TOLSEN 35343 Self Leveling Cross Line Laser Level Instruction Manual

BEFORE YOU START

General laser safety warnings

IMPORTANT:

• Please read this instruction manual carefully before using the product, and familiarize yourself with the operation, adjustments, and functions of the various switches.
• Consider and follow the safety and operating instructions in order to avoid possible risks and hazards.
• Keep these instructions for future use. If the product is passed on to a third party then these instructions must be included.

WARNING! Danger of permanent eye injury!

• Laser radiation! Do not stare into beam.
• Class II laser product.

WARNING!

• DO NOT operate the tool around children or pets, this product is not a toy and is not intended for use by children.
• DO NOT remove or destroy any label appearing on this instrument.
• DO NOT stare directly at the laser beam, as this can cause blindness. Only turn the laser ON when being used.
• DO NOT place the tool in a position that may cause anyone to stare at the laser beam, whether intentionally or unintentionally, and ensure bystanders are aware of the dangers.
• DO NOT point the laser beam emitted by the instrument at people or animals.
• DO NOT point the laser onto shiny or reflective surfaces such as glass or polished metals, as this could reflect the beam back at the operator or passers by.
• DO NOT attempt to modify the performance of this laser device in any way.
  This may result in a dangerous exposure to laser radiation.

CAUTION!
35141 V20231106

• DO NOT attempt to repair Ord assemble the laser-measuring tool. If un qualified persons attempt to repair this product, serious injury may occur Andrea required on this laser product should be performed only by qualified service personnel
• DO NOT operate the tool in explosive environments, such as in the presence of flam ma bleliqu ds, gases or dusts Sparks can be created in the tool which may ignite the dust or fumes.
• ALWAYS turn of the instrument whenever it is not n use Failure to do so will in crease the possibility of someone inadvertently looking directly at the laser beam
• DO NOT use optical instruments with this product, as this will increase risk of injury to the eyes
• DO NOT use laser viewing glasses as safety goggles, as they do not protect the eye saga nstlaserr audiation.
• DO NOT use parts or accessories that have be en de signed for use with other laser tools, as these could result n serious injury or loss of performance.
• The accuracy or performance of the in strumming maybe reduced if it s used beyond it’s des geed range, or in strong lighting conditions
• DO NOT expose the product to shock, continuous vibration or extreme hot or cold temperatures, as this could damage the tool and/or cause serious jury to the user.
• ALWAYS handle the laser product with care. Treat it as you would any other opt cal device such as a camera or binoculars, and DO NOT touch the lens d erectly.

To install batteries

1. This instrument reup res 2 x 15V A batteries
2. Remove the battery compartment cover.
3. Insert the batterers paying attention to the polarity (+/-) marked on the compartment and batterie s
4. Close the battery compartment cover.

CAUTION!

• ALWAYS turn of the instrument before replacing the batteries.
• ALWAYS remove the batters if the instrument is not to be used for extended periods.
• ALWAYS use high quality batters of the same brand, type and age.
• If the instrument does not work properly, or the low battery icon is displayed, replace the batter seemed lately.
• DO NOT expose the batteries or instrument to extreme temperatures or direct heat source, as this can cause the batteries to leak.
• If the batteries should leak, remove them using a cloth and dispose of them accord ng to local regulations. Clean any leaked battery acid avoiding any cont. act with sk n, eyes & mouth
• If any contact does occur, rinse affected a reskimmed atelia with fresh water and seek medical advice.

FUNCTIONS AND SETTINGS

Operation instructions
Your self-levelling cross-line laser level has two working modes.

Self-levelling mode
In this mode, the tool will level itself if it is within ±4° of horizontal.

1. Place the self-levelling cross-line laser level on a flat, smooth surface that is within ±4° of horizontal.
2. Turn the tool on by sliding the Lock switch to the up position. The self-levelling cross line laser level will automatically level within 5 seconds.
3. Press the mode button until the desired laser-projection mode is achieved and the laser line is projected from the laser aperture.
4. If the laser level is greater than ±4°, the laser line will blink.
5. To turn off the laser lines, slide the Lock switch to down position. Press and hold the mode button until the laser shuts off.

Manual mode
This mode cannot be used to perform horizontal or vertical levelling, because the laser lines are no longer self-balancing.
In this mode, the laser line will flash every 3 seconds.

1. Keep the Lock switch off.
2. Press the mode button to turn the laser on and to change the laser-projection mode.
3. To turn the laser off, press and hold the mode button until the laser shuts off.

CLEANING

• To ensure the instrument operates at optimal performance it should be regularly cleaned.
• ALWAYS switch the instrument OFF before cleaning.
• The housing can be cleaned with a damp cloth, taking care that no water enters the product.
• DO NOT immerse the electrical/optical parts of the product in water or other liquids, and never hold it under running water.
• Any lenses can be cleaned using a cotton bud with a small amount of distilled water or alcohol.
• After cleaning, ensure that all parts dry properly before use.
• The product should be stored carefully, so that it is protected from dust and scratches.

TECHNICAL DATA

Wavelength	635nm
Beam Accuracy	H/V Line ±3mm/10 m
Expanded Angle	H&V 120°
Max. working distance	20m
Power Supply	2xAA battery
Operating time	8h
Ingression Protection Rate	IP54
Operating Temperature	-10°C – +50°C
Storage Temperature	-20°C – +70°C
Model Function	switchable manual model

SAVE THIS MANUAL!

You will need this manual for safety instructions, operating procedures and warranty.
Put it and the original sales receipt in a safe dry place for future reference.


SCAN TO VISIT PRODUCT LINK 35141

SUZHOU TOLSEN TOOLS CO.,LTD.
www.tolsentools.com
TOLSEN is a trademark or registered trademark of TOLSEN TOOLS. All rights reserved.
MADE IN CHINA

Distributor
Sunnysoft s.r.o.
Kovanecká 2390/1a
190 00 Prague 9
Czech Republic
www.sunnysoft.cz

Documents / Resources

TOLSEN 35343 Self Leveling Cross Line Laser Level [pdf] Instruction Manual 35141, 35343 Self Leveling Cross Line Laser Level, 35343, Self Leveling Cross Line Laser Level, Leveling Cross Line Laser Level, Cross Line Laser Level, Line Laser Level, Laser Level

References

• User Manual