tommee tippee goprep Portable Formula Feed Maker Instruction Manual
IMPORTANT WARNINGS!
These instructions can also be found at www.tommeetippee.com Keep this instruction sheet for future reference as it includes important information.
- Flask can contain boiling water – a potential scalding hazard. Ensure lids are securely fastened. Open with care. Always use on a flat surface
- Handle freshly boiled water carefully.
- Adult use only.
- Please keep out of reach of children.
- Inspect before use. Throw away at first signs of damage or weakness
- Do not use to store or carry carbonated drinks.
- Always check food temperature before serving and feeding.
- When making up a feed, follow the formula manufacturer’s instructions
- Do not use in a microwave oven.
- Do not use with any other liquid than water in the preparation of a formula feed.
- In order to minimise bacterial growth do not use to keep warm milk products. Use only as directed in HOW TO USE section.
- Always allow the cooling flask to reset before use and handling (3-4 hours).
- Handle the cooling flask carefully as the base will heat up when in use. Leave the cooling flask to cool after steam sterilisation.
- Use the cooling flask in a safe environment, away from baby.
WARNING: The battery is hazardous and is to be kept away from children (whether the battery is new or used). The battery can cause severe or fatal injuries in 2 hours or less if it is swallowed or placed inside any part of the body; Medical attention should be sought immediately if it is suspected the battery has been swallowed or placed inside any part of the body.If you suspect a child has swallowed a button battery, immediately call; In Australia; the Poisons Information Centre on 13 11 26 In New Zealand; Poisons Prevention on 0800 764 766 or go to a hospital emergency room. Do not let the child eat or drink and do not induce vomiting.
STORAGE
- Do not store in direct sunlight or near a source of heat.
- Do not store with or allow to come into contact with solvents or harsh chemicals.
- Keep all components not in use out of reach of children.
Shaking the cooling flask starts the cooling process.
BEFORE USE
- Clean and disinfect the surface you are going to use. It is important that you wash your hands.
- Fill the kettle with fresh tap water (do not use water that has been boiled before). Boil the water. Take care when handling fresh boiled water.
HOW TO USE
Hot flask
(If included) Fill the hot flask with boiling water to take out of home with you. Water will remain hot for up to 4 hours if filled to the max level excluding the neck. Always ensure the pouring insert is in place before you screw the lid on.
Using the cooling flask
- Press and hold the power symbol for 3 seconds to turn the lid on/off. Once the lid is switched on a blue star will appear. If inactive, the blue star will disappear after 3 seconds but the lid is still switched on. The lid will automatically turn off after 12 hours to reserve battery power.
- Add boiling water to the cooling flask, using the graduation marks on the inside of the flask as a guide.
- Measure out the formula as per manufacturer instructions and store in the milk powder dispenser until it’s ready to use.
- When you’re ready to feed, screw the digital lid and turn the cooling flask upside down for a minimum of 5 seconds. Tap the power symbol to display the star on the digital lid, it should turn red or orange.
- Dispense the correct amount of formula powder, as per manufacturer’s guidelines.
- Ensure the lid is screwed on correctly and shake well to mix the powder with the hot water, ensuring it’s fully dissolved. Shaking the cooling flask starts the cooling process.
- The time it takes for the feed to cool depends on the feed size, refer to the cooling times table. To check if a feed is ready to dispense into a baby bottle, tilt the cooling flask upside down for a minimum of 5 seconds so the milk touches the digital lid. Tap the power symbol to display the star, the lid will show a blue star when the feed is ready. Don’t dispense the feed before 2 minutes.
- Decant your feed into a clean, sterile bottle, and follow bottle feeding instructions. Always check the temperature before feeding your baby. Once a feed is made, use immediately.
DIGITAL LID
The integrated thermometer in the digital lid will activate the digital screen when it comes into contact with water or milk. The digital lid will tell you when a feed is ready for baby (blue star), but also when water is still hot enough to start making a feed (red or orange star). To help maintain battery life switch the digital lid off between feeds by pressing the power symbol for 3 seconds.
When testing the temperature of milk (on the cooling flask)
Under most circumstances the digital lid will not show a red star when attached to the cooling flask. This is because the cooling flask will start cooling the feed immediately and brings the feed temperature below the range that would show a red star. If the lid shows a flashing red star it indicates a problem with the thermometer. Please do not use the product and contact our customer services.
COOLING TIMES
Cooling times should be used as a guide only. Always check food temperatures before feeding. Always follow formula powder manufacturer’s instructions for making a feed.
COOLING FLASK RESET TIMES
The cooling flask works by absorbing heat from hot liquids. After being exposed to heat, it will require a minimum of 3 hours before being ready to use again.
CLEANING & STERILISATION
Hot flask
(If included) The hot flask base, lid and pouring insert can be cleaned in warm soapy water.
Cooling flask
The cooling flask base can be cleaned in warm soapy water or a dishwasher. The digital lid can only be washed in warm soapy water, take care to remove the silicone seal and use the small brush provided to clean behind the seal any excess of milk. Follow the instructions below to sterilise the cooling flask with the digital lid.
- Fill the flask with 240ml of boiling water.
- Secure the digital lid and shake for 10 seconds.
- Place the cooling flask on a stable surface for 2 minutes.
- Turn the cooling flask upside down for 2 minutes.
- Safely discard the water.
WARNING: Always keep out of reach of children. Take care to avoid the flask being knocked over during the sterilisation process.
Alternative sterilisation methods
Descaling (flask base only)
To avoid the build-up of limescale the container should be periodically cleaned. The best results are obtained using a mixture of water and bicarbonate of soda or washing up liquid. Rinse thoroughly afterwards.
Information on the Disposal of Waste Electrical and Electronic Equipment (WEEE)
This symbol means that your product shall be disposed of separately from household waste in accordance with local laws and regulations. When this product is ready for disposal, take it to a collection point designated by local authorities. Separating and recycling of your product at the time of disposal will help conserve natural resources and ensure that the product is recycled in a manner that protects human health and the environment. Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation.
Leaflet No: 0423774 P7
Mayborn )UK( Limited, Balliol Business Park, Newcastle upon Tyne, NE12 8EW, UK.
EU Representative. Mayborn France Sarl, 56 Rue de Paris, Boulogne Billancourt, 92100, France.
Mayborn ANZ Pty Ltd. (ABN 66 154 703 134), Unit 21, 15 Ricketts Road, Mt Waverley, Victoria 3149, Australia.
All IP rights held by Mayborn (UK) Limited and/or its affiliates.
TOMMEE TIPPEE®. GO PREP™. Copyright © 2024.
Made in China.
Any questions?
Visit our website: tommeetippee.com
Documents / Resources
 |
tommee tippee goprep Portable Formula Feed Maker [pdf] Instruction Manual goprep Portable Formula Feed Maker, goprep, Portable Formula Feed Maker, Formula Feed Maker, Feed Maker |