antenna, 50 ohm, max peak gain 2.0 dBi.
375: Wi-Fi monopole antenna, 50 ohm, max peak gain 2.0 dBi.
9.3 TOSIBOX 610
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 610 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at https://www.tosibox.com/tosibox-for-sites.
This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Safety precaution
Do not use the provided power supply at temperatures exceeding 40C. To use the device in high temperatures, replace the power supply with a source rated for the used temperature.

21 / 27

Power supply parameters
Input 100 240 VAC, frequency 50/60Hz, 0.8A Output 24 VDC, 1.0 A, max 24 W Exchangeable input connector with EU (Type C), UK (Type G), US (Type A), AU (Type I) Operating temperature max +40C
9.4 TOSIBOX 650
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 650 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at https://www.tosibox.com/tosibox-for-sites.
This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Safety precaution
Do not use the provided power supply at temperatures exceeding 40C. To use the device in high temperatures, replace the power supply with a source rated for the used temperature.
Power supply parameters
Input 100 240 VAC, frequency 50/60Hz, 0.8A Output 24 VDC, 1.0 A, max 24 W Exchangeable input connector with EU (Type C), UK (Type G), US (Type A), AU (Type I) Operating temperature max +40C
Federal Communication Commission interference statement
This device complies with FCC part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Tosibox Inc. 1212 Corporate Drive, Suite 170 Irwing, TX 75038 Tel. +1 478 419-8674 www.tosibox.com
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate this equipment.
FCC ID: 2AHCNLOCK675 IC: 25009-LOCK675
This radio device has been tested to operate with the external antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
TOSIBOX 650: Wi-Fi monopole antenna, 50 ohm, max peak gain 3.5 dBi.

22 / 27

Industry Canada statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter IC: 25009-NODE675 has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
TOSIBOX 650: Wi-Fi monopole antenna, 50 ohm, max peak gain 3.5 dBi.
Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication!
This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Le CI émetteur radio: 25009-NODE675 a été approuvé par ISED pour fonctionner avec les types d’antennes énumérés ci-dessous avec le gain maximal admissible indiqué. Les types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits d’utilisation avec cet appareil.
TOSIBOX 650: antenne Wi-Fi unipolaire, 50 ohm, gain de crête max 3.5 dBi.
Selon les réglementations ISED, cet émetteur radio ne peut fonctionner qu’avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par ISED. Afin de réduire les interférences radio potentielles avec d’autres utilisateurs, le type d’antenne et son gain doivent être choisis de manière à ce que la puissance rayonnée isotrope équivalente (par exemple) ne soit pas supérieure à celle nécessaire pour une bonne communication!
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre l’antenne et l’utilisateur ou des tiers.
9.5 TOSIBOX 670
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 670 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at https://www.tosibox.com/tosibox-for-sites
This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

23 / 27

Safety precaution
Do not use the provided power supply at temperatures exceeding 40C. To use the device in high temperatures, replace the power supply with a source rated for the used temperature.
Power supply parameters
Input Voltage 100-240 VAC, 0.6A Input Frequency 50/60 Hz Output Voltage 12 VDC Output Current 1.5 A Operating temperature max +40C
Federal Communication Commission interference statement
This device complies with FCC part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Tosibox Inc. 1212 Corporate Drive, Suite 170 Irwing, TX 75038 Tel. +1 478 419-8674 www.tosibox.com
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate this equipment.
Contains FCC ID XMR201807EG06A IC contains 10224A-201807EG06A
This radio device has been tested to operate with the external antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
TOSIBOX 670: Wi-Fi monopole antenna, 50 ohm, max peak gain 3.5 dBi.
9.6 TOSIBOX 675
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 675 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at https://www.tosibox.com/tosibox-for-sites.
This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Safety precaution
Do not use the provided power supply at temperatures exceeding 40C. To use the device in high temperatures, replace the power supply with a source rated for the used temperature.

