TOPWISE T6 Android Smart Mobile POS User Manual

Physical Features: Function key, Power key, Type-C port,
Indicator LEDs, NFC reader area, ICCR card slot, MSR card slot,
Light-sensor, Rear Camera, Top Camera, Speaker, POGO Pin,
Printer
Mobile Network: Yes

Wireless: Yes
Card Slots: 1

Audio: Yes
Positioning: Yes

Ports: Charge Port, POGO Pin
Sensor: Yes

Power: Battery

Usage Instructions

Power ON/OFF

Power ON: Press and hold the power key until
the LCD screen turns on.

Power OFF: Press and hold the power key until
the LCD screen turns off.

Charge

Insert the USB cable into the charge port.

Connect the other end of the USB cable to a power source or
adapter.
Charge until the battery is fully charged.

Using the Device

To use the device:

Slide or swipe the screen as required.

Follow on-screen instructions for different functions like card
transactions or printing.
Ensure proper handling to avoid damage to the device.

FAQ

Q: What type of paper should be used for printing?

A: Please use thermal printing paper with a
thickness of 0.05-0.085mm.

Q: How often should the battery be charged?

A: To maintain battery capacity, charge the
device regularly (every 3-6 months is recommended).

Q: When should the battery be replaced?

A: Replace the battery every 2-3 years, even if
it appears to be functioning normally.

Q: What should be done if any components are missing from the
package?

A: If any components are missing, please
contact customer service immediately.

“`

View Fullscreen

BankCard 08/16
User Manual

Model: T6 Made in China

Android Smart Mobile POS.
T6

Contents Checklist

CONTENTS

Device

×1

Manual

×1

USB Cable

×1

Adapter

×1

Paper Roller

×1

BASE(optional)

×1

After unpacking your terminal, please verify all items are included in the package. If any components are missing, please contact customer service immediately.
Note: Please use thermal printing paper with a thickness of 0.05-0.085mm

Usage and Safety Guidelines
Water Protection Guidelines
1. Always power off the device before cleaning. 2. Use only non-corrosive cleaning agents. 3. Never submerge the device in water or any liquid. 4. Take care to prevent water or cleaning solution from entering the card reader or keypad.
Lithium Battery Safety Guidelines
1. Handle batteries with care – improper handling may cause fire or explosion. 2. Only use the provided adapter to charge the battery. 3. Keep the battery away from water, liquids, fire, and high temperatures. 4. Do not puncture, crush, or strike the battery with sharp or hard objects.

4. Do not puncture, crush, or strike the battery with sharp or hard objects.
5. To maintain battery capacity, charge the device regularly (every 3-6 months is recommended).
6. Replace the battery immediately if it: · Shows any deformation (such as bulging) · Has physical damage · Leaks any substance · Produces unusual odors
7. Replace the battery every 2-3 years, even if it appears to be functioning normally.
8. Dispose of used batteries according to local environmental regulations.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
The device has been tested and comply with FCC SAR limits. For body mode, please keep the device minimum 10mm when normal use.

Specification

OS Processor
Memory
Display
Printer Camera
Physical Key Card Readers Mobile Network
Wireless Card Slots
Audio Indicator LEDs Positioning
Port Sensor Power
Physical

Android 13 AP: 64bit Cortex A53 2.0 GHz SP: RISC Core ( ARMv7 – M )
2GB RAM + 32GB Flash 3GB + 32GB / 4GB + 64GB ( optional )
6.5″ HD 1600*720 IPS Capacitive Multi – Touch Screen
Print speed: 95mm/s | Paper Roll: 58*40mm 5 MP AF Rear – Facing ( 8MP AF optional ) 2 MP FF Top – Facing
Power × 1 | Function × 1 Chip & PIN | NFC Contactless | Magnetic Stripe 4G: FDD-LTE 3G: WCDMA | 2G: GPRS / GSM WiFi 2.4GHz / 5GHz | BT&BLE 1M TF Card × 1 | SIM x 2 + PSAM × 1 or SIM × 1 + PSAM × 2 ( esim × 1 optional )
Speaker × 1 Charging LED × 1 (Red + Green ) GPS L1 C/A, BDS B1l, Galileo E1 SBAS L1: 1559-1610MHz(RX) USB Type-C × 1 Light-sensor | G-sensor Battery: 7.2V / 2600mAh Adapter: 5V / 2A
183.7 × 79.9 × 31.9mm | 360g

Product

5 10
8

13 9

11 12

6
1 Function key 2 Power key 3 Type-C 4 Indicator LED 5 NFC reader area 6 ICCR card slot 7 MSR card slot

8 Light-sensor 9 Rear Camera 10 Top Camera 11 Speaker 12 POGO Pin 13 Printer

Usage
Charge Port 2
Insert

7 1

6 5 4

Power ON/OFF
Power ON: Press and hold the power key until the LCD screen turns on. Power OFF: Press and hold the power key until the LCD screen turns off.
QR code

Charge POGO Pin

BankCard 08/16
Slide

Swipe

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: –Reorient or relocate the receiving antenna. –Increase the separation between the equipment and receiver. –Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. –Consult the dealer or an experienced radio/TV technician for help.
The device has been tested and comply with FCC SAR limits. For body mode, please keep the device minimum 10mm when normal use.

Documents / Resources

TOPWISE T6 Android Smart Mobile POS [pdf] User Manual
2BBKD-T6, 2BBKDT6, T6 Android Smart Mobile POS, T6, Android Smart Mobile POS, Smart Mobile POS, Mobile POS, POS

References

User Manual