24 / 27

Power supply parameters for Tosibox 675 US
Input 100 240 VAC, frequency 50/60Hz, 0.6A Output 12 VDC, 1.5 A, max 18 W Input connector US (Type A) Operating temperature max +40C
Power supply parameters for Tosibox 675
Input 100 240 VAC, frequency 50/60Hz, 0.8A Output 24 VDC, 1.0 A, max 24 W Exchangeable input connector with EU (Type C), UK (Type G), US (Type A), AU (Type I) Operating temperature max +40C
Federal Communication Commission interference statement
This device complies with FCC part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Tosibox Inc. 1212 Corporate Drive, Suite 170 Irwing, TX 75038 +1 478 419-8674 www.tosibox.com
FCC CAUTION: Any changes or modifications not expressly approved by the party responsible for compliance could void the user´s authority to operate this equipment.
FCC ID: 2AHCNNODE675 FCC ID contains: XMR2022EG060KNA IC: 25009-NODE675 IC contains: 10224A-2022EG060KNA
This radio device has been tested to operate with the external antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

25 / 27

Antenna Information

Brand TELTONIKA
TAOGLAS

Part No. PR14RD35 (main) PR14RD35 (aux) TG.30.8113

Type Dipole
Dipole

Gain (dBi) 2.76 for 2.4GHz 2.76 for 2.4GHz 4.29 for LTE Band 2 4.29 for LTE Band 4 3.00 for LTE Band 5 4.73 for LTE Band 7 3.00 for LTE Band 12 3.00 for LTE Band 13 3.00 for LTE Band 14 4.29 for LTE Band 25 3.00 for LTE Band 26 (814-824MHz) 3.00 for LTE Band 26 (824-849MHz) 4.73 for LTE Band 41 4.29 for LTE Band 66 3.00 for LTE Band 71

Industry Canada statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This radio transmitter IC: 25009-NODE675 has been approved by ISED to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication!
This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Le CI émetteur radio IC: 25009-NODE675 a été approuvé par ISED pour fonctionner avec les types d’antennes énumérés ci-dessous avec le gain maximal admissible indiqué. Les types d’antenne non inclus dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont strictement interdits d’utilisation avec cet appareil.
Selon les réglementations ISED, cet émetteur radio ne peut fonctionner qu’avec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par ISED. Afin de réduire les interférences radio potentielles avec d’autres utilisateurs, le type d’antenne et son gain doivent être choisis de manière

26 / 27

à ce que la puissance rayonnée isotrope équivalente (par exemple) ne soit pas supérieure à celle nécessaire pour une bonne communication!
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre l’antenne et l’utilisateur ou des tiers.
9.7 TOSIBOX 695
EU declaration of conformity
Hereby, Tosibox Oy declares that the radio equipment type 695 is in compliance with directive 2014/53/EU. The full text of the EU declaration of conformity is available at https://www.tosibox.com/tosibox-for-sites.
This equipment should be installed and operated with a minimum distance of 20cm between the antenna and the user or bystanders. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Safety precaution
Do not use the provided power supply at temperatures exceeding 40C. To use the device in high temperatures, replace the power supply with a source rated for the used temperature.
Power supply parameters
Input Voltage 100-240 VAC, 0.6A Input Frequency 50/60 Hz Output Voltage 12 VDC Output Current 1.5 A Operating temperature max +40C

27 / 27

Documents / Resources

TOSIBOX NODE675 Industrial Wireless Access Points [pdf] User Manual
NODE675, NODE675 Industrial Wireless Access Points, Industrial Wireless Access Points, Wireless Access Points, Access Points

References

User Manual

TOSIBOX NODE675 Industrial Wireless Access Points User Manual

NODE675 Industrial Wireless Access Points

Specifications:

Product Usage Instructions:

Installation:

Wireless Operation:

FAQ:

Q: What is the Tosibox Key?

Q: What are Sub Key and Backup Key?

Documents / Resources

References

Leave a comment

Cancel reply